Scorpion Motors

This is a new motor for 30cc – 35cc gas equivalent models running on 19” – 21” propeller. Typically for Acrobatic Airplanes in the 70” – 74” size range.
We made 3 kv options, for 12s , 8s, and 6s operation to allow good range and selection for different type of modelers who want to use either HIGH POWER 12s system, unique 8s, or more economic single 6s operation.

Motor KV options : we carefully selected to be optimized for their relevant battery cell count selection. The -215kv option on 12s, has got the most performance pulling up to 90A / 4000W of power with 13.4kg+ of thrust. However, to match equal power on a 6s lipo setup, would pull upwards of 180+Amps, resulting in hot electronics, puffed batteries, and short flights. So the -415 KV of the 6s version is relatively lower, resulting in slight lower power. Maxing out at about 155A / 3441w with 12kg of thrust, which keep temperatures in line, and lipos happier, all will still providing great performance. The 8s system is in between the 12s / 6s option in terms of power and current draw.

All motors are still great power systems for 70” – 74” acrobatic airplanes providing unlimited vertical performance, and cool, efficient running power systems.

SPECS:

Motor Kv 215 RPM / Volt- OTHER KV optional
Weight (Motor only) 523.4g (18.46 oz)
Weight (including Prop mount accessories) 548.40g (19.344 oz)
Motor Body Dimensions 59.3 mm x 52.6mm (+ 18mm prop spacer) (2.33" x 2.07 (+0.70 prop spacer))
External Shaft Diameter 8mm
Continuous Current 70A
Continuous Power 3552 Watts
Peak Current* 90A
Peak Power* 4000 Watts
Max Rated Lipo Cell** 12s
Stator Diameter 50.0 mm (1.97 in)
Stator Thickness 25 mm (.984 in)
No. of Stator Arms 12
Magnet Poles 14
Motor Wind 9T/10T Delta
Motor Wire 12-Strand x 0.33mm
No-Load Current (IO/20V) 0.99 Amps
Motor Internal Resistance 17.5mΩ

*Our ratings are classified as TRUTHFUL. Continuous Current / Power correlates to actual sustainable power levels. Peak Power is for intermittent full throttle usage ranging from 5 - 60 seconds depending on use case and cooling*
**Higher Cell Count possible with smaller prop usage**

Included in the Box
1 x A-5025 Motor
1 x Cross Mount
3 x 6mm Female Connectors
3 x Heat Shrink
1 x Hardware Accessory Bag

Optional KV 215/310/415

Product Description

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. Unlike most motors on the market, who choose one motor / magnet design, and then only change the windings to achieve different KV's (which usually provides one KV range with good results, and average results for the other KV ranges). On the A - series motors we looked at each kv / power range individually. We choose the most optimal magnetic design for each individual kv and implemented it, so that each KV version has the best possible Performance and Efficiency .

The performance and efficiency results are unlike anything we have seen before!

The A-3017 series was designed specifically for 48" Acrobatic Airplanes, or other Sport / UAV airplanes requiring up to 962w of power. Also known as the 30-32E size. For the A-3017 we offer 3 x kv ranges of 560 / 600 / 920 for various applications and various voltage ranges. The 560kv being specifically for smoother sport flying applications, or UAV applications.

Specifications

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. Unlike most motors on the market, who choose one motor / magnet design, and then only change the windings to achieve different KV's (which usually provides one KV range with good results, and average results for the other KV ranges). On the A - series motors we looked at each kv / power range individually. We choose the most optimal magnetic design for each individual kv and implemented it, so that each KV version has the best possible Performance and Efficiency .

The performance and efficiency results are unlike anything we have seen before!

The A-3017 series was designed specifically for 48" Acrobatic Airplanes, or other Sport / UAV airplanes requiring up to 962w of power. Also known as the 30-32E size. For the A-3017 we offer 3 x kv ranges of 560 / 600 / 920 for various applications and various voltage ranges. The 600kv being the premier high power choice for 6s powered 48" Acrobatic Planes or suitable UAVs.

Specifications

Product description

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. Unlike most motors on the market, who choose one motor / magnet design, and then only change the windings to achieve different KV's (which usually provides one KV range with good results, and average results for the other KV ranges). On the A - series motors we looked at each kv / power range individually. We choose the most optimal magnetic design for each individual kv and implemented it, so that each KV version has the best possible Performance and Efficiency .

