A set of components for the outlet and fixing the fuel hose pipe and KAVAN Rechargeable Pump to the jerry can.

Airplane wing Nylon screw M6x40

Set of 2 Screws.

These are GREAT working pliers! Soft grip handle, curved end of jaws, spring loaded open.
Not only the best we've used, also the best value!

High quality chrome vanadium steel material , Slip-resistant handle, easy to hold it and operate.
Suits for RC helicopter DIY

Specifications:
Material: Chrome vanadium steel

Fastrax Kavan Glow Clip 33.5mm With Banana Plugs

Muffler/header adapter joiner. made from High temp- Silicone, resistant to 250C

Muffler Tube dimensions: 20x3mm , 10cm long

KAVAN Hand crank fuel pump for Nitro- Gas

Hand Fuel Pump for quick clean and easy fueling. Will fill or drain. Complete with fittings

Special TPR material provides a comfortable feel, while an improved gear mesh and overdrive create the large flow rate of 18cc a second.
The advanced pump unit design is compatible with both glow and gasoline fuels and it comes complete with filter nozzle and silicone fuel tubing.

Specifications:

• Dimensions (approximately): 105mm x 52.5mm x 60mm
• New generation fuel pump with compact size
• Double injection, using TPR material that has a comfortable feel
• Improved gear mesh and make the large flow rate 18cc/sec
• Advanced pump unit design, glow fuels and gasoline are both compatible
• Includes filter fuel nozzle and  silicon fuel tubing

Kavan Original Cotton Sock For Sealing Iron / Iron Cotton Cover / Protective Cover

Sock 1 pcs, Iron is not included

Almost ready to fly semi-scale model (1500 mm wingspan) of a Swiss STOL utility aeroplane. Made of carbon-reinforced expanded polyolefin (EPO); KAVAN C3548-750 brushless motor, 10x6” three blade prop, R-40SB ESC and 6 micro servos installed. “Full house“ aileron, flap, elevator, rudder and throttle control; steerable tail wheel/water rudder, LED lights. For 4S LiPo 2600–3300mAh (at least 30C) battery

The single-engine Swiss STOL utility aircraft Pilatus PC-6 Porter, originally powered by the Lycoming flat six cylinder engine, made its maiden fight in 1959. Soon an improved Turbo-Porter powered by a turboprop engine followed. Over the years Turbomeca Astazou II, Garret Air Research TPE 331 and ultimately Pratt & Whittney Canada PT6A (about 70% of all PC-6 ever produced) turboprops have been taking this beautiful plane to the sky.

Incredible, almost helicopter-like short takeoff and landing capabilities have quickly gained attention of military as well as commercial operators. Fitted with wheeled undercarriage, skis or floats, Porters have been serving reliably and relentlessly all over the world - flying over deserts, jungles, lakes, mountains, snow and ice - simply everywhere. No wonder the PC-6 holds the world record for highest landing by a fixed-wing aircraft, at 18,865 feet (5,750 m), on the Dhaulagiri glacier in Nepal.

After 604 deliveries in 63 years, Pilatus ended production in 2022... And now you can enjoy flying with our 1500 mm wingspan semi-scale model of this beautiful sailplane powered by a brushless motor.

The EPO foam fuselage, thoroughly carbon-reinforced, comes with the KAVAN C3548-750 brushless motor, 10x6” three blade propeller and KAVAN R-40SB ESC featuring a powerful switching SBEC stabilizer necessary to feed all 6 servos aboard. The battery compartment (under a removable hatch in the nose) offers a lot of space for your flight pack.

The two-piece EPO wing is reinforced by carbon spars and joined together with a carbon tube joiner. The wing is secured by bolts to the fuselage. The ailerons and flaps are controlled by two pairs of servos installed in the wing driven with short wire push rods; there are position and landing LED lights installed as well. The easy-to-install carbon wing struts are secured with a pair of wire clips.

The empennage is made of the EPO foam. The elevator servo is installed in the fuselage, the rudder servo is installed in the fin.

