Velcro & Glue materials

Manual Dual cartridge Dispensing Glue Gun for Glues of 50 mL

DMA51-00-10 is a black/gray manual dispenser. It is designed for use with 50 ml cartridges and will work with 1:2 mix ratio products.

 

MEGABOND 2000 is the first choice among high-performance adhesives and meets the highest demands where standard adhesives fail. This high-performance adhesive is excellently suited for demanding applications where conventional adhesives do not provide the required strength.

Versatile Applications

With MEGABOND 2000, materials such as metal, wood, ceramics, and hard plastics can be permanently bonded. Ideal for the quick and reliable bonding of a wide variety of materials. After complete curing, the adhesive surface can be further processed and painted.

Product Highlights

• Exceptional impact, peel, and shear strength
• Resistance to weathering
• Rapid curing
• Minimal surface preparation needed
• Temperature resistance: Permanent up to +120°C, short-term up to +140°C

Application Examples

Bodywork and Exterior: Bumpers, spoilers, radiators, external mirrors, body panels, windshields, door windows, FRP parts, door panels, rear and front lighting, reinforcement and installation of floor panels, roof elements, grill parts, front and rear end caps, advertising and stops, plastic wheel caps, bumper angles, and much more.

Simple Processing

• Preparation: The surfaces to be bonded should be clean, oil- and grease-free. A roughened surface increases strength.
• Application: Mix the material until a uniform color is achieved. Apply  MEGABOND 2000 and join the parts together.
• Curing: Handling strength is achieved after about 60 minutes, complete curing after 12 hours.
• Storage: Close the cartridge after use. Do not process below +5°C.

Technical specifications:

Base Methyl methacrylate
Viscosity 150,000-200,000 mPa-s at +20 °C
Density 0.97 g/ml
Shrinkage 5%
Temperature resistance -55 °C to +120 °C
Gap-filling ability 1-10mm
Shore hardness 75D
Hand strength 60 minutes
Final strength 12 o'clock

The black Liquid Tape is a rubber coating that insulates and seals your cables, electrical circuits, servo motors, ESCs, etc. It is applied with a brush directly on the circuits to be protected, and remains very easy to remove once dry, thus leaving you access to the components.
Do-It-Yourself rubber coatings, Performix by Plasti Dip liquid electrical tape coatings allow you to rubberize, insulate, and seal all of your electrical connections. It is a dielectric coating which seals out moisture and other contaminates permanently. Liquid Tape is the most effective product on the market with a dielectric protection of 48,000 V/mm, it does not harden, puncture or become brittle, even in extreme weather conditions.
An applicator brush is included.

Features:

Flexible--won't crack, chip, or become brittle
Insulates from electrical shock, vibration, and heat
Grip provides safe, non-slip comfort and control
Durable--resists weather, chemicals, impact, and abrasion

POWERZIP strip, 16mm wide, 1meter long

Power tape, holding power is up to 50 kg!!, Double face transparent silicone tape ( red cover), excellent for installation of wires, wood, fiber, Gyro , Receiver and more..

Its suitable for internal & external use it offers high adhesion to a wide variety of surfaces. It has superior 'wetting out' properties which increase the bonded surface area increasing the strength of the bond. It has excellent ageing properties and is resistant to U.V. light, abrasion, corrosion & moisture.
Service temperature is -30°c - +80°c (continuous)/ +130°c (shorterm).

Pack of  1 Meter long 16mm wide

 

POWERZIP strip, 16mm wide, 1meter long

Power tape, holding power is up to 50 kg!!, Double face transparent silicone tape ( red cover), excellent for installation of wires, wood, fiber, Gyro , Receiver and more..

Its suitable for internal & external use it offers high adhesion to a wide variety of surfaces. It has superior 'wetting out' properties which increase the bonded surface area increasing the strength of the bond. It has excellent ageing properties and is resistant to U.V. light, abrasion, corrosion & moisture.
Service temperature is -30°c - +80°c (continuous)/ +130°c (shorterm).

