SM-Modellbau

External Buzzer for LiPoWatch

External Buzzer for LiPoWatch

External Buzzer for LiPoWatch

External buzzer signal for the LiPoWatch.
Simply plugged in and gives appropriate warnings with a hight level of noise!

Specification:

  • Size: 13 x 13 x 7mm
  • Weight: 3g

€9.90


€8.18 Ex VAT
Quantity
Lipo 10s adapter board for LiPoWatch

Lipo 10s adapter board for LiPoWatch

Lipo 10s adapter board for LiPoWatch

Specification:

  • Size: 36 x 18 x 8 mm
  • Weight: 3g

€7.90


€6.53 Ex VAT
Quantity
Lipo 12s adapter board for LiPoWatch

Lipo 12s adapter board for LiPoWatch

Lipo 12s adapter board for LiPoWatch

Specification:

  • Size: 46 x 18 x 8 mm
  • Weight: 6g

€10.90


€9.01 Ex VAT
Quantity
LiPoWatch

LiPoWatch

LiPoWatch

The cell monitoring protects your impulse battery against deep unloading and stores at the same moment as a Datalogger the tension of every separate cell.

The LiPoWatch is a cell monitoring for up to 15 cells (15S) LiPo and LiFePo of battery. He supervises every cell of the battery stack and can do while remaining an adjustable threshold the impulse so that the cells are not unloaded deeply.
The externally connectable buzzer (ord. no 2610) announces remaining tension threshold and other mistakes.

In addition, the LiPoWatch records the tension all connected cells separately and serves with it as a Datenlogger for the monitoring of the battery.
The flights of a whole weekend can be recorded

A red LED by every cell connection makes possible a quick view which cell has released the undervoltage message or another warning.

About our UniDisplay all measured values of the LiPoWatch can be selected directly at the airfield and be considered.
As well the minimum values of the last measuring row can be read.
Also a live announcement is possible.
All settings as for example the memory rate can be programmed by display.

The evaluation of the data takes place uncomplicated with the known software LogView or the GNU DataExplorer.

On the basis of a low weight and the compact size the LiPoWatch can be used nearly in every area.
With only 11gs he is suitable as well for the control of a 2S, 3S or 14S Lipo

The LiPoWatch is also able to do this:

  • Monitoring and measurement from 2s to 15s of battery with Datenlogger
  • Regulation / disconnection of the impulse with adjustable parameters direct announcement of mistakes of a cell with own LED
  • Connection for a temperature sensor (ord. no 2220)
  • Connection for an external signal buzzer (ord. no 2610)
  • Recording the internal temperature
  • Recording the Servo-impulses of the receiver and the Servo-impulses to the regulator enormous internal data memory for almost 75000 readings sentences (dependent on the cell number)
  • Memory rates of 4 measurements per second to 1 measurement all 10 seconds make possible a recording duration from about 200 hours (dependent on the cell number)
  • Power supply automatically by the impulse battery
  • Start of the recording by lapse of time
  • Manual recording start and recording stop about inserted key of current status is signalled about a LED per cell and three general LEDs
  • direct(straight) considering of the measured values live or recorded with our UniDisplay (ord. no 2400)

Specification:

  • Tension range: 0 to 60 V (65 V) at every entrance
  • Power supply: directly from the impulse battery (4 V - 65 V)
  • External connections: 1 times Servoimpuls of the receiver 1 times Servoimpuls exit to the regulator 1 times temperature sensor (-40 °C to + 125 °C) of 1 times more external detector (peeps)
  • Dimensions: 37 x 42 x 12 mms
  • Weight: 11g

 

€79.90


€66.03 Ex VAT
Quantity
UniDisplay+ complete set with connecting cable

UniDisplay+ complete set with connecting cable

UniDisplay+ complete set with connecting cable

Comfortable evaluation and attitude possibility for our UniLog 1 + 2, GPS-Logger 1 + 2, LiPoWatch and InfoSwitch

With the help of the UniDisplay all measured values of our UniLog 1 + 2, UniSens-E, GPS-Logger 1 + 2, LiPoWatch, InfoSwitch and JLog2 can be indicated live and be put directly to parameter.

In addition, the complete data memory of the UniLog 1 + 2 or LiPoWatch can be quickly considered.
In this way one can find out (e.g., at the airport) also without big data evaluation quickly the maximum power consumption of an impulse.

