Castle Creations

Programs your controllers without a computer (mostly).
Works as a standard Castle Link USB adapter with your computer.

Sometimes you need to make a change in the programming of a Castle controller and you just don't happen to have a laptop in your man purse. What to do? There's always the old stick programming method that we all love to hate. Yes it works, but...  there has to be a better way. Now there is Field Link!

Field Link allows you to modify the most commonly used settings in your Castle controller all at the touch of a single button. No computer needed (mostly). Simply connect the Field Link to the throttle lead of the controller and power the pair as described below. Click the button to scroll through and change the indicated settings. Can't get any easier!

Castle Creations - Castle Link V3 USB Programming Kit

Program your Castle brushless ESCs and accessories on your Windows® PC with the Castle Link USB programming kit.

• Set up of programmable options with point and click ease
• View your current program settings
• Air users can customize values for low-voltage cutoff, prop brake strength, governor gain and more
• Surface users can customize values for low-voltage cutoff, drag brake, torque limiting and more
• Download new software updates as they become available

Simple programming interface featuring:

• All-in-one support for all Phoenix, Talon, Thunderbird, QuadPack, DMR, Mamba, Sidewinder, and Hydra controllers, as well as accessories like Telemetry Link, as well as all of our external switching regulators (BECs).
• Demo Mode allows users to check available settings without connecting their Castle device to the computer
• Simple to install software
• Expanded programming and parameters for all Castle ESCs

Set-up instructions:

• Download the interface software from the Software area.
• Plug the Castle Link into the receiver lead on your controller and attach the micro USB cable included in the kit.
• Connect the USB cable to your PC.
• For more information, see the Castle Link software page.
• For more information about the Castle Link software, visit the Castle Link Downloads page.
• Castle Link contains a proprietary interface adapter and standard USB cable with micro-B port. All you need is an available USB port on your PC.

System Requirements: Castle Link is compatible with Windows Vista, Windows 7, Windows 8 and Windows 10. Note: Macintosh users may take advantage of software such as Parallels Desktop, VMware Fusion, or Apple's Boot Camp along with Windows Vista, Windows 7, Windows 8 and Windows 10. to run the Castle Link software, provided the Macintosh has an Intel processor. Macintosh installation is not supported by Castle Creations.

CC BEC 15A - maximum voltage 58V - 14S

The CC BEC 2.0 complements our established line of BECs that hobbyists have relied on for years. With hundreds of thousands in use, users can rely on this new design to safely power today's high-performance digital servos and accessories. The CC BEC 2.0 has rugged dual output cables that deliver clean power to sensitive electronics. Castle Link2 can be used to adjust the output from 4.75 to 12 volts to power today's power-hungry servos, cameras and other accessories. The output voltage is factory set to 5.25 V. Do it right the first time, invest in the CC BEC 2.0 to protect expensive electronics for the long term.

Note: The CC BEC 2.0 should never be used in series or parallel with another BEC or backup receiver connected to the RX/servo side of the circuit.

Scope of supply: 1 x CC BEC 2.0 15A

Castle Link V4 is our new 32-bit based USB adapter.

Program your  ESC on your Windows® PC (10 or higher) with the Castle Link V4 USB programming kit.

• Set up of programmable options with point and click ease
• View your current program settings
• Download and view the ESC's onboard data logs
• Update ESCs with new firmware (if available)

Set-up instructions:

1. Download the Castle Link 2 software
   
2. Run the Castle Link 2 installer and follow on-screen prompts.
3. Plug the Castle Link V4 adapter into the provided Type-C USB cable.
4. Connect the ESC's receiver lead to the Castle Link adapters prongs; the brown wire connects to the pin marked "GND" or "-".
   Note: Castle Link Classic program is not compatible with the Castle Link V4 adapter and Cobra 8 ESC.

Package includes:

• Castle Link V4 adapter
• Type C USB cable
• Castle Decal sheet

Castle Link contains a proprietary interface adapter and standard USB cable with Type-C port. All you need is an available Type-A USB port on your Windows 10 PC.

System Requirements: Castle Link 2 is compatible with Windows 10 or higher.