CC3D APM Flight Controller Anti-vibration Damping Plate Shock Absorber Set

Included:

1 X Flight Controller Anti-vibration Plate
4 X Rubber Balls

Suits for different open source flight controller, like APM 2.5/2.6, KK, MWC, etc

GPS Metal Folding Antenna Mount Holder for Quadcopter Multicopter Black color

•   Collapsible design
•   Compatible with 4mm GPS antenna mount.
•   T6 aluminum

M10N GPS SE100 Module High Positional Accuracy Works with GLONASS/BeiDou for APM Pixhawk Flight Controller DIY FPV Drone, Quad and many other design. 

Features:

• Positioning Accuracy to 50 cm
• Positioning 20 Satellites at Open Ground in 6 Seconds
• Even at Valley Bottom, Super Station-keeping Capability
• Excellent Performance: 2.5dbl ceramic antenna design have enhances the ability to get extremely weak signal even though interference by ideal filter.
• Top Configuration: with u-blox UBX-M8030(M8), 72-channel, MMIC BGA715L7 from Infineon, that's better than single GNSS 7N.
• Built-in electronic compass QMC5883L (I2C port) with high precision, which same technology as Honeywell HMC5983. Support multiple positioning systems GPS, GLONASS L10F, QZSS L1 C/A, BeiDou B1, dual mode operation.

Compatible with Radiolink / Pixhawk Flight Controller, 1.89*1.6*0.59in, suitable for DIY drone, quadcopter, multi-copter, rc vehicle's, etc.

Package Include:

• M10N SE100 GPS x 1
• Metal rod bracket x 1
• Connecting cable x 1
• Metal fixing gasket x 2
• Foam fixed sticker x 1

GPS unit NEO-M8N with Compass for Pixhawk with extra connector for APM, For Auto

Description:

This is a new generation NEO-M8N High Precision GPS Module with Built-in Compass for PIXHAWK and APM FC (Ready to connect to PIXHAWK FC) with onboard Compass, low power consumption, and high precision, the ultimate accuracy is 0.6 meters, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy, support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and mode or more.

Additionally, you can connect the same module to APM Flight Controller just after swapping the extra 5-pin connector provided in Package.

1. Ready to Connect to PIXHAWK FC with 6-pin connector Attached
2. Receiver type 72-channel M8 engine
3. Galileo-ready E1B/C (NEO-M8N)
4. Nav. update rate1 Single GNSS: up to 18 HZ
5. Acquisition Cold starts: 26 s
6. Onboard Compass

Package included:

1 x Ublox NEO-M8NGPS for CC3DRevolution Controller

The Pixhawk I2C port Expand Board with cable I2C splitter expands the I2C port to allow up to four additional peripheral connections for Pixhawk flight controller. Use the 4-wire cable to connect the I2C splitter and add a compass module, external LED, digital airspeed sensor, or other peripherals to your vehicle. It is a useful tool and very convenient to connect. Pixhawk/APM flight control only one I2C interface, such as the need to connect more than one I2C peripheral, you can use the line board; Pixhawk – I2C points line board with five completely parallel vertical 1.25 4 a socket, convenient connection in the form of 1 drag 4 four I2C peripherals, for example, at the same time use the external compass and RGB modules. I2C line board and Pixhawk flight control the appearance of the connection

Included:

1 x I2C Splitter

1 x Wire Connector

A mini display for the Pixhawk FC – it can be used to show status info – flight mode, battery voltage, GPS lock & error codes.

Forget needing to memorise LED status sequences and buzzer tones with this handy OLED display for the Pixhawk FC. It’s a small OLED display that can be used to display key information such as the selected flight mode, battery voltage, GPS info and error codes. It will make any setup immediately more user friendly.

How to install:

Support for the onboard display is included in Copter-3.5 (and higher).

Connect the display to the autopilot’s I2C port as shown in the image above. If the I2C port is full, you can use an I2C Splitter here.

Using Mission Planner or equivalent ground station go to the parameter list and set NTF_DISPLAY_TYPE to 1

The following information will be displayed on the screen:

Arming failure messages
Flight mode
Battery voltage
GPS Lock and satellite count
Pre-arm passed/failed
EKF status

The LED Controller includes a controller board, 6 sets highlight LED strips and one USB to UART module. It is compatible with any flight controller with ardupilot or PX4 firmware like Pixhawk serial, APM serial, Pixracer, NAVIO2, PXFmini etc. It is compatible with Mavlink 1 and Mavlink 2

The front 2 LEDs (F1 and F2) show the orientation of the aircraft and get solid when the aircraft arm, breathe when disarm. The color is changeable via the configurator
The rear 2 LEDs (R1 and R2) show the status of the aircraft(GPS, RC failsafe, low battery, critical low battery, flight mode changing). Refer to the table below for more information about the aircraft status
Other 2 LEDs (F3 and F4) show solid color. The color is changeable via the configurator
All LEDs can Turn on/off via one of the Ch6 to Ch16
Aircraft status LED (R1 and R2)states

Package included:

• 1 x LED controller
• 6 x RGB LED strip
• 1 x USB to UART module
• Stickers
• Interconnecting Cables
• User manual

Based on the 3DR PixHawk, the Radiolink PixHawk PX4 Advanced Autopilot was developed with an optimized circuit design and a creative automated software QA system used during manufacturing to increase quality. The Radiolink PixHawk PX4 Advanced Autopilot has less interference of the inner components, less noise, a more accurate compass which increases safety while flying.

