Long range Systems

RFDesign Antenna 868-900MHz 2dBi Monopole (SMA)

868-900MHz quarter wave mono-pole antenna with SMA connector- Pin
This antenna is well suited for airborne UAV/FPV applications due to its light weight and small size

Frequency range: 860-900MHz
Gain: 2.1dBiVSWR: < 1.5
Impedance: 50R
Polarization: Vertical
Weight: 10g
Size: +-51mm long, 8mm diameter

Antenna 868-900MHz 3dBi Dipole (RPSMA)

This antenna is a half wave dipole antennas with a base connector that can swivel up to 90 degrees.   
It is well suited to ground station, or fixed installation applications.  
An additional feature of this type of antenna is reduction of local noise introduced into the antenna from electronics connected to the modem.

868MHz half wave dipole antenna with RPSMA connector.
This antenna is a half wave dipole antennas with a base connector that can swivel up to 90 degrees.   
It is well suited to ground station, or fixed installation applications.  
An additional feature of this type of antenna is reduction of local noise introduced into the antenna from electronics connected to the modem.

Specifications:

• Frequency range: 860-900MHz
• Gain: 3 dBi
• VSWR: < 1.5
• Impedance: 50R
• Polarisation: Vertical
• Size: 175+23mm long, 12mm diameter
• Weight: 28g

Please consult Local Telecom regulations when using this item!

ES900TX and ES900RX modules are a set of Long Range 915MHz/868MHz(optional) wireless transmission equipment developed and designed based on the open source software ExpressLRS. This set of modules is characterized by an ultra-long range, stable operation and low latency. The module is compatible with most Opentx remote controls,, basically plug and play. We specially adapted a heat sink for the transmitter module and also reserved the installation position of the 2006 fan, which can help the transmitter module work stably under high power conditions.

New ES900TX module comes with a 2006 fan, it works automatically when the TX power is 250mW.

Specifications:

ES900TX:

MCU: ESP32+ESP8285

Dimension: 55mm*39mm*11mm

Weight: 9.2 grams (TX module only)

Antenna connector: SMA

VCC input: 5~13v, Recommended 5v~9v

RF frequency optional: 915 MHz or 868 MHz (EU)

Maximum output power: <33dBm (For >27dBm operation we recommend adding a fan for forced cooling)

ES900RX:

MCU: ESP8285

VCC input: 5v

Current operation: ~100Ma

Rx to FC protocol: CRSF

RF frequency optional: 915 MHz or 868 MHz (EU)

Dimension: 12mm*12mm*3mm

Weight: 0.60 grams (excluding antenna)

Antenna connector: IPEX1

Telemetry output power: <17dBm

Download RC7 Firmware for ES900RX:

ExpressLRS RC7 firmware for ES900 RX 915MHz and 868MHz [update via WiFi]

INCLUDED

       1x ES900 TX module 868MHz OR 915

• 1x TX antenna 868MHz/915
• 1x Molding JR Bay mounted case for TX module
• 1x Heat sink
• 1x Adapter wire
• ES900 RX module x1(868MHz or 915MHz optional)
• RX antenna x2

External multi-band L1/L2/E5b helical GNSS antenna, with a weight below 18 grams, ideal for lightweight applications like drones.

– Compatible with all simpleRTK2B boards as well as any other multi band GNSS receiver in the market
– Helical antennas are ideal for GNSS reception in strange attitudes (not always facing the sky)
– Integrates a SMA-male termination, no cable is needed although you can use our cable extenders

Be aware that if you plan to use the Pixhawk connector in the simpleRTK2B board, the helical antenna will block it, so you will need a cable extender.