Pack of  1 Meter long 25mm wide

 

ZAP Zip Kicker (CA Glue Accelerators)
FORCES IMMEDIATE CURE OF CYANOACRYLATE GLUE
BEST ACCELERATOR FOR ZAP AND ALL OTHER SUPER GLUES
EXPANDS GAP FILLING CAPACITY
SOLVES MOST TOUGH TO BOND MATERIAL COMBINATIONS

ZIP KICKER Is the best way to accelerate the cure time of all brands of super glues. When sprayed directly on a glued joint it forces the immediate cure of the CA glue. Thick or slow style glues form an instant hard outer shell when sprayed with ZIP KICKER, the catalytic action begins curing the remaining liquid CA at an accelerated rate from the outside in, creating a strong bond.This action allows the creation of small to very large fillets and the ability to fill large gaps or cracks.Wood turners love this ability and often are able to progressively fill in large cracks and save the piece they are working on. ZIP KICKER will not harm most materials making perfect to use not only on wood but various plastics, metals, paints, and fabrics.

Helpful Hints:

A little goes a long way!Because ZIP KICKER cures CA glue by a chemical reaction, you can precisely control how fast the glue sets up.Use a small amount to start the reaction at one spot and it will continue until the glue is set.The more ZIP KICKER you apply to the glue, the faster it will cure. Once the entire surface of the glue has been sprayed with kicker and the reaction has started, adding more kicker will not speed up the cure rate.In hard to reach areas or when trying to join parts that are not porous you can pre-treat one of the parts to be joined with ZIP KICKER, apply ZAP GLUE to the other and join the two together.When working with balsa wood spraying ZIP KICKER on the back side of thin sheeting can set the CA underneath.Even a part treated with ZIP KICKER and allowed to dry will speed the cure time of any CA that comes in contact with it.DO NOT SPRAY ZIP KICKER AROUND YOUR BOTTLES OF CA,A SMALL AMOUNT OF KICKER ON THE OPENING OF YOUR CA BOTTLE CAN AND WILL SET OFF AND HARDEN THE ENTIRE BOTTLE.Although ZIP KICKER will work on most materials and paints, always test on samples for compatibility.For critical applications test sample joints for the designed strength requirements.

 Bottle of 8 Oz/ 237ml

COLD METAL STICK (STEEL OR ALU). Two-pack epoxy putty for filling cracks, holes and leaks in fuel containers. Suitable for metal, wood, ceramics, concrete and glass. Can even be used on damp surfaces and under water. Full cure time three hours. Can be sanded and painted once hard.

Specifications:

• Working in tempratures of -30°C -- + 150°C. Curing time is 60min.
• Final resistance is + 50 kg/cm² (after 24 h.)
• Contents: 56 g

Description:

Includes:

• 2x Velcro Tape 36x100mm

Use for:

• Goblin Fireball

Includes:

50pcs Zip Tie 2.5 x 200mm

Scorpion lock strap has the revolutionary change from the traditional battery strap, with the newest design of non-slip grip to assure maximum traction. Between the non slip surface, and metal fastener, this 19" long lock strap (XXL) can securely hold large UAV batteries (Approximately 12s 8000mah - 12000mah).

4pcs included in this set.

The new Scorpion Lock Straps feature a revolutionary non-slip coating on the inside surface that securely locks your battery in place and prevents them from shifting, even during the most radical 3D aerobatic maneuvers. These large size straps are perfect for 500 to 700 class electric helicopters or larger RC Aircraft. The large size strap measures 1 inch wide by 12.5 inches long (25mm x 315mm), so they will fit around a 6-cell 5000mah battery pack. The straps feature a tough plastic buckle and a strong Velcro closure for maximum holding power and security.

Each package contains 3 Scorpion Lock Straps.