The operation takes place completely simply and selfexplanatory more than four keys.

The firmware of the UniDisplay + can be updated at any time with our USB interface cable (ord. no 2550) from the PC.
The updates are at your disposition naturally free of charge on homepage: www.sm-modellbau.de

€37.90


€31.32 Ex VAT
UniSens-E 280 A Telemetry sensor with 2 x 4mm² Silicone cable

UniSens-E 280 A Telemetry sensor with 2 x 4mm² Silicone cable

UniSens-E 280 A Telemetry sensor with 2 x 4mm² Silicone cable

The small powerful RC telemetry sensor measures voltage, current, height, power, capacity and speed in a model and can be transferred to the transmitter via telemetry. Full support for telemetry of Jeti Duplex, Multiplex M-Link, Graupner HoTT, Futaba, JR DMSS and FrSky.

The Unisens E is a pure telemetry sensor especially for all electric models. It is so small and light but so powerful that it can be used in almost every model.
According to our philosophy to support as many systems, also speaks of Unisens E language of Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest, JR DMSS and FrSky.
Telemetry is used must be specified in Unisens E only once in the settings. This is done either through our PC program "Unisens E Tool" or the UniDisplay. On delivery HoTT GAM is selected.

To change the settings via PC or for firmware updates is a suitable USB interface as our Cat 2550 or an existing USB connection cable as of Jeti, multiplex or Graupner necessary. See also the instructions.
the Unisens E can measure the complete drive without additional sensors, ie voltage, current, capacitance and even the speed. A special attraction is in fact already a brushless speed sensor permanently installed. a small cable to connect to one of the three motor phases only has to be made using the cable to measure the speed.

Since barometric (atmospheric pressure) level sensor is integrated with high resolution, a Vario with Unisens E is realized in addition to the height measurement.
Similarly extensive alarms can be programmed to be reported via telemetry about individual stations.
The Unisens E is available with various connection systems, so that, normally, nothing needs to be soldered. The current range extends symmetrically in both directions. This makes the pin assignment, so that the battery male or female has the positive terminal, not matter. The measurement direction is as simple simply set in the setup.
About our UniDisplay all readings of Unisens E can viewed directly live and all settings and alarms can be programmed.

Whether gliders, aerobatic aircraft, helicopter, or HLG Slowflyer who Unisens E can be used due to its low weight and compact size in almost every area. Of course, the Unisens E is suitable not only for model aircraft. It can also be incorporated into RC boats, RC cars etc.
They acquire the Unisens E a powerful in all respects universal RC telemetry sensor that exploits the possibilities of modern electronics to give you a little helper to be a great help in dealing with your RC models.

Specs and Capabilities:

  • Complete measurement of electric drives with current, voltage, power, capacity, speed and altitude measurement
  • Integrated brushless speed sensor
  • Full telemetry support for Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest S.BUS2, JR DMSS and FrSky
  • Height measurement with automatic zeroing after switching
  • Barometric Vario
  • Current measurement range up to 140 A in both directions, voltage up to 60 V(The maximum current carrying capacity of the connectors used must not be exceeded!)
  • Connection for receiver signal for remote control of certain functions
  • Direct connection to the GPS logger possible to record data in a file
  • Measuring the battery voltage receiver
  • Power supply through receiver
  • Current status is indicated by LED
  • Direct viewing of readings live with our UniDisplay
  • Parameter settings via PC, UniDisplay and telemetry possible
  • PC software for settings and updates (SM Unisens E Tool) is available here
  • Free firmware updates via PC with our USB interface (SM-2550) or with existing USB connection cables as of Jeti, multiplex or Graupner possible (the firmware file can be found here)
  • Can be used almost anywhere due to its compact size and low weight

Technical details:

  • Measurement of: Voltage, Capacity, Current Power, RPM and Height
  • The height sensor will be reset if the model is powered.
  • Measurement range: 0 - 8000 meter.
  • Power measurement: Up to 140A
  • Voltage measurement: Up to 60V
  • Measurement of the receiver voltage
  • With the additional USB interface, the sensor can be configured and updated by PC.
  • Power usage: 25mA
  • Size: 26mm x 22mm x 11mm
  • Cable for receiver connection

 

€86.90


€71.82 Ex VAT
Quantity
UniSens-E Telemetry sensor 140A, 60V with 4mm² Silicone cable

UniSens-E Telemetry sensor 140A, 60V with 4mm² Silicone cable

UniSens-E Telemetry sensor 140A, 60V with 4mm² Silicone cable

The small powerful RC telemetry sensor measures voltage, current, height, power, capacity and speed in a model and can be transferred to the transmitter via telemetry. Full support for telemetry of Jeti Duplex, Multiplex M-Link, Graupner HoTT, Futaba, JR DMSS and FrSky.

