TX & RX Accessories

Jeti Trim nut black for JETI transmitter DC-24

Matching with the switches on the top of the JETI transmitter tray DC-24

• H: 4,8mm
• D: 9,7mm

Contents:
Pack of 2

Jeti Trim nut black for JETI transmitter DS-24

Matching with the switches on the top of the JETI transmitter DS-24

• H: 4,8mm
• D: 9,7mm

Contents:
Pack of 2

Jeti Trim nut black for JETI transmitter tray DC-14/16 FRONT panel

Matching with the switches on the top of the JETI transmitter tray DC-16

• H: 5,45mm
• D: 10,75mm

Pack of 2

Jeti trim nut silver for JETI Hand transmitter DS-16

Matching with the switches on the top of the JETI transmitter DC-16

• H: 6,2mm
• D: 9,7mm

Contents:
Pack of 2

Jeti trim nut silver for JETI transmitter DC-16

Jeti trim nut silver for JETI Hand transmitter DS-16

Matching with the switches on the top of the JETI transmitter DC-16

• H: 6,2mm
• D: 9,7mm

Contents:
Pack of 2

Jeti Tx Switch nut spanner

Jeti Universal Magnet Switch

MULi 6S EX is  a sensor for checking voltage of Li-XX batteries that checks the voltage by service connector of every single cell. It allows you to check the voltage up to 6 Li-XX cells.
You can check voltage of every single cell, store its history (maximum, minimum), total voltage of the whole battery, and the sensor can also give notice of exceeding selected parameters. Data from the sensor are transferred via DUPLEX system.

• Weight     6g
• Dimensions [mm]    36 x 20 x 5
• Operational temperature [°C]    -10 ... 85
• Supply Voltage [V]    3,5 ... 8,4
• Average Current [mA]    9
• Range of measured voltage [V]    0 ... 4,4

JR Original Sticker logo JR White

JR Transmitter Adjustable Length Lanyard Neck Strap, also will fit all radios

Original JR single-point neckstrap,

Width approx 30 mm.

JR and SPEKTRUM Transmitter SWITCH NUTS

Full set including 8 pcs and Removal/installation tool. WILL NOT WORK ON THE 12X or 8103.

You'll notice that the upper rim of the nut is smooth. Some Transmitters have the slots cut in the nuts had sharp corners. If you using to put the fingers between the switches, this got to be very irritating. Those nuts have smooth rim.
The colors are just a bonus

Give your radio a bling look.
CNC sticks for JR or Hitec transmitters

Set of 2.

Alow you to adjust, while flying , the mixture ratio, and to reach the best engine performance .
Moreover, you can adjust the mixture ratio and avoid overheat

RC lost Airplane/helicopter/drone  finder Alarm.

• Connect the alarm between the servo and the receiver, i.e. act as a servo extension cord.
• Turn on your TX. and you will hear 2 x beep sound.
• Do not move any of the control stick on the TX or simply turn off the the TX. You will hear a continuous beep sound after 1 minute. It will stop once u turn on your TX or move the control stick.
• If you ignore the continuous beep sound for around 2minutes, the beep sound will change the a louder V sound.
• You need to disconnect the alarm from the receiver in order to switch of the alarm.

Specifications:

• RC Radio Control  Lost Finder Tracker
• Suitable Controller: All PPM/FM, PCM/FM, AM Tx/Rx
• Loud >85dB alarm gets your attention
• Two alarm tones pattern
• Works with AM/FM PPM or FM/PCM R/C systems
• Plugs into any standard servo channel
• Operating Voltage(v) : 4-6v
• Current Drain(mA) : 1-35
• Can be heard in 50 meter distance

How to set up

1. 1. Connect the lost alarm between the servo (the one which runs when flying) and the receiver, i.e. act as a servo extension cord
2. 2. Turn on your transmitter
3. 3. Turn on your receiver then you will hear two beep sound
4. 4. To test if it is functioning:
5. Do not move any of the control stick on the transmitter for 1 min. or simply turn it off
6. You will hear a continuous beep sound after 1 minute
7. If you ignore the continuous beep sound for around 2 minutes, the beep sound will change to a louder V sound
8. It will stop once you move the control stick or power off the receiver
9. 5. If you cannot find you plane, do not move the control stick or turn off your transmitter for 1 min for the alarm sound
10. 6. By the tracking sound, you will be able to locate your RC plane / Helicopter
11. 7. To stop the alarm : Move the control stick or Power off the receiver
12. Can be connected to any kinds of servo
13. Should be connected to the servo that runs when flying

M3 Futaba - Spektrum DX6i, DX7s, DX8,DX9 Transmitter Long Stick Ends BLACK

Give your radio a bling look.
CNC sticks for Futaba transmitters

Set of 2.

M3 Futaba - Spektrum DX6i, DX7s, DX8,DX9 Transmitter Long Stick Ends BLUE

Give your radio a bling look.
CNC sticks for Futaba transmitters

Set of 2.

M4 JR Transmitter Long Stick Ends BLACK

Give your radio a bling look.
CNC sticks for Futaba transmitters

Set of 2.

M4 JR Transmitter Thumb Stick Ends BLACK

Enlarged stick head provide more friction to your finger tips and thus have a precise control movement.