The main undercarriage has steel wire legs with scale telescopic struts; the steel wire tailwheel is coupled with the rudder. You can purchase an optional floats set for your Porter - installation of the floats and water rudder is a matter of minutes.

PC-6 is powered by the KAVAN C3548-750 brushless motor with the KAVAN R-40SB 40A ESC.

You will need 14.8 V 2600-3300 mAh flight pack (at least 30C) to fly your Porter.

Wing span [mm] 1500
Length [mm] 1112
Wing surface [dm2] 27.9
Weight [g] 1650 - 1700
Build difficulty - Easy

ARTF set contents
EPO fuselage with the brushless motor, 40A ESC,
10x6" 3-blade propeller and servos installed
EPO wing with 4 servos and LED lights installed,
EPO horizontal tail plane, undercarriage and instruction manual.

Advanced 24-channel RC set Twin 2.4GHz/ACCST D16/ACCESS. Ergonomic robust body, precision gimbals with Hall sensors. Full telemetry support, large color touch screen with intuitive user interface. ETHOS™ operating system. Extensive range of functions and mixes for all types of RC models. KAVAN servo programming. Support for telemetry receivers with classic PWM and S.BUS outputs.

Exactly according to preference

The rigorously CNC-machined aluminum gimbals are mounted on 10 ball bearings. Hall sensors instead of conventional potentiometers sense the movement of the sticks. This makes the control more precise and reliable. You can also customize the controllers to your own preferences. Easily adjust the length of the sticks, rotate the gimbals up to 8°, and limit the range of stick travel to 45° to 60°.

Comfortable and stylish

Looks matter. Comfort matters even more. The gimbals are closer to the edges of the transmitter body for a comfortable and secure grip. Both handheld and when using the. Switches, buttons, dials and trims are always within reach. So you don't have to take your eyes off your model for a second. But the stylish and vigorous exterior of the transmitter tempts you to do so.

Don't get jammed

The 2.4GHz simultaneous dual-frequency transmission system communicates simultaneously with both the receiver and the RF module. The two built-in 2.4GHz antennas have greater omnidirectional coverage for the transmitted signal compared to a single antenna. This makes the transmission uninterrupted and has a rapid response time of under 4 ms. Data (including telemetry) will flow safely to you over several kilometers.

Touch the colors

The large color touchscreen has a resolution of 800×480 px on a 4.3" diagonal. It displays the ETHOS™ operating system environment. With adjustable display brightness, you won't get lost in the dark or directly under the sun. Intuitively, clearly, and most importantly, conveniently set up or display everything from basic telemetry to advanced mixes and curves directly in the transmitter. You can even choose the colour scheme or turn on dark mode and read everything in English or many other languages

Connectivity for an easier life

Use the USB serial port for data transfer, battery charging, and even if you want to fly the simulator. And because it's USB-C, you always plug it in on the first try. Of course, there's also a trainer port, headphone jack or microSD card slot. Besides audio or voice alerts, you can also activate vibration feedback.

Plugging in a single connector is more elegant than searching for identical (and charged) batteries. The included 2S LiPo 4000mAh battery provides 6.5–8.4V power. It can be safely charged with a USB-C cable thanks to the built-in balancer. No need to remove it from the case. The available timer and warning signals take care of early warning of running out of power.

Advanced 24-channel RC set Twin 2.4GHz/ACCST D16/ACCESS. Ergonomic robust body, precision gimbals with Hall sensors. Full telemetry support, large color touch screen with intuitive user interface. ETHOS™ operating system. Extensive range of functions and mixes for all types of RC models. KAVAN servo programming. Support for telemetry receivers with classic PWM and S.BUS outputs.

Exactly according to preference

The rigorously CNC-machined aluminum gimbals are mounted on 10 ball bearings. Hall sensors instead of conventional potentiometers sense the movement of the sticks. This makes the control more precise and reliable. You can also customize the controllers to your own preferences. Easily adjust the length of the sticks, rotate the gimbals up to 8°, and limit the range of stick travel to 45° to 60°.

