Spartan RC

Bluetooth enabled PC, PDA or mobile phone supporting SPP (Serial Port Profile).

Spartan provides software for certain platforms only. Such software is available on the Spartan website and we advise that you download and try it to ensure compatibility with your PC, PDA or mobile phone before purchasing a Blue-Link. The software can be found on the page of the product you wish to interface to.

Specification
Class 1 Bluetooth radio offering a maximum range of 100m when used in conjunction with a class 1 capable device and subject to environmental conditions, obstructions and ambient noise levels.
Dimensions 46 x 20 x 11mm (1.8 x 0.8 x 0.43 inch)
Power and data leads 26cm long (10.2 inch)
Weight 12 grams including leads.
Power supply 4 - 8.4 Volts, current draw <100mA
Operating conditions: 0 to 50 deg C, 32 to 122 deg F, 20 to 85 % humidity not condensing.
Storage: -20 to 70 deg C, -68 to 158 deg F, 20 to 90 % humidity not condensing.

 

SPARTAN Gyro Metal plate
Gyros are sensitive to high frequency vibrations. The metal plate helps isolate these vibrations and not allow these vibrations to be transmitted to the Gyro. If your gyro was working fine and then suddenly started to drift try to find the source of this possible vibration.

We recommend to use the metal plate between the gyro pads.

1 metal plate in a set

SPARTAN Simplex Data Adapter (SLX Adapter)

Certain Spartan products such as the Quark gyro have the ability to be connected to a computer, but due to size or other constraints they do not offer a dedicated data port. This SLX Adapter provides the required data port via intelligent sharing of other plugs. The illustration below shows how the Quark gyro is connected to a computer through sharing of the gain plug.

This product does not provide computer connectivity on its own. It must be used in conjunction with a Flash-Link or Blue-Link.

 

 

SPARTAN Replacement gyro pads for gyros .
The pack includes (5x) "3M" 30x30x2mm, (1X) Metal plate

Spartan Vortex Nano VX1n Flybarless System

Designed for 3D Pro pilots and beginner alike the Vortex VX1 and VX1n will amaze you with their performance, features and intuitive installation.

Tail - Based on Spartan's market leading gyro technology the Vortex is capable of delivering exceptional tail hold and consistent yaw rates even at eye-blurring speeds of over three full turns per second.

Rotor - The cyclic and collective controls are smooth and precise with a very solid feel and impressive response time. Factory calibrated sensors and Spartan's proprietary piro compensation technology enable your helicopter to remain locked in through piro moves.

Governor - The built in governor provides Nitro and Electric* modes and support for both magnetic and phase sensors. Cross mixing and look-ahead algorithms ensure that power is delivered in time and not as a result of RPM decay.

Receiver - The Vortex supports SBUS & PPM single wire receiver connections, 1 or 2 Satellites and individual channel connections to traditional receivers. Additional channels provided by SBUS, PPM & Satellite receivers can be routed to the three AUX outputs.


Key features:

• Designed for all helicopters; from the smallest electric to the largest nitro
• Market leading tail hold and pirouetting consistency
• Small and lightweight
• Suitable for normal, DFC, rigid and multi-bladed rotor heads
• Compatible with all digital tail servos (760us, 960us and 1520us)
• Compatible with digital and analog swash servos
• Compatible with standard pulse, PPM, SBUS and 1 or 2 satellite receivers
• Built in governor with Nitro and Electric* modes
• Superior balanced ring MEMS sensor technology
• Easy configuration and field adjustments via the Spartan DataPod. You can deploy a new system in minutes
• Firmware upgradable
• Four configuration memories that can be selected in-flight for different flying styles. They can be mapped to Normal, Idle1, Idle2 & Hold or as the user requires
  

Key features:

• Dimensions control unit: 34 x 23.8 x 11mm (1.34 x 0.94 x 0.43 inch)
• Dimensions sensor: 20.6 x 20.6 x 9.6mm (0.81 x 0.81 x 0.36 inch)
• Weight: 14 grams (combined control unit & sensor)
• Sensor lead: 16cm long (6.3 inch)
• Sensor Type: Balanced ring MEMS with digital interface
• Governor: Selectable Nitro or Electric*
• Control system: Proprietary PID with adaptive tuning
• Supported tail servos: Digital 760us, 960us and 1520us centre pulse
• Supported swash servos: Digital or analog 1520us centre pulse
• Supported receivers: Standard pulse, PPM, SBUS, 1/2 Satellites
• Standard setup: DataPod
• Computer connectivity: DataPod Bridge Mode
• Operating voltage: 3.8V to 8.4V
• Current draw: <100mA

Box contents:

Spartan VX1 control unit
Spartan VX1 sensor
VX1 welcome card
Receiver cable set
Adhesive foam pads

SPARTAN Vortex VX1 Wire Set

This pack includes a complete set of wires for connecting the Vortex to a standard receiver.
The heavy gauge male-male wire can also be used for PPM or SBUS connections.
This is the same set of wires supplied with the Vortex VX1 flybarless system.
Servo-Servo wire length 90mm.
Servo-Sat wire length 100mm.

Suitable for: Vortex VX1, Vortex VX1n

SPARTAN Vortex VX1n Wire Set

This pack includes a complete set of wires for connecting the Vortex to a standard receiver.
The heavy gauge male-male wire can also be used for PPM or SBUS connections.
This is the same set of wires supplied with the Vortex VX1n flybarless system.
Servo-Servo wire length 145mm.
Servo-Sat wire length 210mm.

Suitable for: Vortex VX1, Vortex VX1n