The performance and efficiency results are unlike anything we have seen before!

The A-3017 series was designed specifically for 48" Acrobatic Airplanes, or other Sport / UAV airplanes requiring up to 962w of power. Also known as the 30-32E size. For the A-3017 we offer 3 x kv ranges of 560 / 600 / 920 for various applications and various voltage ranges. The 920kv being the premier high power choice for 4s powered 48" Acrobatic Planes or suitable UAVs.

Specifications

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

Specifications

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and 2 x single strand enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

Specifications

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and 2 x single strand 1.18mm enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

Recommended Prop Selection :

24x10E / 24x13E (Carbon) / 25x12E / 26x8E

Recommended ESC -: Tribunus II+ 14-200A ESC SBEC

Acrobatic Weight Range -: 8.18kg - 12.7kg (18.0lbs - 28.0lbs)

Sport / UAV (single engine) Weight Range : - 12.7kg - 36kg (28.0lbs -80lbs)

Specifications

Motor Kv 160 RPM / Volt
Weight (Motor only) 998g (35.20 oz)
Weight (including mount + Prop mount accessories) 1115g (39.33 oz)
Motor Body Dimensions 78.5 mm x 67.8mm (3.09" x 2.67")
External Shaft Diameter 10mm
Continuous Current 80A
Continuous Power 4218 Watts
Peak Current* 124A
Peak Power* 6450 Watts
Max Rated Lipo Cell** 12s - 14s
Stator Diameter 65.0 mm (2.56 in)
Stator Thickness 28 mm (1.10 in)
No. of Stator Arms 12
Magnet Poles 14
Motor Wind 8T Delta
Motor Wire 2-Strand x 1.12mm
No-Load Current (IO/20V) 1.9 Amps
Motor Internal Resistance 11.4 mΩ


*Our ratings are classified as TRUTHFUL. Continuous Current / Power correlates to actual sustainable power levels. Peak Power is for intermittent full throttle usage ranging from 5 - 60 seconds depending on use case and cooling*
**Higher Cell Count possible with smaller prop usage**

Included in the Box
1 x Scorpion A-6528 BLDC Motor
1 x A-55/65 Cross Mount (stock)
4 x M4 Cross Mount Mounting Bolts
3 x Female 6mm Connectors
3 x Heat Shrink
3 x Scorpion Stickers
2 x M10 Nuts

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and 2 x single strand 1.18mm enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-6528-180kv was designed for 90"- 95" Acrobatic Airplanes, or other Sport / UAV airplanes requiring up to 7200w of power. Compared to the -200kv version, this motor is designed to swing a larger / slower spinning prop in the 24" - 26" range on 12s battery.

Recommended Prop Selection :

24x10E / 24x13E (Carbon) / 25x12E / 26x8E

Recommended ESC -: Tribunus II+ 14-200A ESC SBEC

Acrobatic Weight Range -: 8.18kg - 12.7kg (18.0lbs - 28.0lbs)

Sport / UAV (single engine) Weight Range : - 12.7kg - 36kg (28.0lbs -80lbs)

Specifications

Motor Kv 180 RPM / Volt
Weight (Motor only) 998g (35.20 oz)
Weight (including mount + Prop mount accessories) 1115g (39.33 oz)
Motor Body Dimensions 78.5 mm x 67.8mm (3.09" x 2.67")
External Shaft Diameter 10mm
Continuous Current 95A
Continuous Power 4218 Watts
Peak Current* 162A
Peak Power* 7200 Watts
Max Rated Lipo Cell** 12s
Stator Diameter 65.0 mm (2.56 in)
Stator Thickness 28 mm (1.10 in)
No. of Stator Arms 12
Magnet Poles 14
Motor Wind 7T Delta
Motor Wire 2-Strand x 1.18mm
No-Load Current (IO/20V) 2.39 Amps
Motor Internal Resistance 6.85 mΩ


*Our ratings are classified as TRUTHFUL. Continuous Current / Power correlates to actual sustainable power levels. Peak Power is for intermittent full throttle usage ranging from 5 - 60 seconds depending on use case and cooling*
**Higher Cell Count possible with smaller prop usage**

Included in the Box
1 x Scorpion A-6528 BLDC Motor
1 x A-55/65 Cross Mount (stock)
4 x M4 Cross Mount Mounting Bolts
3 x Female 6mm Connectors
3 x Heat Shrink
3 x Scorpion Stickers
2 x M10 Nuts

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and 2 x single strand 1.2mm enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-6528-200kv was designed specifically for 85"-95" Acrobatic Airplanes, or other Sport / UAV airplanes requiring up to 6000w of power. This motor is equivalent to a 60cc/76cc gas engine. We call it 60/76cc because with a 23" prop it is very equivalent to a 60cc gas engine and pulls less amps and therefore could run smaller batteries for lighter overall model weight. Or with a 24" prop it pulls as hard as a 76cc gas engine, with more amps thus requiring a larger battery.