The Unisens E is a pure telemetry sensor especially for all electric models. It is so small and light but so powerful that it can be used in almost every model.
According to our philosophy to support as many systems, also speaks of Unisens E language of Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest, JR DMSS and FrSky.
Telemetry is used must be specified in Unisens E only once in the settings. This is done either through our PC program "Unisens E Tool" or the UniDisplay. On delivery HoTT GAM is selected.

To change the settings via PC or for firmware updates is a suitable USB interface as our Cat 2550 or an existing USB connection cable as of Jeti, multiplex or Graupner necessary. See also the instructions.
the Unisens E can measure the complete drive without additional sensors, ie voltage, current, capacitance and even the speed. A special attraction is in fact already a brushless speed sensor permanently installed. a small cable to connect to one of the three motor phases only has to be made using the cable to measure the speed.

Since barometric (atmospheric pressure) level sensor is integrated with high resolution, a Vario with Unisens E is realized in addition to the height measurement.
Similarly extensive alarms can be programmed to be reported via telemetry about individual stations.
The Unisens E is available with various connection systems, so that, normally, nothing needs to be soldered. The current range extends symmetrically in both directions. This makes the pin assignment, so that the battery male or female has the positive terminal, not matter. The measurement direction is as simple simply set in the setup.
About our UniDisplay all readings of Unisens E can viewed directly live and all settings and alarms can be programmed.

Whether gliders, aerobatic aircraft, helicopter, or HLG Slowflyer who Unisens E can be used due to its low weight and compact size in almost every area. Of course, the Unisens E is suitable not only for model aircraft. It can also be incorporated into RC boats, RC cars etc.
They acquire the Unisens E a powerful in all respects universal RC telemetry sensor that exploits the possibilities of modern electronics to give you a little helper to be a great help in dealing with your RC models.

Specs and Capabilities:

  • Complete measurement of electric drives with current, voltage, power, capacity, speed and altitude measurement
  • Integrated brushless speed sensor
  • Full telemetry support for Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest S.BUS2, JR DMSS and FrSky
  • Height measurement with automatic zeroing after switching
  • Barometric Vario
  • Current measurement range up to 140 A in both directions, voltage up to 60 V(The maximum current carrying capacity of the connectors used must not be exceeded!)
  • Connection for receiver signal for remote control of certain functions
  • Direct connection to the GPS logger possible to record data in a file
  • Measuring the battery voltage receiver
  • Power supply through receiver
  • Current status is indicated by LED
  • Direct viewing of readings live with our UniDisplay
  • Parameter settings via PC, UniDisplay and telemetry possible
  • PC software for settings and updates (SM Unisens E Tool) is available here
  • Free firmware updates via PC with our USB interface (SM-2550) or with existing USB connection cables as of Jeti, multiplex or Graupner possible (the firmware file can be found here)
  • Can be used almost anywhere due to its compact size and low weight

Technical details:

  • Measurement of: Voltage, Capacity, Current Power, RPM and Height
  • The height sensor will be reset if the model is powered.
  • Measurement range: 0 - 8000 meter.
  • Power measurement: Up to 140A
  • Voltage measurement: Up to 60V
  • Measurement of the receiver voltage
  • With the additional USB interface, the sensor can be configured and updated by PC.
  • Power usage: 25mA
  • Size: 26mm x 22mm x 11mm
  • Cable for receiver connection
  •  

€65.90


€54.46 Ex VAT
UniSens-E Telemetry sensor 140A, 60V with XT60

UniSens-E Telemetry sensor 140A, 60V with XT60

UniSens-E Telemetry sensor 140A, 60V with XT60

The small powerful RC telemetry sensor measures voltage, current, height, power, capacity and speed in a model and can be transferred to the transmitter via telemetry. Full support for telemetry of Jeti Duplex, Multiplex M-Link, Graupner HoTT, Futaba, JR DMSS and FrSky.