Tetras 280 Velcro loop 2 pieces

Special quick-setting adhesive for assembling rigid polystyrene foam (eg Styropor®), and in conjunction with other materials.
The elastic adhesive film is colourless and waterproof.Materials:
Rigid foam materials such as Styropor®, and in conjunction with other materials such as wood, paper, metal, ceramic, plaster, textiles and various plastics.
Also highly suitable for sticking photosInstructions for useApply adhesive to both parts to be stuck together. Leave to dry. Once dry to the touch (after approx. 10 minutes), press together very firmly for a short time. Take care not to damage rigid foam material.

Velcro lock Fastener strap Green

Strap velcro , for any application, 1 meter long

Those straps will help to secure your receiver, gyro, battery pack to your heli tray with easy maintenance access.

• Re- usable, and last forever, it is a "Must to have" item.
• Fits up to 6s 5000 Lipo packs, also multiple straps can be connected.
• Set including 3 straps, 400 x 20 mm

Z-Poxy 5 minute Formula is a two component epoxy with a short curing time. This epoxy is particularly suitable for making/modeling Streamer heads that have eyes fitted.

5 MINUTE Z-POXY is a premium high strength two part epoxy adhesive. Vibration resistant and fuel proof, this epoxy is perfect for all types of hobbies and crafts. Use it on all fire wall and engine mount installations, its perfect for attaching bulkheads and formers in epoxy glass fuselages and boat hulls. It does not get brittle with age and its easy to mix, just combine equal parts by volume. Handy to have at home for all types of fix-it jobs, great to have in the shop for all types of wood working and furniture repair.

Helpful Hints:

5 MINUTE Z-POXY does fully cure in approximately 5 minutes, that means you will have about 2 minutes working time. To clean up any uncured or unmixed epoxy, use alcohol, isopropyl or methanol, either will work. Thinning of 5 MINUTE Z-POXY is possible in smaller ratios, thinning too much will alter the cured properties and may not produce an adequate bond. It is best to test the thinned epoxy, let it cure and adjust as need. Mix Z-POXY in a plastic cup or on a non porous surface like a piece flexible plastic. Only mix enough epoxy as needed, any excess epoxy cannot be saved after it has been mixed. Pot life and cure time will vary when the epoxy is thinned. Since epoxies cure by an exothermic chemical reaction, ( give off heat ) and heat can speed the cure of epoxy, mixing large amounts can shorten the pot life if not spread out right away.

PT-38
8oz. (227.2ml) Z-POXY 5 Minute

The world's best canopy glue. 560 dries clear making it the perfect glue to use for attaching airplane canopies and vacuum formed ABS parts. The excellent shock resistant flexible bond means your airplane parts will stay put even when subject to high vibration and extreme speeds. 560 is also an excellent craft glue. The nontoxic and water based formula means kids can safely use it for their special projects. Worlds best canopy glue

• Clear and fast drying
• Dries flexible and clear
• Non-Toxic
• Water clean-up

Works best on:

• Canopy
• Canvas
• Clay
• Cloth
• Fabric
• Foam
• Most Plastics
• Plater
• Vinyl
• Wood

Bottle size:

• 2 oz / 59 ml

•   Odorless "no more tears" formula
•   Safe for all hobby foams
•   Medium thick, cures in 15 seconds
•   20-gram bottle

Zap-O Foam Safe CA is a true odorless CA. It has the same gap filling properties as Zap-A-Gap CA+ but without the fumes. It works great on balsa, plywood, bass wood and most other modeling and hobby materials. Zap-O Foam Safe CA is also great for craft work when gluing foam shapes or various materials to foam products. Medium thick formula that cures in 15 seconds.
Packaged in a 20-gram bottle. To cure properly, Zap-O Foam Safe CA must be used with Zap Foam Safe Kicker.