M4 JR Transmitter Thumb Stick Ends BLUE

Enlarged stick head provide more friction to your finger tips and thus have a precise control movement.

Micro JST Female To Regular Servo Male Converter

Use to plug the SPEKTRUM H2060 NANOLITE Servo to Regular Flybarless Unit.

Stainless steel socket wrench for the finishing caps of all switches

T6 socket wrench for all T6 Torx bolts in VBar Control

Spare plungers for fine-adjustment of the power button

Neck strap with soft pad for VControl tray

Mikado Protection Case for NEO Aluminum case, black color #05270

For devices of the 2nd Generation (V2) only.

Mikado Protection Case for NEO Aluminum case, Silver color #05549

For devices of the 2nd Generation (V2) only.

Case for VBar NEO  For the 2nd hardware generation
04945/46 VBar NEO 6.1 Express (with antenna connectors on the main board)
04949/50 VBar NEO 6.1 Express NEO VLink (with antenna wires plugged in directly to the single pc board)
05054 VBar NEO VBasic

Description:

Mikado Rubber Grip Set Black, VControl

Mikado Temperature Sensor (- 300°C) VBar Control #05058

Mikado VBar Control Battery ID Sensor

Benefits at a glance:

• Automatic detection of flight pack batteries in a model.
• Battery logbook stored in the radio automatically.
• Simplified battery management.

Required accessories:
VBar Control radio 04841 or set 04842, 04843 with VBar Control RX-Satellite and VBar with Spektrum-Satellite-Connectors (Telemetry-Bus).
Current/Voltage/Capacity Sensor 04890.
Battery ID Tags 04908 (10-pcs. each; 5 pcs. included with each sensor).

Consumer benefits:
Less risk of damaging batteries by deep discharge when using flight packs with different capacities or of different age.
Automatically creates and stores logbooks in VBar Control for all flight packs that have already been entered,
which can be analyzed on a computer later on.
Automatic selection of known batteries in VBar Control, independently from the selected model: plug & fly.

Designed to refresh your Mikado Vbar (not touch) in nice cool outlook! Carbon Red or Carbon Orange

Usage: For Mikado vbar (Not Touch).TX not included, Carbon Red or Carbon Orange- choose yours.

Feature:

Well protected your transmitter,prevent it from being scratched

Colorful and shiny sticker,make you transmitter more beautiful

Make your TX look different

Mikado Vbar Metal rotating knobs, black (2 pc.), VBar Control

Mikado Vbar Softtouch rubber to cover for VControl switches

Multi harness cable 15cm for receiver and flybarless system or multicopters Flight controllers

Package includes:

• 1 multi harness cable lead 15cm.

Add a little style, Grip and protection to your TX switches ! These non-slip silicone covers are molded to fit the standard switch types used on a wide variety of RC transmitters. Great for your Jeti, Mikado, FrSky, FlySky, Futaba, JR and Others (TX switch must be Flat)

Set Includes

5x LONG switch Non-Slip Silicone Transmitter Switch Cover

5x SHORT switch Non-Slip Silicone Transmitter Switch Cover

Colors:

• Black
• Blue
• Red
• Yellow
• White
• GREEN
  
• Multicolor

The PowerBox Sensor V3 is the third generation of the PowerBox Sensor, which is well-known throughout the world. For almost twenty years the PowerBox Sensor has represented the standard for small to medium-sized models thanks to its compact format and versatility.

By using the latest components we have been able to reduce the size of the Sensor V3 significantly. For example, the case is now exactly half as deep (11 mm compared with 22 mm). Nevertheless, the Sensor V3 still fits neatly in the aperture used by its predecessor.

The introduction of a top-quality aluminium case, machined and anodised, has brought a substantial increase in the unit’s cooling efficiency, with the result that the maximum continuous current capacity of the PowerBox Sensor V3 is around 35 % higher. In fact, the peak load capacity is twice as high: the Sensor V3 can handle more than 20 A for several second

Features

• High-performance battery backer
• Ultra-light unit, compact format
• Double regulated output voltage
• Redundant switch and regulator circuitry
• User-selectable output voltage: 6.0 V or 7.8 V
• Separate RGB LED voltage indicators for each battery
• Telemetry support for CORE systems
• Supports 4 different battery types: 2s LiPo, 2s LiIon, 2s LiFePo and 5s NiMH
• Regulator monitoring
• Suppression of servo feedback currents

PU adhesive gel is a material that possess excellent vibration dampening characteristics, ideal for mounting gyroscopes, receivers, or other electronics in vibration prone areas. The gel can be re-used by cleaning off containment (such as dust) with water. Mild detergent can also be used to wash away oily residues. Once dried the gel will regain its adhesiveness. The PU adhesive gel is an ideal replacement for traditional gyro foam tape. Its excellent vibration dampening characteristic can minimize impact induced damages on electronics.

Specifications:

●Material:PU
●Size:110x55x3mm

Accessories:

●PU adhesive gel x 1
●Hook & loop fastening tape x 2

Radio Transmitter Right Angle Locking Toggle Switch

• Super quality right angle panel mount locking toggle switch.
• This switch can mount in a 0.25" hole in panel.
• Contacts are SPDT rated 5 Amp at 120VAC.
• Brand new! Comes with one panel mounting nut.