Comfortable and stylish

Looks matter. Comfort matters even more. The gimbals are closer to the edges of the transmitter body for a comfortable and secure grip. Both handheld and when using the. Switches, buttons, dials and trims are always within reach. So you don't have to take your eyes off your model for a second. But the stylish and vigorous exterior of the transmitter tempts you to do so.

Don't get jammed

The 2.4GHz simultaneous dual-frequency transmission system communicates simultaneously with both the receiver and the RF module. The two built-in 2.4GHz antennas have greater omnidirectional coverage for the transmitted signal compared to a single antenna. This makes the transmission uninterrupted and has a rapid response time of under 4 ms. Data (including telemetry) will flow safely to you over several kilometers.

Touch the colors

The large color touchscreen has a resolution of 800×480 px on a 4.3" diagonal. It displays the ETHOS™ operating system environment. With adjustable display brightness, you won't get lost in the dark or directly under the sun. Intuitively, clearly, and most importantly, conveniently set up or display everything from basic telemetry to advanced mixes and curves directly in the transmitter. You can even choose the colour scheme or turn on dark mode and read everything in English or many other languages

Connectivity for an easier life

Use the USB serial port for data transfer, battery charging, and even if you want to fly the simulator. And because it's USB-C, you always plug it in on the first try. Of course, there's also a trainer port, headphone jack or microSD card slot. Besides audio or voice alerts, you can also activate vibration feedback.

Plugging in a single connector is more elegant than searching for identical (and charged) batteries. The included 2S LiPo 4000mAh battery provides 6.5–8.4V power. It can be safely charged with a USB-C cable thanks to the built-in balancer. No need to remove it from the case. The available timer and warning signals take care of early warning of running out of power.

Small Rechargeable  fuel pump for petrol and methyl alcohol fuel. Flow rate up to 1300 ml / min, endurance 15 minutes per one charge. The pump contains a Li-ion battery, allows charging via a micro USB cable from a USB source 5V / 1A

SPECIFICATION:
- Flow rate [ml/min] 1300
- Fuel / Petrol (gasoline), Glow Fuel (“Nitro“)
- Battery 2000 mAh Li-ion
- Battery Duration Up to 15 min continual operation
- Charge Voltage 5.0 V
- Charge Current 1.0 A
-Charge Connector USB Micro B
- Dimensions [mm] 27X136
- Weight [g] 153

USING THE PUMP
1. Please charge the battery before use.
2. Connect the supplied micro USB charging cable to the charge socket on your pump; the other end is to be connected to 5V/1A USB wall charger or PC USB port. The indicator LED will light up. When the battery is fully charged, the LED indicator goes off; please dis-connect the charging cable. If the LED indicator starts flashing it means the battery is old and needs replacement. Please contact your KAVAN distributor to change the internal battery
3. Choose proper tubing according to the fuel used - never use silicone tubing for petrol (gasoline)! Connect the tubing (needs to be purchased separately) to the input and output nipples.
4. Please connect a fuel filter at the fuel container (input) side. Pump life will be shortened and performance reduced if dirt is sucked into the pump.
5. Use the ON/OFF switch to fill or drain fuel. Center position of the switch is OFF, both up and down position is ON (up position: continuous operation; down position: momentary operation).

CAUTION:
- Charge prior use.
- Do not operate more than 5 seconds without fuel.
- Always use a filter on the fuel container side.
- Do not modify or disassemble the pump.
- Do not use the pump for aggressive/corrosive liquids.
- Do not immerse the pump in water or other liquid

KAVAN Spinner 50mm black #KAV0046.2

A low cost fully featured power panel with adjustable glow plug current and ammeter. Supplied with battery connectors and leads plus matching banana plugs for your glow clip, fuel pump and starter.

