TX & RX Accessories

TX Switch Knobs Cap BLUE Short V3 (2pcs, Fit All Brand TX)

Contents:

• Switch Knobs Cap x 2pcs
• O-ring x 2pcs
• Hex Nut x 2pcs

TX Switch Knobs Cap ORANGE Long V3 (2pcs, Fit All Brand TX)

Contents:

• Switch Knobs Cap x 2pcs
• O-ring x 2pcs
• Hex Nut x 2pcs

TX Switch Knobs Cap ORANGE Short V3 (2pcs, Fit All Brand TX)

Contents:

• Switch Knobs Cap x 2pcs
• O-ring x 2pcs
• Hex Nut x 2pcs

TX Switch Knobs Cap RED Long V3 (2pcs, Fit All Brand TX)

Contents:

Switch Knobs Cap x 2pcs

O-ring x 2pcs

Hex Nut x 2pcs

TX Switch Knobs Cap RED Short V3 (2pcs, Fit All Brand TX)

Contents:

• Switch Knobs Cap x 2pcs
• O-ring x 2pcs
• Hex Nut x 2pcs

Enlarged stick head provide more friction to your finger tips and thus have a precise control movement.

The length of the stick can be adjusted and fixed with a set screw.

Avaliable for Jr (M4)
Colors-Black

Vbar Control 3-Position TX switch Long version

Vbar Control 3-Position TX switch Short version

VBar Control fast charger

VBar Control lanyard

VBar Control lanyard RED

VBar Control RX-Satellite Connection Wire, 120mm

VBar Control RX-Satellite Connection Wire, 200mm

VBar Control TX Rotary knobs colored

VBar Control/Scorpion ESC-Cable 350mm

VBar Control/Scorpion ESC-Cable 500mm

Case for VBar NEO including 180 mm 2.4 GHz antenna wires

For the 2nd hardware generation
04945/46 VBar NEO 6.1 Express (with antenna connectors on the main board)

VBar NEOs of the 1st hardware generation can not be converted.
For those devices, please use VBar Control RX Satellite 04882 and connecting cable 04977.

You can identify devices of the 2nd generation in 'My Devices' at www.vstab.info/devices, by the addition of (no VLink) or (VLink).
Devices of the 1st generation do not yet have that addition yet.
The change took place around serial no. 20007500, from here on please check for the addition and the internals (s. above).
To enable the receiver function, please purchase the Crossgrade from our App Store, which you can access through the VBar Control Manager, with the device connected and powered up (boot plug must be present).
If the Crossgrade is not available for your device, you have a device which can not be converted.
Also, you can buy the Crossgrade for (no VLink) devices only, so you can not accidentally purchase it for a device which already is VLink.

RX Antenna support flat mounting black

RX Antenna support for tailboom diameter from 20-30mm

This New Backup Guard II is much stronger than its predecessor, with many new features as well!

One new extraordinary feature is the Charge Mode. This means that the Backup Guard II can charge up the Backup Battery, with balancing, while it is operating. Charging rate will be 0.5A. This means you will no longer need to charge the Backup Battery ever again!

The Backup Guard II is now only the “Power Board” and you can connect your own size of 2s Lipo with JST-XHR Connector.

The Backup Guard II provides DC 5V with 10Amp Output, which is enough to land the aircraft if the ESC/BEC has some failure.

The Second-generation of Backup Guard II has 4 LED that will indicate the status.

Charging mode.

BEC lower than 5.5V.

Specifications

• Weight : 10grams (without battery)
• Dimension: 44mm x 25.2mm x 10.5mm
• Li-Po inpit: 2S/7.4V (500~1000mah)
• Output: DC 5V/ 10 Amp Continues Current.
• Charging Plug: JST-XHR

The Backup Guard II is now only the “Power Board” and you can connect your own size of 2s Lipo with JST-XHR Connector.