SpeedyBee F405 V3 BLS 50A 30x30 Flight Controller & ESC Stack

Our Price

108.00


89.26 Ex VAT

Seen it cheaper?

Availability
Low Stock
Ships same day if placed before 12H
SKU SB-F405-V3
Quantity

Purchase this product now and earn 108 Points!



Description

SpeedyBee F405 V3 BLS 50A 30x30 Stack FPV FC Flight Controller ESC

Configure your FC and ESC via Bluetooth

Turn your phone into an all-in-one FC configurator with the SpeedyBee app and tune your quad anytime, anywhere.
Experience wireless, fully configurable ESC with the SpeedyBee app.

Powerful 50A 4-in-1 ESC!
Built with the robust BB21 MCU and large motor pads for easy soldering. Built with Japanese-made TDK filter SMT capacitors and TVS protection diode on board, for a smooth flying experience. Real 50A output, ready for your 6S motors.

Forgot your LiPo checker?
Just check the FC! Equipped with a 4-stage LED battery indicator, you can now fly anywhere worry-free - even without your lipo checker!

8 Motors Output for X8/Y6/ fixed-wings
You can use this stack for your X8 drones, Y6 drones or fixed wings. Just take out your phone and configure everything in the SpeedyBee app.

Change motor directions wirelessly!
Finish your last build? Just replaced your motor after a crash?
Take out your smartphone and configure the direction of your motor wirelessly with the latest SpeedyBee app. Works for all BLHeli32 / BLHeli_S / BlueJay ESCs.

low ESR 1500uF capacitor + TVS protection diode = Additional protection
The ESC is equipped with a TVS protection diode to absorb voltage spikes. We also included a huge 1500uF low ESR capacitor. Capacitor to provide clean data from the gyro to the FC.

Specifications SpeedyBee F405 V3 30x30 Flight Controller

  • MCU: STM32F405
  • IMU(Gyro): BMI270
  • USB port: Type-C
  • Barometer: Built-in
  • OSD chip: AT7456E chip
  • BLE Bluetooth: Supported. Used for flight controller configuration
  • DJI Air Unit Connection Way: Two ways are supported: 6-pin connector or direct soldering.
  • Blackbox MicroSD Card Slot: *Betaflight firmware requires that the microSD card type be either standard (SDSC) or high capacity (SDHC), so extended capacity (SDXC) cards are not supported (many high speed U3 cards are SDXC). Also, the card MUST be formatted with the FAT16 or FAT32 (recommended) file system. So you can use any SD card less than 32GB, but Betaflight can only recognize a maximum of 4GB. We recommend you to use this third-party formatting tool and select "Overwrite format" to format your card. Also check here for the recommended SD cards or buy the tested cards from our store.
  • BetaFlight Camera Control Pad: Yes (CC Pad on the front)
  • Supported current sensor inputs: For SpeedyBee BLS 50A ESC, please set scale = 386 and offset = 0.
  • Current input: 3S - 6S Lipo (through G, BAT pins/pads from 8-pin connector or 8-pads on the bottom)
  • 5V output: 9 groups of 5V outputs, four +5V pads and 1 BZ+ pad (for buzzer) on the front and 4x LED 5V pads. The total current load is 2A.
  • 9V output: 2 groups of 9V output, one +9V pad on the front and another in a connector on the bottom. The total current load is 2A.
  • Supports 3.3V output: Designed for receivers with 3.3V input. Up to 500mA current load.
  • Supports 4.5V output: Designed for receiver and GPS module even if FC is powered by USB port. Up to 1A current load.
  • ESC signal: M1 - M4 on the bottom and M5-M8 on the front.
  • UART: 5 sets (UART1, UART2, UART3, UART4 (for ESC telemetry), UART6)
  • ESC: Telemetry UART R4(UART4)
  • I2C Supported. SDA & SCL pads on the front panel. Used for magnetometer, sonar, etc.
  • Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on the bottom of the front panel. Used for WS2812 LEDs controlled by Betaflight firmware.
  • Buzzer: BZ+ and BZ- pads are used for 5V buzzer
  • BOOT button: Supported.
  • [A]. Press and hold the BOOT button while powering on the FC to put the FC into DFU mode.
  • [B]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the bottom panel. By default, a short press of the BOOT button will toggle the LED display mode. A long press of the BOOT button toggles between SpeedyBee LED mode and BF LED mode. In BF-LED mode all LED1-LED4 strips are controlled by the Betaflight firmware.
  • RSSI input: is supported. Referred to as RS on the front panel.
  • SmartPort: use any TX pad of the UART for the SmartPort function.
  • Supported flight control firmware BetaFlight (default), EMUFlight, INAV
  • Firmware target name: SPEEDYBEEF405V3
  • Mounting: 30.5 x 30.5mm (4mm hole diameter)
  • Dimensions: 41.6(L) x 39.4(W) x 7.8(H)mm
  • Weight: 9.6g