Suitable for installation in a start box as a central supply and switching point:

• 12V for connection of the e-starter or. Craft pump
• Single-off/on switch for pump
• continuously adjustable Glow plug power current with display
• A 12 V battery of corresponding capacity is required for power.
• Pump not included
  

Multi-Function Power Panel w/pump, Glow Clip Out With Current Adjust, 12v Starter Out

Basic features:

• Powered by 12V battery
• 1.5V spark plug glow output with smooth current regulation, meter and switch
• built-in fuel pump with direction switch (filling/draining) for methanol-based fuels
• 12V output for starter
• included: 3 pairs of banana connectors (black and red for all panel connectors) and one pair of crocodile clips

KAVAN high-quality wooden propellers were constructed with the help of the latest software and are produced using the newest and most advanced CNC machines.

Their profile and shape are optimized to ensure high efficiency throughout the range of operating speeds.

The unique shaping of the leaf ends contributes to achieving low noise propellers. Whether you mount them on a "glow plug" or "gasoline" your KAVAN propeller is your choice to "hold" your aerobatic model or dummy in the air! KAVAN propellers are designed and manufactured in the Czech Republic.

Advanced 6-channel 2.4GHz telemetry receiver for ACCESS and ACCST D16 RC protocols, with 6 high-precision PWM channels and 16 or 24-channel S.BUS modes. Two detachable antennas with IPEX4 connector provide full signal strength throughout the range. It's especially ideal for gliders, but you can use it for various other models as well. Thanks to its size and low weight, it is also suitable for small models. With redundancy support, it can be connected as a primary receiver via S.BUS. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices.

It features advanced anti-interference protection for reliable and stable signal transmission across the entire range. Smart-match system speeds up pairing. The black box function preserves basic flight data. LED indicates the receiver's operating status. A Smart matching function allows firmware updates wireless.

Features:

• Increased protection against RF interference and more stable RF transmission
• ACCESS and ACCST D16 RC protocols with smart pairing
• Basic black box function support
• 6 high-precision PWM channels
• S.BUS output port（with 16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• Full-range telemetry (S.Port or F.BUS)
• Wireless firmware updates (OTA)
• External battery/device voltage detection

Technical Specifications:

• Dimensions: 33×15×9.7 mm (L×W×H)
• Weight: 4.2 g
• Number of channels: 6 PWM channels + 16/24 channel mode via S.BUS
• Operating voltage range: 3.5–10 V
• Operating current: ＜65 mA at 5 V
• Operating range: ＞2 km (full range, may vary according to actual ambient conditions)
• External voltage measurement range via AIN2: 0-35 V (battery voltage divider ratio: 1:10)
• Antenna connector: IPEX4
• Compatibility: 2.4GHz ACCESS / ACCST D16 transmitters

Advanced 6-channel 2.4GHz telemetry receiver for ACCESS and ACCST D16 RC protocols, with 6 high-precision PWM channels and 16 or 24-channel S.BUS modes. Two detachable antennas with IPEX4 connector provide full signal strength throughout the range. It's especially ideal for gliders, but you can use it for various other models as well. Thanks to its size and low weight, it is also suitable for small models. With redundancy support, it can be connected as a primary receiver via S.BUS. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices.

It features advanced anti-interference protection for reliable and stable signal transmission across the entire range. Smart-match system speeds up pairing. The black box function preserves basic flight data. LED indicates the receiver's operating status. A Smart matching function allows firmware updates wireless.

It is equipped with a variometer that provides more accurate and faster measurement and transmission of altitude and vertical speed data. It also allows quick audio feedback from the variometer to the ACCESS transmitters.

Features:

• Increased protection against RF interference and more stable RF transmission
• ACCESS and ACCST D16 RC protocols with smart pairing
• Basic black box function support
• 6 high-precision PWM channels
• S.BUS output port（with 16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• Full-range telemetry (S.Port or F.BUS)
• Wireless firmware updates (OTA)
• External battery/device voltage detection

Technical Specifications:

• Dimensions: 33×15×9.7 mm (L×W×H)
• Weight: 4.2 g
• Number of channels: 6 PWM channels + 16/24 channel mode via S.BUS
• Operating voltage range: 3.5–10 V
• Operating current: ＜65 mA at 5 V
• Operating range: ＞2 km (full range, may vary according to actual ambient conditions)
• External voltage measurement range via AIN2: 0-35 V (battery voltage divider ratio: 1:10)
• Antenna connector: IPEX4
• Compatibility: 2.4GHz ACCESS / ACCST D16 transmitters

