Matek Systems

HUBOSD Eco X Type, w/STOSD8, Current Module, Dual BEC & XT60

HUBOSD Eco X Type, w/STOSD8, Current Module, Dual BEC & XT60

Matek HUBOSD Eco X Type with STOSD8 Current Module 5/12V Dual BEC and XT60 Plug

The HUBOSD8 has been designed to provide the highest possible performance and reliability in a 46*36mm & 4 layers PCB. It is a multifunctional HUB with PDB, BEC 5V/2A &12V/500mA, Current sensor 140A, STOSD8. Especially made for the mini FPV Quad. The BEC 12V is linear regulator, no LC Filter needed. Built-in STOSD8 can support Plug & Play, no complicated settings needed.

Specifications:

  • Input: 8~ 21V (3-5S LiPo)
  • PDB: 4x30A (Max.4x35A)
  • Regulated 5V and 12V outputs
  • Current Sensor 140A
  • Built-in STOSD8

€19.90


€16.45 Ex VAT
Quantity
Matek 3 In 1 Battery Monitor-Discovery Buzzer-Signal Loss Alarm

Matek 3 In 1 Battery Monitor-Discovery Buzzer-Signal Loss Alarm

Matek  3in1 device with LiPo Battery monitor, Discovery buzzer & Signal loss alarm functions. Build in ultra-high brightness LED & twin loud buzzers

Specifications:

  1. Working voltage: 5.2~26V DC, 2~6Cells LiPo
  2. Standby current less than 10mA
  3. Working current, Max 120mA (blinking & beeping)
  4. Voltage threshold setting: 3.4~3.7V/cell (Red LED)
  5. Twin loud buzzers, 85db each
  6. Ultrahigh Brightness LED, 20lm, 0.2w, Blue
  7. Size: 20x30x6mm,
  8. Weight: 7g

How to use

1. Battery monitor function (F1)

It can monitor 2~6S LiPo voltage status & notify you once the cells reach the defined voltage.
The voltage threshold of alarm & flash can be customized between 3.4V~3.7V/Cell.
1.1 If the LiPo voltage is in the range of following, The BM3in1 will detect the cell numbers automatically when the LiPo is connected.

  • 7.4~8.6V: 2cells LiPo
  • 11.1~12.9V: 3cells LiPo
  • 14.8~17.2V: 4cells LiPo
  • 18.5~21.5V: 5cells LiPo
  • 22.2~25.8V: 6cells LiPo

The BM3in1 will alarm “Be” & the voltage threshold red LED will be shown.

Hold the button 3 seconds to enter the setting of the voltage threshold.
Press button to set the alarm threshold between 3.4~3.7V/Cell(red LED) .
The value will be saved & exit if no action within 10 seconds.
During the using of LiPo, BM3in1 will detect the voltage always.
If the total voltage is below “threshold * cells”, the alarm & blink will be triggered with “Be..Be..Be……”
If the total voltage rise again, the alarm & blink will be suspended.

 If the LiPo voltage is out of the aforesaid range. The BM3in1 will alarm “Be..Be..Be” & 4 red LEDs light. Pls check if the battery total voltage is below 3.7V*cells

2. Discovery buzzer function (F2)

It is easy to use the function, Just plug it in one Aux channel(e.g. Gear).
Move the toggle switch to one side or another side, the BM3in1 will alarm “BeBeBeBeBe” & blue LED blink.

3. Signal loss alarm function (F3)

It can warn you if you turn off the transmitter first by mistake, if you have trouble finding a model in the long grass…

Turn on the transmitter first. Hook BM3in1 to the receiver THRO channel, then plug battery into model. It will detect the loss of TX signal, and emit a loud alarm “BeBe…BeBe…BeBe…” & the blue LED blink.

RX power on, the alarm & blink will be triggered as following

Turn off the transmitter first. and keep one minute.
The radio power on, but no action of stick or no signal change within one minute.

€9.90


€8.18 Ex VAT
Quantity
MATEK AP_PERIPH CAN NODE CAN Node L431

MATEK AP_PERIPH CAN NODE CAN Node L431

The AP_Periph CAN Node L431 allows you to easily connect multiple ardupilot peripherals via this node to act as a hub between your sensors and the flight controller. This is ideal for some smaller flight controllers that do not have as much I/O.

Features

CAN-L431 is an Adapter Node based on ArudPilot AP_Periph firmware.

With this board, you can easily utilize the ArduPilot driver library to convert ArduPilot supported GNSS, Compass, Barometer,Airspeed sensor, and GPIO based (PWM, Buzzer/LED notify) peripherals to DroneCAN bus peripherals.