2B Helical antenna

Antenna element

• Supported positioning signal bands:
  • GPS: L1, L2
  • GLONASS: G1, G2
  • BeiDou: B1, B2
  • Galileo: E1, E5b
  • QZSS: L1, L2
  • SBAS: WAAS, EGNOS, MSAS and GAGAN
• Polarization: RHCP
• Peak gain: 2dBi
• Axial Ratio @ zenith: <3dB
• Azimuth Coverage: 360 degrees
• Impedance: 50 ohm

Electrical

• Supply voltage: 3-16V
• Typical supply current @ 3V: 35mA
• Average LNA gain: 33dB
• Maximum Noise Figure: 1.5dB
• Maximum VSWR: 2

Mechanical

• Maximum length: 56mm
• Weight: 18g
• Mounting style: direct on SMA connector
• Connector: SMA male

Environmental

• Operating Temperature: -40 to +85°C
• Storage Temperature: -40 to +85°C
• IP Rating: IP67
• RoHS: Yes

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today pilots have come to expect.

Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built in FW updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.
Tiny in size yet big on features and range the RP series of receivers have you covered.

What’s new on the RP1

Improved PCB design is better for heat dissipation.
Rigid antenna with greater durability and performance.
Solder pads are improved and easier to solder to.
LED on top side of PCB.

Specifications:

• Item Name: RP1 Nano Receiver- LBT EU protocol
• Type: ISM
• ESP8285 MCU
• SX1280IMLTRT RF Module
• Antenna: 65mm 2.4ghz T Antenna
• Frequency Range: 2400 MHz to 2480 MHz
• Maximum receive refresh rate: 500Hz / F1000Hz
• Minimum receiver refresh rate: 25Hz
• Working voltage: 5v
• Weight: 0.53g (without antenna)
• Dimension: 13mm*11mm*3mm
• TCXO: Yes

Please consult Local Telecom regulations when using this item!

Features

• Based on the Revolutionary ExpressLRS System
• High performance, high reliability, flexible configuration, fast response speed and ultra-long range
• Support 8 PWM Channels
• Optimized ground up PCB design
• Automatically voltage telemetry of external battery voltage or built-in receiver voltage
• ER8GV receiver is built-in high-precision air pressure sensor (Vario)
• Supports Wi-Fi updates and WEBUI configuration
• Reserve 4pin CRSF input port
• High quality 2.54 mm connector
• Standard 15 cm High Sensitivity Antenna
• For fixed-wing aircraft and gliders

Specifications:

• Item: ER8G 2.4GHz ELRS PWM Receiver
• Power supply: DC 3.5 - 8.4V
• Antenna type: 15cm high sensitivity antenna
• Wireless protocol: ExpressLRS 3.3.0 pre-installed
• Output channel: 6CH PWM
• Telemetry power: maximum 50mw (LUA can be set)
• Battery voltage detection range: DC 3.0 - 26V
• Weight: 5.0 grams
• Dimensions:42x13x8mm
• Firmware: Device Category: Radiomaster 2.4Ghz / Device: Radiomaster ER8G

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

Please consult Local Telecom regulations when using this item!

Features

• Based on the Revolutionary ExpressLRS System
• High performance, high reliability, flexible configuration, fast response speed and ultra-long range
• Support 8 PWM Channels
• Optimized ground up PCB design
• Automatically voltage telemetry of external battery voltage or built-in receiver voltage
• ER8GV receiver is built-in high-precision air pressure sensor (Vario)
• Supports Wi-Fi updates and WEBUI configuration
• Reserve 4pin CRSF input port
• High quality 2.54 mm connector
• Standard 20 cm High Sensitivity Antenna
• For fixed-wing aircraft and gliders

Specifications:

• Item: ER8G 2.4GHz ELRS PWM Receiver
• Power supply: DC 3.5 - 8.4V
• Antenna type: 20cm high sensitivity antenna
• Wireless protocol: ExpressLRS 3.3.0 pre-installed
• Output channel: 8CH PWM
• Telemetry power: maximum 100mw (LUA can be set)
• Battery voltage detection range: DC 4.0 - 35V
• Weight: 12 grams
• Dimensions: 60*13.5*13mm
• Firmware: Device Category: Radiomaster 2.4Ghz / Device: Radiomaster ER8G

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series receivers are built-in a TCXO (temperature-compensated crystal oscillator) now, which ensures reliable, stable, and accurate signal reception, allowing for superior performance in demanding environments and enhancing the flight experience.