Radiolink PixHawk PX4 Advanced Autopilot Set Includes

• 1x PIXHAWK flight Controller
• 1x Safety Switch & Cable
• 1x Power Module (XT60 Connectors) & Cable
• 1x 3-wire Servo Cable
• 1x Buzzer
• 1x 4G Card
• 1x Mounting Foam|
  
  Specifications
• Processor
  
  • 32bit STM32F427 Cortex M4 core with FPU
  • 168 MHz
  • 256 KB RAM
  • 2 MB Flash
  • 32 bit STM32STMF100 failsafe co-processor
    
  Sensors
  
  • ST Micro IST8310 gyroscope (NEW)
  • ST Micro IST8310 accelerometer / magnetometer (NEW)
  • Invensense MPU 6000 3-axis accelerometer/gyroscope
  • MEAS MS5611 barometer
    

Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM M8N GPS Combo for Multicopters

The board integrates with PX4FMU+PX4IO .Pixhawk is with new 32 bit chip and sensor technology

Processor:
32 bit 2M flash memory STM32F427  Cortex M4, with hardware floating point processing unit
Main frequency: 256K, 168MHZ RAM
32 bit STM32F103 backup co processor

Sensor:
L3GD20 3 axis digital 16 bit gyroscope
LSM303D 3 axis  14 bit accelerometer /magnetometer
MPU6000 6 axis accelerometer / magnetometer
MS5611 high precision barometer

Interface:
5* UART, 1*compatible high voltage, 2*hardware flow control
2*CAN
Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
Futaba SBUS compatible input and output
PPM signal input
RSSI (PWM or voltage) input
I2C
SPI
3.3 and 6.6VADC input
External USB MICRO interface

Features:
Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control;
Provide redundant power input and fault transfer function;
14* PWM/ actuator output;
Bus interface (UART, I2C, SPI, CAN);
Provide automatic and manual mode;
Color LED lamp;
Multi tone buzzer interface;
Micro SD to record flight data;

Included in the package:

Pixhawk 2.4.8 FC
Buzzer+ Safety Switch
Power Module
PPM+I2C
Shock Absorber Board+SD Card
Neo-M8N GPS+GPS Holder+ OSD OLED display
DF13 4/5/6 Pin Cable

Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM PX4FMU PX4IO Combo for Multicopters

Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
Integrated backup power supply and backup controller failure, the main controller can be safely switched to backup control;
Provide redundant power and error transfer function;
14 * PWM / actuator output;
Bus interface (UART, I2C, SPI, CAN);
Offer automatic and manual mode;
Color LED lamp;
Multi tone buzzer interface;
Micro SD record flight data;

Package includes

• Pixhawk 2.4.8
  
• NEO M8N GPS ( with compass)
• Buzzer
• Safety Switch
• SD Card
• Power Module- XT60 or Deans

The safety switch (safety button) is a mandatory component of the Pixhawk autopilot system, so you can handle your vehicle's safety by turning off the engines until you activate the switch. The safety switch includes a three-position connector to connect directly to the autopilot.

Specification:

Adopts E-Switch red light switch

Length: 172mm

Package includes:

1 x Safety Switch

The modified version of airspeed head adopts digital differential pressure sensor, I2C communication, suitable for PIXHAWK, adoting PX4 original firmware
(Different from analog differential voltage sensor APM adopts, APM is not universal)
 
Package included:
1 x Airspeed module w/ 4 pin cable
1 x Pitot tube

This buzzer is used with Pixhawk and PX4 autopilot to annunciate status tones. The buzzer includes a two-position DF14 connector on one side that plugs directly into the Pixhawk or PX4 FMU board.

• Connector: DF13 Plug
• Wire length: 190mm
• Size: Dia 30mm

I2C LED Module for Pixhawk PX4 with USB Extension Function External Indicators Full Color LED- using USB-C interface (older is MicroUSB)

Pixhawk-RGB module has the following characteristics:

To extend to the exterior RGB LEDs to display, when connected to the module, built-in RGB flight control automatically turns off;

Increase the USB port for easy links from external USB cable, without limitation flight control installation location;

Pixhawk onboard identical Toshiba LED controller and Osram's high-brightness RGB LED

I2C LED Module for Pixhawk PX4 with USB Extension Function External Indicators Full Color LED, with protective cover

Pixhawk-RGB module has the following characteristics:

To extend to the exterior RGB LEDs to display, when connected to the module, built-in RGB flight control automatically turns off;

Increase the USB port for easy links from external USB cable, without limitation flight control installation location;

Pixhawk onboard identical Toshiba LED controller and Osram's high-brightness RGB LED

Pixhawk- APM Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable. The on-board switching regulator outputs 5.3V and a maximum of 3A from up to a 6S LiPo battery.