Specifications

  • MCU: STM32L431xC, 256KB Flash
  • CAN transceiver data rates up to 5 Mbit/s in the CAN FD fast phase
  • 1x CAN, DroneCAN Protocol (2x GH-4P connectors in parallel)
  • 3x UARTs
    • UART1, spare
    • UART2, MSP default, DFU
    • UART3, GPS default
  • 1x I2C
    • for peripheral Airspeed sensor
    • for peripheral Barometer
  • 1x SPI
    • for peripheral RM3100
  • 4x ADC
    • BATT_VOLT, PIN 5
    • BATT_CURR, PIN 6
    • BATT2_VOLT, PIN 15
    • BATT2_CURR, PIN 16
  • 5x PWM outputs
  • 1x GPIO with TIM16 for buzzer
  • ST debug, SWCLK & SWDIO
  • LED
    • Blue, Fast blinking, Booting
    • Blue, Slow blinking, working
    • Red, 3.3V indicator
  • Input voltage range: 4.5~5.5V @5V pad/pin
  • Power consumption: 40mA
  • Operating Temperatures: -20~80 °C
  • Physical
    • 2x JST-GH-4P(SM04B-GHS-TB) for CAN
    • 1x JST-GH-4P(SM04B-GHS-TB) for I2C
    • 1x JST-GH-6P(SM06B-GHS-TB) for UART3+I2C
    • Board Size: 26mm*26mm*6mm. 3.7g
  • Firmware
    • ArduPilot AP_Periph MatekL431-Periph, or MatekL431-Airspeed
    • Update via DroneCAN GUI Tool

Included:

  • 1x CAN-L431 board
  • 1x JST-GH-4P to JST-GH-4P 20cm silicon wire
  • 1x JST-GH-6P to JST-GH-6P 20cm silicon wire

€19.90


€16.45 Ex VAT
Quantity
Matek Micro Power Distribution Board PDB w/ BEC 5V/12V 32X22mm

Matek Micro Power Distribution Board PDB w/ BEC 5V/12V 32X22mm

The Micro PDB has been engineered to provide the highest possible performance and reliability in a 32*22mm & 4 layers PCB. It distributes power from a battery pack to 4 ESCs, as well as providing dual synchronised & regulated DC outputs for powering Cameras, Servos, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc.

It offers a very compact solution to achieve 2A continuous output current over a wide input supply range(3S to 5S LiPo).

Features :

  • 2oz copper & 4-layers PCB
  • ESC & Battery solder tabs in pairs
  • 5V & 12V Output LED indicators & Short circuit tolerant
  • Micro size & lightweight

Specification :

  • Input voltage range (3S-5S operation): 7 - 21V DC
  • Regulated 5V and 12V outputs
  • LED power indicators ( 5V & 12V outputs )
  • 4 ESC outputs

ESC outputs :

  • Continuous current: 20A per output
  • Peak current (10 seconds/minute): 25A per output
  • BEC 5V output :
  • Designed for RC Receivers, Flight controllers, OSD, and Servos
  • DC/DC synchronous buck regulator
  • Voltage: 5.0 +/- 0.1VDC
  • Continuous current: 2 Amps (Max.2.5A 5s/minute)
  • Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
  • Short-circuit tolerant (5 seconds/minute)
  • BEC 12V output :
  • The battery should be 4S~5S LiPo (12.8~21V DC)
  • Standard output designed to power cameras and video transmitters,etc
  • DC/DC synchronous buck regulator, Efficiency is up to 96%
  • Voltage: 12.0 +/- 0.2VDC
  • Output Ripple: 20mV (VIn=16V, VOut=12V@2A Load)
  • Continuous current: 2 Amps (Max.2.5A 5s/minute)
  • Short-circuit tolerant (5 seconds/minute)

BEC 12V @ 3S LiPo :

  • Output voltage= 3S LiPo voltage x 95% Physical:
  • Dimensions: 32 x 22 x 3 mm
  • Weight: 3.5g

€8.90


€7.36 Ex VAT
Quantity
Matek PDB Mini 12V Power Distribution Board uBEC BEC FPV

Matek PDB Mini 12V Power Distribution Board uBEC BEC FPV

This PDB is special used on the FPV Quad copter with 3~4S LiPo.A small PDB board to connect your battery to your esc’s with a built in low drop regulator 12V for your FPV camera. Small and Light. Can power the 12V camera & 12V LED without ripple & noise.

Generally the input voltage of FPV camera is 7~13V,When 4S LiPo is mounted, the linear regulator can power the 12V camera & 12V LED without ripple & noise.

  •     Size: 40*22mm PDB, 3g, Small & Light.
  •     Inbuilt 12V Linear regulator, Cont.500mA
  •     Mounting: 24mm /3mm

 

€4.00


€3.31 Ex VAT
Quantity
Matek WS2812B LED Board With 5V Buzzer For Naze 32 Skyline 32 Flight Controller

Matek WS2812B LED Board With 5V Buzzer For Naze 32 Skyline 32 Flight Controller

Matek WS2812B LED Board With 5V Buzzer For Naze 32 Skyline 32 Flight Controller

When used Naze32, WS2812B LED can show the flight control lock / unlock, about ailerons, brakes, throttle, alarm and other status.
On board 5V active buzzer, after connecting flight control, you can use a remote control switch to trigger it easier to find the plane.