Works best on:

• Carbon Fiber
• Cell Foam
• Ceramics
• EPS Foam
• Foam Board
• Polystyrene
• Wood

Zap CA Thin is a super thin super glue. Zap Thin bonds almost all materials, such as Balsa and other soft woods, but also Aluminum, Porcelain, Fabric, Fiberglass, Metal, most plastics, ceramics and rubber. Glued between 1 and 5 seconds. The package contains 29.5 ml. Zap CA Thin.

ZAP-A-GAP CA+ Is the best selling instant glue in the world. The ability to bond virtually anything to anything with consistency unequalled by any other brand makes it the favorite adhesive across many varied disciplines. Widely used throughout the hobby industry, it is the absolute best and most consistent performing glue for model building and crafting. Some uses besides hobbies and crafts include; jewelry manufacturing and repair, taxidermy, pool cue tips, darts, archery, knife making, mold and pattern making, furniture refinishing and antique repair, auto detailing, dental molds and patterns, ceramic repair, and for fishing, fly line splicing and fly tying. For manufacturing, the ability to bond metal and / or plastic parts allows for fast simple fixturing and positioning for assembly or machining. Wood turners and manufactures of custom wood products appreciate the ability of ZAP-A-GAP CA+ to help save their projects by filling in and bonding cracks that often occur in expensive hard woods. Wood, plastic, metal, glass, ceramic, fabric, rubber, fiberglass, carbon fiber, or any combination of, ZAP-A-GAP CA+ can help solve many tough bonding problems.

Helpful Hints:

A little goes a long way! More glue doesn’t always mean a stronger joint. Only apply enough glue to evenly coat the area to be bonded when the parts are joined. Many times glue needs to be applied only to one part. Working or positioning time will vary depending on the material. Even though ZAP-A-GAP CA+ is a gap filling formula, some of it will wick into porous materials. For porous products you may have to apply more glue to get the strongest bond, it would be best to try bonding some test pieces to determine the proper amount. For modeling applications where a small fillet is desirable, bond the parts and let the glue set, then go back and create the fillet, use kicker to immediately set the glue. For critical applications test sample joints for the designed strength requirements.

Safe on most foam products Compatible with most other Foam Safe CAs Works on Balsa, Spruce, Plywood, Plastic and Metals, etc Forces most CAs to cure in 10 seconds or less Increases Gap filling and fillet forming compatibility None-fuming formula INCLUDES: One bottle of Pacer Foam Safe Kicker One pump REQUIRES: Use with CA glues SPECS: 2oz (59.1ml)

ZAP AFTER RUN

• CORROSION INHIBITOR
• PENETRATES EXISTING CORROSION
• PROTECTS ENGINE BEARINGS DURING STORAGE
• ONE TREATMENT LASTS FOR MONTHS

Treats engines and inhibits corrosion from forming. Adding After Run 2 to the engine protects all of the internal parts. One treatment lasts for months. Ideal for coating metal push rods before inserting them into sleeves

Works best on:

Gas or Glow Engines

Metal

SLO Zap is a thick slow drying adhesive. Slo Zap glues almost all materials, such as Balsa and other soft woods, but also Aluminum, Porcelain, Fabric, Fiberglass, Metal, most plastics, ceramics and rubber.

This adhesive gives 30 seconds of positioning time and 60 seconds of drying time. The package contains 1 OZ - 28.3 gr - 29.5 ml. SLO Zap.

Thick and strong for high-stress areas. Works well on hard woods such as Maple and Oak. In modeling its ideal for laminating wood parts and forming fillets. Because its thick, it will not run, it forms a very clean even fillet around all types of joints. The high cured strength means it works great on higher stress areas. Allows 30 seconds for positioning and cures in 60 seconds or less. To accelerate cure time use Zip Kicker.
2-oz /56gr bottle

ZAP ZIP Kicker ensures that superglues  (Cyanoacrylate, CA-glues) cure even faster. Sometimes it can be useful to let the adhesive cure a little faster if, for example, it has a very small bonding surface or if it is difficult to access.

