Vector

VECTOR VISION 7 hexacopter, assembled Rigid machine

VECTOR VISION 7 hexacopter, assembled Rigid machine

Vision behind Vector multicopters, Just A Minute to retract it from the Peli case, and you ready to Flight. Lightweight, rigid, produced in Europe.

More Photos - CLICK HERE

Vector Vision body has two parts. Upper frame and lower frame. Upper frame has only four different parts excluding nuts and bolts. It is the simplest possible solution to hold motors and motor speed controllers. Lower frame is connected to upper frame with dampeners. Lower frame serves platform for retractable landing gear, flight packs, video link, data link and gimbal quick release system. Significant mass is concentrated on lower frame isolating it from potential vibrations from upper frame. Dampers can also be adjusted to softer or harder type if needed to allow fine tuning.

Autopilot is placed in exact center of the frame. It has two trays that attach to the top center plate. Vector Vision can be equipped with Zero UAV X4 or Wookong autopilot versions. Our recommendation is to use the new X4 P pilot with best IMU and 50 waypoints. This is usually enough for even demanding missions. In autopilot platform IMU is also positioned so that sensors are in same plane as the propellers. Compass and GPS have their own place on top deck, again in the center of the aircraft. All wires are carefully hidden in the autopilot deck compound.

Operator needs around one minute to open carrying case and unfold Vector Vision and connect power. After autopilot system check its ready to take off. There is no other system available in the market today that comes anywhere near this.

Gimbals or other instruments can be connected to Vector Vision platform with quick release system. The Quick release plate is designed to hold up to 2,5kg of instrument weight. It has also a special bus for connecting all gimbal electronics to flight control system. Quick release connector plate is separately available to mount your own instruments. Vector Crane gimbals have the right connection as standard.

Vector Vision has a manual retractable landing gear as standard. Landing gear is designed so that it can easily be upgraded with motor driven gear system. This can be done by replacing the centerpiece with integrated gear motor. Retracts can also be ordered as an option

VECTOR VISION 7

  • Vector multicopters have been designed to meet RPAS regulations
  • Maximum flying weight 5 kg
  • Configuration - hexacopter, Assembled, Tested
  • Diameter from motor to motor 720 mm
  • Prop size 13"
  • Max battery 2 X 3S 6600 mAh (2 x 74Wh)
  • Operating voltage 22,2V
  • Standardf Flight Controller Zero UAV X4 wifi
  • Quick release connection for instrument platform mechanical and electronics
  • Retractable landing gear is option (will use extra120 g of payload)

Included:

  • Frame: Configuration - hexacopter
  • Motors: Tiger MN3508
  • ESC: TIGER PRO 30A
  • PROPS: TIGER CARBON 13"
  • Flight controller: Wookong

Delivery time: 1-2 Weeks, Gimbal & Camera not included!

Recommended equipment to complete:(can be delivered as option)

  • Futaba 14SG radio
  • Lipo battery 3s 5000 x 2
  • Charger 500-1000w

€2599.00


€2147.93 Ex VAT
Quantity
VectorSave 10 Mavic Pro & Pro Platinum parachute rescue system

VectorSave 10 Mavic Pro & Pro Platinum parachute rescue system

VectorSave™10 Mavic parachute system is a 75g total safety solution for DJI Mavic helicopters. The system has easy back-pack clip connection top of the frame. It can be mounted or removed in seconds. It does NOT require any modification to your DJI Mavic so your warranty is not voided. VectorSave™ Mavic is by far the best insurance for your drone and any valuable property around the area you will be operating your drone.

VectorSave™ Mavic parachute system all-in-one solution. The launch tube holding the parachute has built-in sensor and power. It will detect extreme angle and free fall deploying the parachute on those conditions. Tube can be reloaded unlimited times.Parachute is packed inside the tube and parachute shock cord is connected to simple harness.

Details:

  • System weight: 75g
  • Parachute size: 0.6m2

Launch conditions:

  • Angle
  • Free fall
  • Charge and firmware update connector: micro USB
  • Shock cord strength: 420 kg

€359.00


€296.69 Ex VAT
Quantity