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today's pilots have come to expect.

The RP1 and RP2 2.4GHz ELRS nano series receivers are open-source receivers based on ExpressLRS. The Nano receivers, first developed by Jye Smith from the ExpressLRS development team, feature ESP8285 MCU and SX1280 RF chip. The RP1 has a UFL antenna socket for full-range antenna use. The RP2 has a built-in ceramic antenna which is super light and small in size and ideal for racing.

The RP1 and RP2 feature WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone.

Due to the low-latency and high-refresh-rate RF module, the RP1 and RP2 are ideal for FPV races or Long Range. Suitable for many models due to the ultra-light and Nano size, these receivers can fit just about anywhere!

Features

• Optimized PCB design for better heat dissipation.
• LNA for better receiver range.
• PA for better telemetry range.
• Antenna Diversity for improved signal stability and range.
• Built-in a TCXO (temperature compensated crystal oscillator)
  
  Specification

Item: RP2 Nano ExpressLRS 2.4ghz Receiver

• Type: ISM
• MCU: EPS8285
• RF Chip: SEMTECH SX1281
• Telemetry RF power: 10mW
• Antenna: On Board SMT Antenna
• Antenna: 65mm 2.4ghz T Antenna
• Frequency Range: 2.404 - 2.479 Ghz
• Maximum receive refresh rate: 500Hz/F1000Hz
• Minimum receiver refresh rate: 25Hz
• Working voltage: 5v
• Weight: 0.55g (On Board antenna)
• Dimension: 13mm*11mm*7mm
• Firmware Version: ExpressLRS v2.4 pre-installed
• FW Target: RadioMaster RP1/2 2400 RX
• Bus interface: CRSF
  
  Package Includes
  
  • 1 * RP2 ExpressLRS 2.4ghz Nano Receiver
  • 1 * User Manual
  • 1 * CRSF wire
    

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series receivers are built-in a TCXO (temperature-compensated crystal oscillator) now, which ensures reliable, stable, and accurate signal reception, allowing for superior performance in demanding environments and enhancing the flight experience.

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today's pilots have come to expect.

Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built-in FW updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.

The RP3 receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mW of telemetry performance and antenna switching for antenna diversity.

Features

• Optimized PCB design for better heat dissipation.
• LNA for better receiver range.
• PA for better telemetry range.
• Antenna Diversity for improved signal stability and range.
• Built-in a TCXO (temperature compensated crystal oscillator)
  
  Specification

• Item: RP3 Diversity Receiver
• Type: ISM
• MCU: ESP8285
• RF Chip: SX1281
• Telemetry RF power: Max 100mw
• Antenna: 65mm 2.4ghz T Antenna x 2
• Frequency Range: 2.404 - 2.479 Ghz
• Maximum receive refresh rate: 500Hz / F1000Hz
• Minimum receiver refresh rate: 25Hz
• Working voltage: 5v
• Weight: 4.6g (Including two antenna)
• Dimension: 22mm*13mm*4mm
• Firmware Version: ExpressLRS v3.0 pre-installed
• FW Target: RadioMaster RP3 Diversity 2400 RX
• Bus interface: CRSF

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

RF Design–TXMOD RFD868 V2 (RC transmitter module) #RF067

***Please contact before ordering, to insure delivery times***

Please check local regulations before Use

The RFDesign TXMOD is an all in one long range telemetry data and RC control system.
Designed to work in conjunction with any Radio Controller capable of accepting JR Transmitter Modules, the RFD TX Module can transmit the PPM stream from the controller to the vehicle via the RFD868x long range telemetry modem while also receiving telemetry data received from the aircraft.
The module’s built in WiFi link allows for simple webpage based configuration and broadcasting of telemetry data to a computer or smart device.
It is a JR style module that plugs into any RC transmitter that has can accept JR style modules (Frsky Taranis, JR, Frsky Horus)
It provides a bridge between the RC transmitter and aircraft while carrying RC PPM data and mavlink telemetry streams at the same time.
 

