Other Motors

 800MX features high efficiency, superior power, excellent torque, low current draw and low temperature; it’s capable of maintaining consistent torque and head speed through continuous 3D maneuvers.
Due to the 800MX’s high efficiency and low current draw, the standard equipment 120A electronic speed controller are sufficient to experience the power of this motor, and extend battery longevity.
800MX motor incorporates radial fan in its end bell, creating powerful airflow to dissipate heat. Tweaks to motor design and reduction in weight not only contributes to dramatic power increase, the high efficiency cooling system enables cooler operating temperature during and after flights when compared to motor of previous generation.
The 800MX motor armature are dynamically balanced to eliminate typical imbalance found in other outrunner motors.
Maintenance free、high torque、high efficiency、stable, and low noise.
High-speed ball bearings, powerful magnetic outrunner rotor.
Suitable for T-REX 700E 、T-REX800E helicopters.

SPECIFICATIONS

• Input Voltage: DC11.1V-50.4V
• Max Continuous Current: 115A/250A(2sec)
• Max Output Power: 5100W/11000W(2sec)
• KV Value: 520KV
• Stator Arms: 12
• Magnet Poles: 10
• Shaft: 6x56.7x93.5mm
• Weight: 508g

Align 470MX Brushless Motor (1800KV/2818)

Based on 6s voltage, the 470MX (1800KV) motor is tailor made for the T-Rex 470L DOMINATOR, featuring superior efficiency, high power output, extreme torque, and low current, low temperature.
As a totem to the 850MX Dominator motor, The 470MX shares the same extraordinary pedigree.
Even for the none 3D pilots, 470MX 6S motor utilizes less than 5 amps at hover. Not only does this require smaller C-rating packs, the lower temperature extends the battery life at the same time. Charging time basically is cut in half. These advantages makes this an ideal motor for just about everyone.
The 470MX motor incorporates radial fan in its end bell, creating powerful airflow to dissipate heat. Tweaks to motor design and reduction in weight not only contributes to dramatic power increase, the high efficiency cooling system enables cooler operating temperature during and after flights when compared to motor of previous generation.
The 470MX motor armature had a special balance adjust to improve the serious shaking problem that other tiny motors have.
Maintenance free, high torque, high efficiency, low temperature variant, stable and quiet.
Japanese made high-speed ball bearings, powerful magnetic outrunner rotor.
Suitable for T-REX 470L series,Must with 50A Brushless ESC(Governer Mode)(HES50X01).

Specification:

• Input voltage:6S
• Max continuous current:40A/60A(2sec)
• Max output power:Approx. 890w/1300W(2sec)
• KV value:1800KV
• Stator Dimension:2818
• Stator Arms:12
• Magnet Poles:8
• Dimension:spindle 3.5x36.4x51.7mm
• Weight:Approx. 120g

Accessories:

• Socket button head screw(M2.5X6mm) x 2
• Washer(F2.6XF5.8X0.6mm) x 2
• ALIGN standard 3mm gilt terminal x 3set

 

•  To meet the power and torque requirements of enthusiasts, the high output 800MX motor was born in Alignfs R&D lab. With dramatic increase in torque and power output, capable of 4440 watts continuous power output and 8800 watts of burst power!
•  800MX features high efficiency, superior power, excellent torque, low current draw and low temperature; it's capable of maintaining consistent torque and head speed through continuous F3C maneuvers..
•  Due to the 800MXfs high efficiency and low current draw, the standard equipment 120A electronic speed controller are sufficient to experience the power of this motor, and extend battery longevity.
•  800MX motor incorporates radial fan in its end bell, creating powerful airflow to dissipate heat. Tweaks to motor design and reduction in weight not only contributes to dramatic power increase, the high efficiency cooling system enables cooler operating temperature during and after flights when compared to motor of previous generation.
•  The 800MX motor armature are dynamically balanced to eliminate typical imbalance found in other outrunner motors. 
• Suitable For TREX 700E/800E F3C.

Specification:

• Input Voltage: 22.2V - 44.4V (6-12S)
  Current (Continuous): 100A
  Current (Peak): 200A (2sec)
  Power (Continuous): 4440W
  Power (Peak): 8880W (2sec)
  KV: 440
  Stator Arms: 12
  Stator Size: 4530
  Poles: 10
  Free Shaft: 6x37mm
  Dimensions: 56.7x94.5mm
  Weight: 508g

Accessories:

•  Socket screw(M4X10)X4
•  Washer(4X10X1)X4
•  4mm gilt terminal x 3

Apply for RCM-BL500MX Motor

Specification:

500MX Motor Shaft x 1(4.8x5x67mm)
Bearings 695ZZ x 1
Bearings MR95ZZ x 1

MC3525-950KV is a high torque motor especially developed for the 450-500 CLASS  Multi-rotors platforms THIS Motor is a tuning V2 version for the older motor 3525-930kv

Fits Spyder Little, F550, and many others.

As advantage that it can be used with 9-11" props and with 4-6 S lipo, allowing you best flexible fit to multiple power combinations.

