Speed controller & BEC

This Battery Eliminator Circuit (BEC) is perfect for providing clean 5 or 6v power to your receiver, flight control board, LEDs or other low voltage equipment. Simply connect your 2-6s lipo to the input.

Specifications:

• Output: 5v/3A
• Input: 5.5v-28v (2-6S Lipo pack)
• Size: 41.6x16.6x7.0mm
• Weight: 7.5g Features

One of the most Powerful and reliable Bec systems up to 15A,high voltage! up to 45V input

• Reg Type : Switching
• Input Voltage Range : 11V ~ 45V (3~10 Cells)
• Output voltage Range : 5.2V, 6.0V, 6.8V, 7.4V, 8.4V Selectable
• Voltage ADJ : 4.8V~7.7V ADJ (Potentiometer)
• Output currant(Peak) : 15A
• Output currant(Cont) : 7A
• Size : 12mm(H) x 31mm(W) x 52mm(L)
• Weight : 14g (Excluding Cables)

If you're running unregulated LiPo or LiFe power to your servos, this regulator will allow you to run regulated current to your sensitive Gyro and Tail servo. Integrated heat sink allows for superior cooling.

Specification:

• Input voltage : 6 to 10V (5 to 8 cell NiCd/MH or 2-cell LiFe/Po)
• Output voltage : 5.2V or 6.0V
• Output current : 3A, MAX 10A(@6V,30sec)
• Input 2CH,
• Output 2CH
• Size : 10mm(H) x 23mm(W) x 40mm(L)
• Weight: 9 grams
• Components : Main unit 1EA, RX cable 2EA, Operating guide

Duo(GVR-3003) Regulator is primarily designed for use with gyros in helicopters.

The UBEC is an external switching mode DC-DC regulator; it draws the DC voltage from 2-6S Lipo battery, drops it to a voltage level that is suitable for receivers and other electronic devices, and keep providing the stable current output up to 10Amp. As the UBEC has such a powerful output capability, so it is particularly applicable for large helicopters and fixed-wing aircrafts.

Specifications:

• Input Voltage: 6V－25.2V (2-6S LiPo)
• The output voltage is programmable by dip switches.
  4 Options: 5.0V/6.0V/7.4V/8.4V
• Output Amperage: Continuous Current: 10A, Peak Current: 20A
• Dimension: 43.1 x 32.3 x 12.5mm (L x W x H)
• Weight: 36g  (1.27oz) 

The UBEC uses a high-performance DC-DC switching module that draws its voltage from 2-6S LiPos. The module regulates the voltage down to a previously defined value that is required by the receiver or other electronic devices. This is extremely stable and the output current is permanently up to 10A or briefly at 15A.

Because this UBEC is not only powerful, but also waterproof and dust-proof, it is particularly suitable for the use in Cars, but can be used in other models.

Features:

Highly efficient DC-DC regulator chip for a transmission efficiency of over 90%.

An all-metal housing design helps conduct heat and reduces electromagnetic interference.

Adjustable UBEC output voltage (6.0V / 7.4V / 8.4V) applicable for servos with different voltages.

The continuous current of UBEC is up to 10A and max. 15A and can thus be used for various electrical devices (e.g. car lights, winches, windshield wipers, etc.).

Excellent waterproof and dust-proof design with IP67 rating.

Multiple protection functions: over current protection, output short circuit protection, overheating protection, safe and reliable.

External switch enables the UBEC to be switched on / off easily.

LED display to show the status of the UBEC.

1. Input Voltage: 2-6S LiPo
2. Output Voltage: 6.0V / 7.4V / 8.4V (adjustable)
3. Current cont./peak: 10A / 15A
4. Dimensions: 45x20x16.2mm
5. Weight: 34g

UBEC 3A with selctable output voltage

The 3A-UBEC is a switch mode DC/DC regulator, it outputs a consistent safe voltage for the receiver, gyro and servos.
It is very suitable for RC helicopter and other RC models especially when the built-in BEC in the speed controller has a very limited output capability.

Specification:

• Output Voltage: 5V@3A or 6V@3A (Selectable by using a jumper connector)
• Continuous output current: 3 Amps
• Input: 5.5V-26V (2-6S Lipo or 5-18 cells NiMH /NiCd)
• Size: 43mm*17mm*7mm (L*W*H)
• Weight: 11g

Features:

• Uses an advanced switch mode DC-DC regulator IC.
• The output is powerful enough even working with 4S to 6S Lipo battery.
• Battery polarity reversal protection.
• A metal shield and a filter significantly reduce the electromagnetic interference.
• The working status is shown by an LED, it lights when the UBEC works normally.

12V Power Supply UBEC Gimbal Flight Control AV Transmitter For FPV Multicopter Quadcopter

• Specially design for multicopter
• Metal block case with great heat dissipation, LED indicators
• Metal shielding shell, good heat dissipation, the user can use double sided tape to stick it anywhere in the plane, you can also use screws.
• This product ripple, high efficiency, and provide a steady output currents up to 3A for image transmission, brushless head, flight control, photographic equipment, power use.

Technical parameters:

• Input Voltage:  7-26V
• Output voltage:  5.2 / 12V
• Current:  3A
• Weight:  9g
• Size:  27* 17* 5mm

Warning:

• Battery polarity cannot be reversed.
• Voltage cannot exceed the operating voltage range of products; this will cause damage to the product.