Description:

  • 5050 Package RGB full color highlighting WS2812B lamp beads * 6
  • 5V active buzzer
  • Voltage: 5V (4 ~ 7V)
  • Size: 50 * 10mm, 3g
  • Installation pitch 30.5mm, aperture 3mm

Platform: Arduino, Naze32, Skyline32, SPRacingF3 flight control (need to brush CleanFlight)
When used Naze32, WS2812B LED can show the flight control lock / unlock, about ailerons, brakes, throttle, alarm and other status.
On board 5V active buzzer, after connecting flight control, you can use a remote control switch to trigger it easier to find the plane.

€4.90


€4.05 Ex VAT
Quantity
Power 5 in 1 V3 Distribution Board PDB LED Control 5V BEC, Voltage Alarm Tracker for FPV Multicopter

Power 5 in 1 V3 Distribution Board PDB LED Control 5V BEC, Voltage Alarm Tracker for FPV Multicopter

Matek Power 5 in 1 V3 Distribution Board PDB LED Control 5V BEC, Voltage Alarm Tracker for FPV Multicopter

The 5in1V3 has been engineered to provide the highest possible performance and reliability in a 46*36mm & 4 layers PCB.
It is a 5in1 HUB with Power Distribution Board, BEC 5V/3A &12V/500mA, LED Light Controller, Lost Plane Finder & Low Voltage Alarm functions.
It is specially made for the Multi-Rotors, mini FPV Quad. Built-in 5V BEC can be connected to receiver or flight controller with Aux pins directly.
simplify wiring. The BEC 12V can be used to power the Camera, Video Transmitters,ect. Inbuilt 5V LED light controller, three flash modes can be choosed with the toggle switch of transmiter.
And the buzzer can also be triggered with the toggle switch, which can help you find the models in tall grass or trees.
The 5in1 also acts as a battery voltage monitor.
Once voltage gets below the threshold you set, the buzzer & LED light will remind you.

Specifications:

  • Input voltage range (3S-6S operation): 9 – 26VDC
  • 1 Battery input & 4 ESC outputs
  • Regulated 5V and 12V outputs
  • LED power indicators ( 5V & 12V outputs )
  • 4 pairs 5V LED light pads
  • Low voltage setting value indicators

Includes:

  • 1 x Matek LED & POWER HUB 5in1 V3 Board
  • 1 x cable (100mm)
  • 4 x stand-off (10mm)
  • 4 x stand-off (5mm)
  • 4 x nut
  • 4 x screw
  • Dimensions:46x36x6mm,
  • Weight: 9g
  • Mounting holes 30.5mm square spacing

Features:

  • Built-in 5 functions, small size & light weight
  • 2oz copper & 4-layers PCB.
  • ESC & Battery solder tabs in pairs
  • BEC 5V & 12V Output LED indicators
  • TVS input protection

€13.90


€11.49 Ex VAT
Quantity
RC Vibration Damper Pad Rubber Shock ABSORBER 4pcs

RC Vibration Damper Pad Rubber Shock ABSORBER 4pcs

M3*7+4.5 RC Vibration Damper Pad Rubber Shock Bobbins Absorber with Silicone Based for Matek F405 Flight Controller

€6.00


€4.96 Ex VAT
Quantity
Tail Light WS2812B w/ Loud Buzzer

Tail Light WS2812B w/ Loud Buzzer

Matek Tail Light WS2812B with Loud Buzzer Dual Modes for FPV Racer Multicopters

Designed as an H-Type tail light with 8xWS2812B LEDs and Loud Buzzer.
When used, the WS2812B LEDs can show the flight control lock / unlock, about ailerons, brakes, throttle, alarm and other status.

This product provides dual control modes, it can be controlled either by flight controlling firmwares (Cleanflight, Betaflight,etc.) or by Transmiter.


Specification:

  • Brand name: Matek
  • Item name: LED Tail light with Buzzer board
  • Dual modes: FC control & TX control
  • TX mode: LED 7 colors (White, Red, Green, Blue, Yellow, Magenta, Cyan) LED 5 status (Constant light, Slow blink, Fast blink, Voilent blink)
  • Buzzer: Lost Plane Finder
  • FC mode: support Naze32, SPRacingF3, etc. with CleanFlight or Betaflight firmware
  • Input voltage range: 4.5~5.2V DC
  • Power of TX mode (5V IN ): 1W/0.2A~2W/0.4A Size & mounting: Pls check the Layout
  • Weight: 5g

Package Includes:
1 X LED Tail light with Buzzer board

 

 

€7.50


€6.20 Ex VAT
Quantity