Features:

Long range using RFD868x telemetry modem

2.4GHz WiFi AP / Client modes with TCP + UDP packet support

Easy configuration by web-based wizard built in

Direct plug in to any RC transmitter with JR style modules (eg. Taranis X9D, Horus, ...)

Wide range 5-18V input supply

Optimised for use with Mavlink/Mission Planner

Applications:

Long range remote control (RC) via PPM

Ground control station (GCS) telemetry gateway over WiFi

Dimensions:

52.05 x 66.94 x 38mm

Delivery scope: TX only

RFD 868+ MHz telemetry Bundle

Long Range telemetry or data-communication Modem-Set the brand RFDesign Pty Ltd.

The Bundle contains all the necessary antennas and cables. Information for commissioning, for example, with the autopilot, the Pixhawk product range can be found here:

ArduPilot Support Radio Modem

Features:

• Long range> 40km depending on antennas and GCS Setup
• 1 Watt (30dBm) transmit power (adjustable up to)
• Low pass filter
20dB low Noise amplifier, high IP3 (updated RFD868+).
• RX SAW Filter.
• All I/O ESD protected and filtered
• The Open Source Firmware SiK (V1.x), field upgradeable, easy to configure.
• Small, light.
• Compatible with 3DR/ Hope-RF Radio modules

Additional Features/ Software:

• Frequency hopping spread spectrum (FHSS)
• Transparent serial connection
• Point-to-point or Multipoint network
• Configuration by simple AT commands for local Radio, RT commands for remote Radio
• User-configurable serial data rates and air data rates
• Error correction routines, Mavlink Protocol frames (user-selectable)
• Mavlink Radio Status Reporting (Local RSSI, Remote RSSI, Local noise, Remote Noise)
• Automatic antenna Diversity switching on a packet basis in real time
• Automatic throttling based on radio temperature to avoid Overheating

Technical Data:

• Frequency Range: 868-869 MHz
• Output power: 1W (30dBm), controllable in 1dB steps (+/- 1dB @ = 20dBm typical)
• Air data transfer rates: 4, 8, 16, 19, 24, 32, 48, 64, 96, 128, 192 and 250 kbit/s (user selectable, 64 kStd)
• +UART-data transfer rates: 9600, 19200, 38400, 57600, 115200, 400k, 921k Baud (user selectable, default 64k)
• Transmit Power: Max. 1W (30dBm)
• Receive sensitivity:> 121 dBm at low data rates, high data rates (TBA)
• Size: 30 mm (wide) x 57 mm (long) x 12.8 mm (thick) - Including RF shield, heatsink and connector-extremities
• Weight: 14.5 g
• Mounting: 3 x M2,5 screws, 3 x header pin solder points
• Power supply: +5 V nominal, (+3.5 V min, +5.5 V max), ~ 800 mA peak at maximum power
• Temp. Range: -40 to +85 ° C, ready for operation 123 ° C tested from -73 to +

Scope of delivery:

• 2 x RFD868+ wireless modem
• 1 x antenna, 868-900MHz quarter wave monopoly 2.1 dBi
• 1 x antenna, 868-900 MHz Right-angle quarter-monopoly 2.1 dBi
• 4 x antennas, 868-900 MHz half-wave dipole 3dBi
• 1 x FTDI USB cable

Software / GCS support:

• The software solution is an Open Source development called "SiK". It has been re-implemented to the new processor architecture to meet the on the 32-Bit ARM processor core available.
• A boot loader and an interface to the further development and on-the-spot Upgrade of the Modem Firmware via the serial interface.

Most of the parameters via AT commands configurable, for example, baud rate (air / Uart), frequency band, power levels.
The built-in support for the configuration of the radio equipment RFD900/RFD868 is supported by APM Planner/ Mission Planner.
The default settings are 57600 Baud, N, 8, 1 and 64 k-air data rate.