So what is so special in this motor:

- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

- Heat, 25% lower heat generation thanks to Japanese NMB bearings, resistant to vibrations.

Specifications:

•   No-load speed: 950 KV
•   Load current: 22 Amps
•   Max Watts : 325
•   No load current: 0.8 Amps
•   Japan NMB bearings
•   Weight: 60gr
•   Motor Diameter :35 mm
•   Recommended Battery: 4-6 S
•   Propellers to use: from 9-11"

Included:

•   MC3525 motor
•   Propeller mount with screws, Nut and Cup.

Sample testing data is below.

Volts-14.8  4S	Amps	Watts	Torque-gr
Prop- 10x5.5	1	13	120 gr
	4	57	395 gr
	10	143	850 gr
	16	230	1200 gr

Volts-14.8 4S	Amps	Watts	Torque
Prop-11x5	1	13	143 gr
	4	57	410 gr
	10	143	930 gr
	16	230	1350 gr

High quality brushless motor BLDC (external rotor) for model aircraft. The BOOST motor series is the result of our over 15 years of experience in the field of modern electric drives.

Product features:
- Highest manufacturing quality
- Perfect ventilation due to open housing design
- Use of the best materials
- High temperature resistant neodymium magnets
- Extra large quality ball bearings
- Long shaft 180mm available as special accessory

Range of use - model/take-off weight:
- 3D aerobatic models up to approx. 3000g
- Aerobatic models up to approx. 3500g
- Trainer up to approx. 4000g
- Gliders up to approx. 4500g

Special accessories:
Motor shaft long boost 60 / Ø=6mm / L=180mm, # 4954

Technical data:
- Dimensions: Diameter = 50mm / L = 51mm
- Weight: 345g
- Shaft diameter: 6.0mm / internal thread M3
- LiPo battery / cell count: 3 - 6 cells
- Idle speed per volt: 490 rpm-1 (KV)
- Max. Load 60Sec: 55A
- Brushless speed controller (recommended): 70Amps

Propeller (recommended):
- PI-CON 16x8 @ 3S LiPo (11,1V)
- PI-CON 15x8 @ 4S LiPo (14,8V)
- PI-CON 14x7 @ 5S LiPo (18,5V)
- APC 13x10  @ 6S LiPo (22.2V)

Scope of delivery:
- BOOST 60 brushless motor
- Aluminum mounting cross
- Propeller adapter for leading/trailing edge mounting
- Mounting screws
- Manual German/English

DUALSKY XM5010TE-4 870KV Outrunner Brushless Disk Type Motor for Multi-rotor and Airplane

Specification：

• KV: 870RPM/V
• Weight: 126g
• Diameter: 50mm
• Length: 32mm
• Diameter of Shaft: 6.0mm
• Mounting holes pitch: 19/25mm
• Slots,Poles: 24,28
• Idle Current(Io) @10V: 2.4A
• Resistance(Ri): 22mOhm
• Cruising power[8 mins]: 330W
• Bursts current[15s]: 54A
• Peak power[15s]: 600W
• Recommended ESC: XC6018BA
• Setup 1 (No. of Cell, Prop.): 3S, 14x6
• Setup 2 (No. of Cell, Prop.): 4S, 12x6
• Max. weight of 4-rotor copter: 3.3kg
• Max. weight of 3D models: 1.1kg
• Memo: 3KG 4-rotor copters, 15-25E airplanes

Brushless neodym motors MEGA are designed for direct drive (propellers, ducted fans) and for drive with gearbox. Motors MEGA AC are six-pole 3 phase AC motors, hardened steel shaft is supported in two ball bearings with permanent grease filling. Neodym magnets of dynamically balanced rotor are kevlar bandaged. Efficiency reaches up to 88%. Motor has good efficiency even at high currents thanks to vent holes. Hand made stator, lightweight rotor and design of MEGA AC motors allows permanent high rpm operation.

Motors are made in 4 lengths and are designed mostly for direct propeller drive (without gearbox). However, gearbox can be used and motor ase suitable also for ducted fan drives. Motor can be used for models from 0,8 to 5kg. Output shaft diameter of this product line is 5mm.

Technical data :

No.cells: 6 - 30 NiCd (NiMh), 2 - 10 LiPo
Dimensions: ø 36 mm, length 53,5 mm, ø shaft 5 mm
Weight: 220 g
RPM/1V: 935
Max. current:  70 A
Slope resistance: 16 mΩ
No. winds: 3

Motor Shaft for Avizar motors

MC3536-380kv , made for 6S setups, and is a high torque motor especially developed for the Multi-rotors platforms .

This motor has been custom designed and tested during 2 years, and found to be the most efficient for most multi-copters from 500cm and up, due its features.

So what is so special in this motor:

1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

2- Heat, 25% lower heat generation thanks to ceramic bearings.

3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.

4- 60cm cables, will allow direct connection to most size frames, up to 1.2 meters.

5- Special size of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.