The Unisens E is a pure telemetry sensor especially for all electric models. It is so small and light but so powerful that it can be used in almost every model.
According to our philosophy to support as many systems, also speaks of Unisens E language of Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest, JR DMSS and FrSky.
Telemetry is used must be specified in Unisens E only once in the settings. This is done either through our PC program "Unisens E Tool" or the UniDisplay. On delivery HoTT GAM is selected.

To change the settings via PC or for firmware updates is a suitable USB interface as our Cat 2550 or an existing USB connection cable as of Jeti, multiplex or Graupner necessary. See also the instructions.
the Unisens E can measure the complete drive without additional sensors, ie voltage, current, capacitance and even the speed. A special attraction is in fact already a brushless speed sensor permanently installed. a small cable to connect to one of the three motor phases only has to be made using the cable to measure the speed.

Since barometric (atmospheric pressure) level sensor is integrated with high resolution, a Vario with Unisens E is realized in addition to the height measurement.
Similarly extensive alarms can be programmed to be reported via telemetry about individual stations.
The Unisens E is available with various connection systems, so that, normally, nothing needs to be soldered. The current range extends symmetrically in both directions. This makes the pin assignment, so that the battery male or female has the positive terminal, not matter. The measurement direction is as simple simply set in the setup.
About our UniDisplay all readings of Unisens E can viewed directly live and all settings and alarms can be programmed.

Whether gliders, aerobatic aircraft, helicopter, or HLG Slowflyer who Unisens E can be used due to its low weight and compact size in almost every area. Of course, the Unisens E is suitable not only for model aircraft. It can also be incorporated into RC boats, RC cars etc.
They acquire the Unisens E a powerful in all respects universal RC telemetry sensor that exploits the possibilities of modern electronics to give you a little helper to be a great help in dealing with your RC models.

Specs and Capabilities:

  • Complete measurement of electric drives with current, voltage, power, capacity, speed and altitude measurement
  • Integrated brushless speed sensor
  • Full telemetry support for Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest S.BUS2, JR DMSS and FrSky
  • Height measurement with automatic zeroing after switching
  • Barometric Vario
  • Current measurement range up to 140 A in both directions, voltage up to 60 V(The maximum current carrying capacity of the connectors used must not be exceeded!)
  • Connection for receiver signal for remote control of certain functions
  • Direct connection to the GPS logger possible to record data in a file
  • Measuring the battery voltage receiver
  • Power supply through receiver
  • Current status is indicated by LED
  • Direct viewing of readings live with our UniDisplay
  • Parameter settings via PC, UniDisplay and telemetry possible
  • PC software for settings and updates (SM Unisens E Tool) is available here
  • Free firmware updates via PC with our USB interface (SM-2550) or with existing USB connection cables as of Jeti, multiplex or Graupner possible (the firmware file can be found here)
  • Can be used almost anywhere due to its compact size and low weight

Technical details:

  • Measurement of: Voltage, Capacity, Current Power, RPM and Height
  • The height sensor will be reset if the model is powered.
  • Measurement range: 0 - 8000 meter.
  • Power measurement: Up to 140A
  • Voltage measurement: Up to 60V
  • Measurement of the receiver voltage
  • With the additional USB interface, the sensor can be configured and updated by PC.
  • Power usage: 25mA
  • Size: 26mm x 22mm x 11mm
  • Cable for receiver connection

 

€65.90


€54.46 Ex VAT
USB Interface device

USB Interface device

USB Interface device

With this cable connection updates of the GPS-Logger, InfoSwitch, UniDisplay, UniLog 1, LiPoWatch and UniSens-E by PC are possible.

This connector cable is used for firmware updates for the GPS logger, InfoSwitch, UniDisplay, UniLog 1, LiPoWatch and Unisens E via PC. Corresponding updates can be downloaded for free on www.sm-modellbau.de.
In addition, the data stored in UniLog 1 or LiPoWatch readings can be transferred to the PC and then easily analyzed graphically. The measured values can also be viewed live on the PC with this cable.

Used chipset: FT232
Cable length: 1000mm

€19.90


€16.45 Ex VAT