Features:

PCB Cont. Current Rating: 60A
PCB Burst Current Rating: 100A (<60 Sec)
Max current sensing: 164A
Voltage and current monitor with I2C compatible interface
Outputs 5.2V and 3A max
Weight: 20g
Current Rating: T

The Power module comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute).

This PPM encoder can encode the PWM signals from multiple channels emitted by the receiver into a PPM composite signal output.

The PPM Encoder plugs into the PWM servo output ports of any R/C receiver and encodes them into a PPM pulse suitable for many autopilots (e.g. Pixhawk). Modifications to the R/C receiver are not necessary.The whole project is based around the ATMEL ATMEGA328p AVR processor and all timing is done within interrupts so accuracy and stability is optimized .
The firmware comes pre-configured to read 8 Channels.

Product features:

Product name: PPM encoder

Color: Black

Material: plastic and metal.

Supported input channels: 8.

Output: PPM SUM x 1/MUX x 1

Size: approx. 28 x 19 x 5mm

Package weight: 10.8g

Vibration Damping by Software and Mechanical-  Achieve Higher Positioning Accurate At High-Speed

Based on the unique software vibration damping algorithm of Radiolink’s PIXHAWK and Mini Pix, mechanical vibration damping technology is added to effectively filter out high-frequency vibrations, always guarantee the accuracy of sensor data, and ensure that PIX6 achieves more accurate positioning even in high-speed mode. The helicopter can accurately lock the tail and fly stably even without installing the vibration reduction bracket.

Dual-gyro Built-in

Built-in BMI088 and ICM42688-P dual gyroscopes.

When the main gyroscope is abnormal, it will switch automatically to the secondary gyroscope, providing stronger safety protection for UAVs.

16 Channels Output

Adaptable to the dual-copter, tri-copter, quadcopter, hexacopter, octocopter, Y6 copter, X8 copter, helicopters, airplanes, VTOL fixed-wing, cars, boats, submarines, radar trackers, mowers, agricultural vehicles, etc.

OSD Module Integrated, Real-time Gesture Visualization Display

PIX6 can graphically display OSD information such as the flight direction and position of the aircraft in real-time without the need for an external OSD module. The pilot can intuitively grasp the status and coordinates* of the aircraft at any time during the first-view (FPV) flight of aircraft such as racing drones and long-distance fixed-wing aircraft. Achieve a more comfortable flying experience.

*Real-time display of flight information such as flight mode, distance, GPS stars, longitude and latitude, vertical speed, magnetic deviation, current time, battery voltage, current, wind speed, return route, exact route, vibration status, direction, etc.

Rich parameters display and thoughtful setup make the safer flight.

Unique Automation Software Testing System= Quality Assurance

The same Automation Software Testing System as PIXHAWK and Mini Pix helps realize test automation from the sensor to connection ports and interface. The test efficiency and quality assurance are far superior to traditional manual tests, ensuring the quality of every function of every PIX6

Cost-effective Solution  / Unlimited Application Potential

PIX6 works with Radiolink's latest multi-star multi-frequency centimeter-level accuracy RTK positioning system (including RTK GPS, base station, air system ground system, etc.), and is equipped with Radiolink's automatic driving control system that can realize the automatic driving of agricultural plant protection vehicles with four wheels turning 90 degrees on the spot and moving sideways, execute missions programmed automatically, designed for the agricultural vehicles has achieved the ideal operation effect and solve the industry problem of agricultural vehicles will pressing seedlings when changing lines. Help build a new form of smart agriculture.

Dual GPS Support

PIX6 supports an external dual GPS connection, ensuring stronger anti-interference capabilities, higher accuracy, and greater security.

Auto Flight by Following the Waypoints

216MHz basic frequency memory, 2MB flash memory, 512K RAM, and 32KB FRAM.

Dataflash Log can be checked makes all operations can be traced.

718 waypoints can be stored up if used for the multi-copters, and 724 waypoints can be stored up if used for airplanes, cars,

and boats which means it can be used in multiple industries such as aerial land surveying, hydrographic surveying,

autonomous search, rescue, material delivery, agricultural vehicle, and in unmanned aerial vehicle navigation.

Automatic Return, GeoFence/ Worry-free from Long-range Voyage

Support automatic return by switching, automatic return when the signal is lost or voltage is lower than settings.

Geofence settings according to the drone management regulations promulgated by the country.

It can fly within the prescribed flight airspace and fly law-abidingly.

HD Digital and Analog Video Transmission Support

It supports analog image transmission plug-and-play.

the high-definition digital image transmission DJI DIGITAL FPV SYSTEM, DJI O3 Air Unit,

or Caddx Walksnail Avatar HD System can be connected through the adapter board DiViT

to easily obtain 720p/120fps high-definition and smooth video experience.

Package includes:

1 x Radiolink PIX6 Flight controller