Advanced 8-channel 2.4GHz simultaneous dual-frequency Twin 2.4GHz telemetry receiver. It has 8 high-precision PWM channels and 16 or 24-channel modes via S.BUS. Two detachable antennas with IPEX4 connector provide full signal strength over a range of up to tens of kilometers. It is especially ideal for gliders, but you can also use it for other various models. With redundancy support, it can be connected as a primary receiver via S.BUS. With the Twin 2.4GHz protocol, both receivers work fully simultaneously in this setup. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices, providing bidirectional data transmission via a single cable.

It features advanced interference suppression for reliable, stable signal transmission across the entire range. Smart transmission system matching speeds up pairing. The black box function stores essential flight data. Receiver operating statuses are indicated by an LED indicator. Smart pairing allows firmware updates wireless.

Features:

• Increased protection against RF interference and more stable RF transmission
• Simultaneous Twin 2.4GHz dual frequency transmission system with smart pairing
• Black box function
• High maximum operating range
• Wireless firmware updates (OTA)
• 8 high-precision PWM channels
• S.BUS output port (16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• F.BUS / S.Port

Technical specifications:

• Frequency: simultaneous dual 2.4 GHz
• Dimensions: 54×20×10 mm (L*W*H)
• Weight: 9.8 g
• Operating voltage: 3.5–10 V (supply voltage min. 2.8 V).
• Operating current: 80 mA at 5 V
• External voltage measurement range via AIN2: 0–35 V
• Antenna connector: IPEX4
• Compatibility: 2.4 GHz dual-frequency simultaneous transmission system

Advanced 8-channel 2.4GHz simultaneous dual-frequency Twin 2.4GHz telemetry receiver. It has 8 high-precision PWM channels and 16 or 24-channel modes via S.BUS. Two detachable antennas with IPEX4 connector provide full signal strength over a range of up to tens of kilometers. It is especially ideal for gliders, but you can also use it for other various models. With redundancy support, it can be connected as a primary receiver via S.BUS. With the Twin 2.4GHz protocol, both receivers work fully simultaneously in this setup. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices, providing bidirectional data transmission via a single cable.

It features advanced interference suppression for reliable, stable signal transmission across the entire range. Smart transmission system matching speeds up pairing. The black box function stores essential flight data. Receiver operating statuses are indicated by an LED indicator. Smart pairing allows firmware updates wireless.

It is equipped with a variometer that provides more accurate and faster measurement and transmission of altitude and vertical speed data. It also allows quick audio feedback from the variometer to the Twin 2.4GHz transmitters.

Features:

• Increased protection against RF interference and more stable RF transmission
• Simultaneous Twin 2.4GHz dual frequency transmission system with smart pairing
• Black box function
• High maximum operating range
• Wireless firmware updates (OTA)
• 8 high-precision PWM channels
• S.BUS output port (16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• F.BUS / S.Port

Technical specifications:

• Frequency: simultaneous dual 2.4 GHz
• Dimensions: 54×20×10 mm (L*W*H)
• Weight: 9.8 g
• Operating voltage: 3.5–10 V (supply voltage min. 2.8 V).
• Operating current: 80 mA at 5 V
• Vario - vertical speed measurement range: ±10 m/s
• Vario - altimeter range and resolution: -700 m to 10,000 m, 0.1 m
• External voltage measurement range via AIN2: 0–35 V
• Antenna connector: IPEX4
• Compatibility: 2.4 GHz dual-frequency simultaneous transmission system

High temp- Silicone tube, dimensions are 8mm ID, 16mm OD

20cm long, if you need longer lengths please ask us

Muffler/header adapter joiner. made from High temp- Silicone

Muffler Tube dimensions: 20x30mm ,5mm wall thickness 20 cm long

Color Dark Gray