Specifications SpeedyBee BLS 50A 30x30 4-in-1 ESC

  • Firmware: BLHeli_S JH50
  • Wireless configuration: full configuration supported in SpeedyBee app
  • Continuous current: 50A * 4
  • Burst current: 55A(5S)
  • TVS protection diode Yes
  • External capacitor 1500uF Low ESR capacitor (in the package)
  • ESC Protocol DSHOT300/600
  • Current input 3-6S LiPo
  • Current output VBAT
  • Current sensor support (scale=386 offset=0)
  • Mounting 30.5 x 30.5mm (4mm hole diameter)
  • Dimensions 45.6(L) * 44(W) * 6.1mm(H)
  • Weight 13.8g

Contents:

  • 1x SpeedyBee F405 V3 flight controller
  • 1x SpeedyBee BLS 50A 4-in-1 ESC
  • 1x 35V 1500uF low ESR capacitor
  • 5x M3 nylon nut
  • 5x M3 silicone O ring
  • 5x M3*8mm silicone grommets (for FC)
  • 5x M3*8.1mm silicone grommets (for ESC)
  • 1x SH 1.0mm 15mm long 8-pin cable (for FC-ESC connection)
  • 5x M3*30mm hexagon socket screws
  • 1x DJI 6pin cable (80mm)
  • 1x XT60 power cable (70 mm)

Need Some Advice?

Complete the form below and we'll get back to you...


We'll never share your email with anyone else.

Seen it cheaper than €108.00 ?

Complete the form below and we may be able to match, or even beat the price...


We'll never share your email with anyone else.
Must be a valid URL to the competitor's product page that displays the price
 
Terms & Conditions

Please do not send any messages trying to compare prices with unknown shops. We will only match with official shops located in Europe.

A store that has no physical shop, no showroom, no physical contact info, no return policy, including 'home garage shops' are NOT considered as an official store.

We are working hard to bring you low prices. But selling a product without warranty (after-sales service) is not our vision. Sometimes our support and advice is worth more important then the product itself.

To receive a price match, please read the conditions and make sure you qualify for a price match and then submit a request using the price match form on the product page.

Conditions:

  • Price matches are honored on identical items only. Same brand, same tech specs, same warranty conditions. *
  • The item must be brand new, make sure the company you want to match has the product IN STOCK!
  • We only price match with official stores within the EU and the products have to come from official importer/producer in Europe.
  • The competitor must be a physical and authorized dealer of the item you wish to purchase.
  • Special sales or events cant be covered with price match policy.
  • If you happen to find a lower price (please check shipping costs!) on an identical item, just show us the price (including delivery costs).
  • Sometimes due the Prices updates some companies showing old -not updated prices. be aware about this

* Some products within EU have different sockets, example UK chargers which do not fit in Europe.

How to Apply:

Simply fill a price match request online at the time of order by including the competitor's URL for the item in the comments section of your order form.

This is an individual response, We will acknowledge your request within 24-48h and provide instructions for next steps.

Please note this is a manual process and you will not be able to physically adjust the price on your on-line order.

If you need a more immediate response, please call +32 486 808080.

Remarks:

Our price match does not apply to competitor's bonus offers, free offers, auction websites, non-retail (wholesale) websites, private sales, special orders, typographical errors, clearance sales, liquidation sales, mail-in rebate offers, or where a service commitment is included in the transaction.

Internet competitor offers must include shipping and handling charges as the basis for comparison.

Certain UK products are not covered by European warranty. Check with us for compatibility issues.

Price matching is subject to providing proof of the manufacturer's part number and availability of the product. (i.e. current dated advertisement, register receipt, copy of webpage or catalog page) of a lower price.

Please consider the price matching as an action of good will, we reserve the right to refuse any request.

These terms and conditions may change at any time without notice.