NOTE:
Please see with your country Telecommunication rules for using this item, the user is the only respocible for using properly the device.

RFDesign Antenna 868-900MHz 2dBi Monopole (SMA)

868-900MHz quarter wave mono-pole antenna with SMA connector- Pin
This antenna is well suited for airborne UAV/FPV applications due to its light weight and small size

Frequency range: 860-900MHz
Gain: 2.1dBiVSWR: < 1.5
Impedance: 50R
Polarization: Vertical
Weight: 10g
Size: 51mm long, 8mm diameter

RF Design RFD 868+ Radio Modem- please check local regulations before use

RFD868x New Features:

• New Processor, ARM 32 bit core.
• Air data rate: 250bit/s.
• RC PPM Passthrough with telemetry at the same time.
• Fully ESD protected + filtered – Every IO port is protected and filtered.
• Original SiK point to point firmware implemented.
• Note: Currently due to the bandwidth limitations of the 868 modems Asynchronous Mesh and Multipoint Firmware are not officially supported for the 868X modems and correct operation of this code cannot be guaranteed

Features:

• Long range >20km depending on antennas and GCS setup *80km demonstrated by Edge Research labs on a balloon !, 57km in India, on Dipoles.
• 2 x RP-SMA RF connectors, diversity switched.
• up to 1 Watt (+30dBm) transmit power. adjustable 0 to 30dBm in 1dBm steps – ensure you comply with all local regulations.
• Transmit low pass filter.
20dB Low noise amplifier, high IP3.
• RX SAW filter.
• All I/O ESD protected and filtered.
• Re implemented SiK and Multipoint SiK firmware, field upgradeable, easy to configure.
• Small, light weight.
• Note: Not compatible with older modems

Interfaces:

• RF : 2 x RP-SMA connectors
• Serial: Logic level TTL (+3.3v)
• Power: +5v, ~800mA max peak (at maximum transmit power)
• GPIO: 6 General purpose IO (Digital, ADC, PWM capable).

Specifications:

• Frequency Range:  868-869 MHz
• Output Power: 1W (+30dBm), controllable in 1dB steps ( +/- 1dB @=20dBm typical )
• Air Data transfer rates: 4, 8, 16, 19, 24, 32, 48, 64, 96, 128, 192 and 250, 500 kbit/sec ( User selectable, 64k default )
• UART data transfer rates: 9600, 19200, 38400, 57600, 115200, 400k, 921k baud  ( User selectable, 57600 default )
• Output Power: 1W (+30dBm)
• Receive Sensitivity: >121 dBm at low data rates, high data rates (TBA)
• Size: 30 mm (wide) x 57 mm (long) x 12.8 mm (thick) – Including RF Shield, Heatsink and connector extremeties
• Weight: 14.5g
• Mounting: 3 x M2.5 screws, 3 x header pin solder points
• Power Supply: +5 V nominal, (+3.5 V min, +5.5 V max), ~800 mA peak at maximum power
• Temp. Range: -40 to +85 deg C, tested operational from -73 to +123 deg C.

Software / GCS Support:

• The software solution is an open source development called “SiK”.  It has been re implemented to suit the new processor architecture available on the 32bit ARM processor core.  
• A boot loader and interface is available for further development and field upgrade of the modem firmware via the serial port.
• Most parameters are configurable via AT commands, Eg. baud rate (air/uart), frequency band, power levels.
• Integrated support for configuring the RFD900 radios is supported by APM Planner.
• The default settings are at 57600 baud, N, 8, 1, and 64k air data rate.
• The RFD868/900x manual is here: RFD900x Manual
• The RFD868/900x SiK software manual is here : RFD900x Peer-to-peer Manual

Software features include:

• Frequency hopping spread spectrum (FHSS)
• Transparent serial link
• Point to Point, or Multipoint networking
• Configuration by simple AT commands for local radio, RT commands for remote radio
• User configurable serial data rates and air datarates
• Error correction routines, Mavlink protocol framing (user selectable)
• Mavlink radio status reporting (Local RSSI, Remote RSSI, Local Noise, Remote Noise)
• Automatic antenna diversity switching on a packet basis in realtime
• Automatic duty cycle throttling based on radio temperature to avoid overheating

Compliance :

• The RFD868 is designed to be compliant with the following standards:
• FCC Part 15.247 (Frequency hopping and digitally modulated intentional radiators)
• AS/NZS 4268:2012 (Radio equipment and systems – short range devices)
• The modem is designed for system integrators who will integrate the modem into their own projects and product prototypes.  
• The user is responsible for compliance with local regulations for radio transmitters.

RF Design RFD 868+ Radio Modem- please check local regulations before use

RFD868x New Features:

• New Processor, ARM 32 bit core.
• Air data rate: 500kbit/s.
• AES Hardware accelerated encryption. *Fully working*
• RC PPM Passthrough with telemetry at the same time.
• Fully ESD protected + filtered – Every IO port is protected and filtered.
• Original SiK point to point firmware implemented.
• Note: Currently due to the bandwidth limitations of the 868 modems Asynchronous Mesh and Multipoint Firmware are not officially supported for the 868X modems and correct operation of this code cannot be guaranteed

Features:

• Long range >40km depending on antennas and GCS setup *80km demonstrated by Edge Research labs on a balloon !, 57km in India, on Dipoles.
• 2 x RP-SMA RF connectors, diversity switched.
• up to 1 Watt (+30dBm) transmit power. adjustable 0 to 30dBm in 1dBm steps – ensure you comply with all local regulations.
• Transmit low pass filter.
20dB Low noise amplifier, high IP3.
• RX SAW filter.
• All I/O ESD protected and filtered.
• Re implemented SiK and Multipoint SiK firmware, field upgradeable, easy to configure.
• Small, light weight.
• Note: Not compatible with older modems

Interfaces:

• RF : 2 x RP-SMA connectors
• Serial: Logic level TTL (+3.3v)
• Power: +5v, ~800mA max peak (at maximum transmit power)
• GPIO: 6 General purpose IO (Digital, ADC, PWM capable).

Specifications:

• Frequency Range:  868-869 MHz
• Output Power: 1W (+30dBm), controllable in 1dB steps ( +/- 1dB @=20dBm typical )
• Air Data transfer rates: 4, 8, 16, 19, 24, 32, 48, 64, 96, 128, 192 and 250, 500 kbit/sec ( User selectable, 64k default )
• UART data transfer rates: 9600, 19200, 38400, 57600, 115200, 400k, 921k baud  ( User selectable, 57600 default )
• Output Power: 1W (+30dBm)
• Receive Sensitivity: >121 dBm at low data rates, high data rates (TBA)
• Size: 30 mm (wide) x 57 mm (long) x 12.8 mm (thick) – Including RF Shield, Heatsink and connector extremeties
• Weight: 14.5g
• Mounting: 3 x M2.5 screws, 3 x header pin solder points
• Power Supply: +5 V nominal, (+3.5 V min, +5.5 V max), ~800 mA peak at maximum power
• Temp. Range: -40 to +85 deg C, tested operational from -73 to +123 deg C.

Software / GCS Support:

• The software solution is an open source development called “SiK”.  It has been re implemented to suit the new processor architecture available on the 32bit ARM processor core.  
• A boot loader and interface is available for further development and field upgrade of the modem firmware via the serial port.
• Most parameters are configurable via AT commands, Eg. baud rate (air/uart), frequency band, power levels.
• Integrated support for configuring the RFD900 radios is supported by APM Planner.
• The default settings are at 57600 baud, N, 8, 1, and 64k air data rate.
• The RFD868/900x manual is here: RFD900x Manual
• The RFD868/900x SiK software manual is here : RFD900x Peer-to-peer Manual

Software features include:

• Frequency hopping spread spectrum (FHSS)
• Transparent serial link
• Point to Point, or Multipoint networking
• Configuration by simple AT commands for local radio, RT commands for remote radio
• User configurable serial data rates and air datarates
• Error correction routines, Mavlink protocol framing (user selectable)
• Mavlink radio status reporting (Local RSSI, Remote RSSI, Local Noise, Remote Noise)
• Automatic antenna diversity switching on a packet basis in realtime
• Automatic duty cycle throttling based on radio temperature to avoid overheating

Compliance :

• The RFD868 is designed to be compliant with the following standards:
• FCC Part 15.247 (Frequency hopping and digitally modulated intentional radiators)
• AS/NZS 4268:2012 (Radio equipment and systems – short range devices)
• The modem is designed for system integrators who will integrate the modem into their own projects and product prototypes.  
• The user is responsible for compliance with local regulations for radio transmitters.
  
  Delivery contains: 1 unit of 868xRadio Modem

If you’re tired of antennas that promise the world but deliver only a pond, it’s time to upgrade to the S-conn 868-900Mhz Rubber Duck Antenna. It’s not just an antenna; it’s a beacon of reliability, efficiency, and environmental responsibility. Perfect for the discerning enthusiast who understands that in the world of telemetry, only the best will do

This antenna is well suited for airborne UAV/FPV applications due to its light weight and small size

Frequency range: 860-900MHz
Gain: 3 dBi
Impedance: 50 ohm
Polarization: Vertical
Weight: 10g
Size: +-51mm long, 8mm diameter
Connector type- RP-SMA

If you’re tired of antennas that promise the world but deliver only a pond, it’s time to upgrade to the S-conn 868-900Mhz Rubber Duck Antenna. It’s not just an antenna; it’s a beacon of reliability, efficiency, and environmental responsibility. Perfect for the discerning enthusiast who understands that in the world of telemetry, only the best will do

This antenna is well suited for airborne UAV/FPV applications due to its light weight and small size

Frequency range: 860-900MHz
Gain: 3 dBi
Impedance: 50 ohm
Polarization: Vertical
Weight: 10g
Size: +-51mm long, 8mm diameter
Connector type- SMA

If you’re tired of antennas that promise the world but deliver only a pond, it’s time to upgrade to the S-conn 868-900Mhz Rubber Duck Antenna. It’s not just an antenna; it’s a beacon of reliability, efficiency, and environmental responsibility. Perfect for the discerning enthusiast who understands that in the world of telemetry, only the best will do

This antenna is well suited for airborne UAV/FPV applications due to its light weight and small size

Frequency range: 860-900MHz
Gain: 3 dBi
Impedance: 50 ohm
Polarization: Vertical
Weight: 10g
Size: +-51mm long, 8mm diameter
Connector type- RP-SMA

If you’re tired of antennas that promise the world but deliver only a pond, it’s time to upgrade to the S-conn 868-900Mhz Rubber Duck Antenna. It’s not just an antenna; it’s a beacon of reliability, efficiency, and environmental responsibility. Perfect for the discerning enthusiast who understands that in the world of telemetry, only the best will do

This antenna is well suited for airborne UAV/FPV applications due to its light weight and small size

Frequency range: 860-900MHz
Gain: 3 dBi
Impedance: 50 ohm
Polarization: Vertical
Weight: 10g
Size: +-51mm long, 8mm diameter
Connector type- RP-SMA

Supports dual HDMI 1080P 60fps video input, which can be modified through the QGC interface.
Dual S.bus signal output for simultaneous control of autopilot and pan/tilt cameras.
The integrated digital transmission and image transmission can simultaneously transmit the flight data of the autopilot and the image output by the camera  to the remote controller.
Built-in QGC open source ground station with adaptable apm and px4 firmware for direct flight function.
Independent Mavlink commands camera buttons and scroll wheel channels.
Custom channel button and PWM value assignment.