It is a volatile material that gives off a distinct odor, do not breathe it.

The ZIP kicker works on almost all materials such as Balsa, Metal, Plastic, etc. and will not leave any residue. Safe for most plastic products. Content 59.7 grams.

ZAP-A-GAP CA+ Is the best selling instant glue in the world. The ability to bond virtually anything to anything with consistency unequalled by any other brand makes it the favorite adhesive across many varied disciplines. Widely used throughout the hobby industry, it is the absolute best and most consistent performing glue for model building and crafting. Some uses besides hobbies and crafts include; jewelry manufacturing and repair, taxidermy, pool cue tips, darts, archery, knife making, mold and pattern making, furniture refinishing and antique repair, auto detailing, dental molds and patterns, ceramic repair, and for fishing, fly line splicing and fly tying. For manufacturing, the ability to bond metal and / or plastic parts allows for fast simple fixturing and positioning for assembly or machining. Wood turners and manufactures of custom wood products appreciate the ability of ZAP-A-GAP CA+ to help save their projects by filling in and bonding cracks that often occur in expensive hard woods. Wood, plastic, metal, glass, ceramic, fabric, rubber, fiberglass, carbon fiber, or any combination of, ZAP-A-GAP CA+ can help solve many tough bonding problems.

Helpful Hints:

A little goes a long way! More glue doesn’t always mean a stronger joint. Only apply enough glue to evenly coat the area to be bonded when the parts are joined. Many times glue needs to be applied only to one part. Working or positioning time will vary depending on the material. Even though ZAP-A-GAP CA+ is a gap filling formula, some of it will wick into porous materials. For porous products you may have to apply more glue to get the strongest bond, it would be best to try bonding some test pieces to determine the proper amount. For modeling applications where a small fillet is desirable, bond the parts and let the glue set, then go back and create the fillet, use kicker to immediately set the glue. For critical applications test sample joints for the designed strength requirements.

This is the new Lock Strap feature a Patented anti slip material in the inside surface that securely locks your battery in place and prevents them from slipping, during extreme maneuvers. This strap is made for large applications, e.g lipos of 16000-22000 mah and over. also possible to attach 2 lipos in this size with one strap.

This strap tested with heavy battery in shaking and throwing bench, its safe to use on all UAVs

Those straps are made from heavy duty nylon, with special antislip material, stitched with Kevlar wire for strongest application possible and heavy loads of up to 8g forces.
use on large UAV, Multicopters and more.

Strap measures  620 mm long and 50mm wide, so they will also catch lipos from 6-12000mah without any problem.

Each package contains 2 Velcro straps

Straps coming with Plastic or Metal buckle.

The new XL Lock Straps feature a Patented anti slip material in the inside surface that securely locks your battery in place and prevents them from slipping, during extreme maneuvers.
These large size straps are made from heavy duty nylon Velcro material and perfect for 500 to 800 class electric helicopters or larger RC Aircraft.

Strap measures 25 X 450 mm, so they will also catch lipos from 6-8S 5000-8000mah without any problem.
Each package contains 3 Velcro straps

4- Fuel Resistant Anti Vibration Pads w/3M™ Adhesive Heli Team Tip: To protect the adhesive from fuel add a band of CA around the outside of the anti vibration pad. WORKS GREAT !

SPARTAN Replacement gyro pads for gyros .
The pack includes (5x) "3M" 30x30x2mm, (1X) Metal plate

The new Antislip Battery Lock Straps feature a Patented anti slip material in the inside surface that securely locks your battery in place and prevents them from slipping, during extreme maneuvers, racings, crashes.

These straps are made from heavy duty nylon Velcro material and perfect for FPV racers and applications where you need to secure 3-4 s Lipo.

• Strap measures 20x 200mm
• Package contains 3 Velcro straps
   

Mikado Velcro straps 20x280mm (4 pcs)