Specifications:

•     No-load speed: 380kv
•     Load current: 19Amp
•     Burst Amps : 30 Amps
•     Power: 430 W
•     Short shaft
•     Propeller mount diameter: 6mm
•     Long cables (60cm)
•     3 x Ceramic Hybrid bearings
•     Weight: 104gr
•     Size : 35 x 36 mm
•     Poles: 14
•     Recommended Battery: 6S, 22.2V
•     Resistance 44 mOhm
•     Idle current @ 10v :0.7 Amps
•     Propellers to use: from 12" to 14"

    Included:

    MC3536-380KV motor
    Propeller mount with screws, Nut and Cup provided for choice.

See the movie showing Sky hero setting a speed record using the MC3536 motor

MC3536 is a high torque motor especially developed for the Multi-rotors platforms . made for 4-6S setups.

This motor has been custom designed and tested during 2 years, and found to be the most efficient for most multi-copters from 500cm and up, due its features.

So what is so special in this motor:

1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

2- Heat, 25% lower heat generation thanks to ceramic bearings.

3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.

4- 60cm cables, will allow direct connection to most size frames, up to 1.2 meters.

5- Special size of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.

Specifications:
 

•   No-load speed: 710kv
•   Load current: 23Amp
•   Burst Amps : 32 Amps
•   Power: 340 W
•   Short shaft
•   Propeller mount diameter: 6mm
•   Long cables (60cm)
•   3 x Ceramic Hybrid bearings
•   Weight: 104gr
•   Size : 35 x 36 mm
•   Poles: 14
•   Recommended Battery: 4S, 6S for Speedy machines!
•   Resistance 44 mOhm
•   Idle current @ 10v :1.7 Amps
•   Propellers to use: from 11" to 13"

  Included:

  MC3536-710KV motor
  Propeller mount with screws, Nut and Cup provided for choice.

 

 

 

 

Movie shows the Sky hero setting a record using this motor

Multicopter Quadrotor 5010-14 360KV Brushless Motor

1.Machined aluminum front housing with four fan-style cooling holes that pump air through the motor while it runs.

2.Rear threaded mounting holes with both 16 mm and 19mm hole spacing fit a variety of applications.

3.Specially designed NdFeB magnets with high temperature rating for trouble-free operation.

4.High Temperature 140 C (356 F) rated wire is used for winding the motors to minimize the risk of burning up the motor.

5.High quality stator plates are epoxy coated on the inner surface to prevent winding shorts. 0.20mm stator plate id used .

6.High quality shielded and permanently lubricated ball bearings are used to support the motor shaft in all our motors.

7.High temperature adhesives are used to secure the stator windings and prevent them from shifting and getting pinched or shorting out .

• Model: D5010-14
• Motor size: 50*10mm
• Shaft size: 3.17mm
• Weight: 80g
• KV(rpm/v): 360
• Battery: 2-6Li-Po
• ESC: 10A
• Cable 40cm
• Best working with props of 14-16"

Radial Mount for motors with 3mm shaft

The electric motors from the SPITZ brand are 14-pole brushless outrunners. A tempered aluminum alloy with magnesium and silicon (6061-T6) is used for a long service life. A particularly high copper filling level of the coils results in high efficiency. At the same time, very strong sintered neodymium magnets ensure high torque. The high-quality brushless motors only use precision ball bearings designed for high rotation speeds and extremely robust drive shafts. Appropriate mounting material including rear wall mounting is included in the scope of delivery.

Motor model : C3542-06

RPM : 1000kv
Power max : 750W
Input Voltage : 7-15V
Current MAX : 55A
Poles : 14
Resistance : 0.039Ω
Dimensions : ø35 x 42mm
Weight : ~132gr
Shaft Diameter: 5mm
Recommended Prop : 10x6/12x6.5/13x8

Delivered with set of accessories, Propeller adaptor, Mount, hardware

T-Motor U5 KV400 Motor U-Power Series: Stable, Durable, Powerful.

U-Power Technologies for AUW 8-12KG Multi-copter. Industrial grade, dust proof, water proof.

Unique Side Hole Design ensures swift airflow. Motor cools 2.5 times faster than others. Six holes beveling upward sparkles motor with waterproof and sand-resistant features.

Abnormal Shaft – a special screw is used for stator and rotor installation, avoiding loosiness of circlip.

High-Quality Varnished Wired – imported, oxygen-free copper coil which can tolerate temperature of 180C is employed to enhance short circuit resistance.

High-Standard Silicon Steel Sheet Precision Winding – the precision winding ensures the tightness of coil and slot. It helps reduce the copper lose while improving the utilization. Advanced 0.2mm silicon steel sheet reduces heat and eddy, thus improving efficiency.

Larger Bearing – Lower Noise: Adoption of imported German bearing prolongs the service life to over 1600 hours under trouble-free operation. German bearing enables motor run more smoothly and longer with lower noise.

Propeller Installation (Two Options, Patent Design) – Prop Installation and Traditional Installation.

Recommendation:

Voltage: 6S
Recommended prop: T-Motor CF15*5 / CF16*5.4 prop
AUW: Hexacopter, 9KG; Octocopter, 12KG.