Technical specifications

Air Unit and Controller hardware information:

Processor: SoC – Pinecone S1 AP: 4 x large core, Cortex A53, 2.2GHz 4 x small core, Cortex A53, 1.4GHz GPU: 4 core, Mali-
T860 SDR: A7 + DSP Storage: Sky: LPDDR3: 1GB Ground: LPDDR3: 2GB Sky / Ground: EMMC: 4GB
Transmission Distance: FCC 20km CE / SRRC 12km Image transmission delay: ≤ 110ms Image transmission: 720p@30fps 1080p@30 / 60fps transmission
Frequency Band: 2.4GHz ISM Receive sensitivity: -99dBm@20MHz BW Interference recovery: < 1s

Air Unit:

Appearance: core board + video daughter board + structure of RF daughter board
Among them, the video daughter board completes the input bridge function of theHDMI signal.
The RF daughter board completes the function of transmitting and receiving signals
M2 (E) connector connection between daughter board and core
Size: 78.5x30x13mm
Micro HDMI x 2: Input for external camera video signals
2 Pin interface x 1:5V-12V power input interface
3 Pin interface x 1:3.3V / 5V level UART interface
4 Pin interface x 1 : Two 3.3V level RC output connectors (S.bus in phase, S.bus inverting or PPM signal output, ground terminal control)
Micro USB x 1: for debugging upgrades, support OTG mode
Keyhole x 1: for frequency and status reset
Indicator x 2: used to indicate the frequency and picture status
MMCX antenna jack x 2: used for signal transmission and ground communication
Signal bandwidth: 20MHz / 10MHz
Power consumption: the average power consumption of the single-sided module is less than 4W

Controller:

Housing: plastic
Dimensions: 217 × 106.5 × 31mm (the whole machine does not contain external antenna and rocker)
Screen: 5.46 inch, 1080P, 16 million colors, capacitive touch screen
Audio: Built-in speaker × 1, built-in microphone × 2
Remote control: rocker × 2, scroll wheel × 1, bottom button × 6, with backlight, top button × 1 (right)
Communication : BT / WIFI / GPS 2.4G map transmission ground
Indicator light: Top tri-color lamp × 2 (left, right)
Interface: MicroUSB×1, TFlash×1 (supports maximum 64G expansion)
Antenna: Orientation (5dBi) × 1 detachable, omnidirectional (2dBi) × 1 detachable
Built-in wifi antenna, built-in GPS antenna, external GPS antenna interface
Power : Built-in 4950 mAh Lipo Battery
Charging : Support micro USB port 5v 2A current charging
Power consumption: The average power consumption does not exceed 4W (only picture transmission work, medium screen brightness, WiFi off, GPS off)

• Build in high efficiency antenna to avoid delay in digital transmission. For safety flying
• Build in intelligent communication. Increase the stability of long distance transmission. Dual antenna dual module
• Supported by FHSS technology. The longer distance can reach 20km
• Hall sensor gimbal with permanent magnetic sensor make longer life to 30 years. Military grade anti dust protective gimbal cover
• Remote dimming camera with &w LED can capture video clearly at night
• Bluetooth plus USB wire provide reliable link up
• 24hrs continues working with one charge
• Legal 100mw output power comply with related certificate for export
• Battery is MSDS certified so it is allowable to carry on the plane

Item name: T12 Transmitter
Number of channels: 12 channels
Frequency: 2.400-2.4833GHz
Working voltage: 3.7V(1s Li-ion)
Working Current: 130mA
Modulation: New FHSS
Weight: 560g
Firmware: APP online
Dimension: 225*123*35mm
Duration: 25 hours
Battery Capacitor: 4000mA
Charge Port: MICRO-USB
Application: Helicopter,Fixed wing,Quadcopter,car boat

R12 Receiver:

Model: R12
Number of channels: 12 channels
Working voltage: 4.5-5.5v
Working Current: 140mA@5V
Dimension: 51*41*13MM
Weight: 14g

Package Included:

• 1 x T12 Transmitter
• 1 x R12 Receiver