Specifications

Product Description

Scorpion is proud to announce our latest high performance M series motor for large scale UAV. It can carry up to 5.3kg total weight with an Octocopter (8 motors multi-copter) using 4S Lipo battery (Max support 6S).

M-3011-760KV has also been specifically constructed to perform less vibrations overall, while also giving a strong performance to carry loads of professional equipment for aerial photography.

Specifications

Product Description

Scorpion is proud to announce our latest high performance M series motor—the Scorpion M-3014-380kv. It is for large scale UAV and it can carry up to 7.8kg, with an Octocopter (8 motors multi-copter) which uses 6S Lipo.

The Scorpion M-3014-380kv has been specifically designed to give less vibrations, and to overall give an extremely high performance while effectively carrying loads of professional aerial photography equipment.

Specifications

Product Description

Scorpion is proud to announce our latest high performance M series motor for large scale UAV. New technology of using 1.12mm SINGLE STRAND winding to deliver 1110 Watts maximum continuous power on 10s Power. Each motor deliver 3,675g maximum thrust with using 18x6 propellers in 6S, capable to hovering an 8-rotors UAV in a total weight of 14.7kgs.

Scorpion M-4215-320kv has been specifically constructed to perform less vibration overall, and to give an extreme performance to carry load of professional equipment for aero photography.

It suitable for two types of propeller which has space 12mm screw hole and 6mm & 8mm inner diameter.

Specifications

The new Scorpion MII-3011 Cinematography Edition is a purpose built motor, designed specifically for 8"-9" prop cinelifters. This motor checks every box you would need it to for your cinematic build.

High Power / High Torque / Unmatched Efficiency / Ultra Smooth / Low Noise

Designed specifically for props such as HQ 8x4x3 and similar on 6s power, this motor has a power density like we have never seen before, and unmatched thrust measuring up to 3200g of thrust till the end of the battery. While most cinelifter builds fly as a X8 coaxial configuration, with MTOW of 4kg, our test results show amazing performance with even an X4 configuration flying at 3.5kg. Accounting for coaxial loss, as a X8 configuration, this motor could fly up to 4.5-5kg MTOW with ease.

Specifications

The new Scorpion MII-3011 Cinematography Edition is a purpose built motor, designed specifically for 8"-9" prop cinelifters. This motor checks every box you would need it to for your cinematic build.

High Power / High Torque / Unmatched Efficiency / Ultra Smooth / Low Noise

Designed specifically for props such as HQ 9x4x3 and similar on 6s power, this motor has a power density like we have never seen before, and unmatched thrust. With max thrust of 2711g, the 875kv edition is lower power then its 1100kv counterpart, but is designed for smooth flying and long duration, especially on Coaxial builds IN THE 4.0-4.5kg range.

Specifications

Product Description

The MII-40 Series motor! This motor specially made for multi-copter. This motor provides all the power that you can use, while still maintaining excellent efficiency and higher power than any competition, perfectly balanced rotor. And the bearing has change to 4*11*4 since M-4010 version.

It suitable for two types of propeller which has space 12mm screw hole and 6mm & 8mm inner diameter.

Specifications

Product Description

The MII-40 Series motor! This motor specially made for multi-copter. This motor provides all the power that you can use, while still maintaining excellent efficiency and higher power than any competition, perfectly balanced rotor. And the bearing has change to 4*11*4 since M-4010 version.

It suitable for two types of propeller which has space 12mm screw hole and 6mm & 8mm inner diameter.

Specifications

Product Description

The MIII-40 Series motor! This motor specially made for multi-copter. This motor provides all the power that you can use, while still maintaining excellent efficiency and higher power than any competition, perfectly balanced rotor.

It suitable for two types of propeller which has space 12mm screw hole and 6mm & 8mm inner diameter.

Specifications

In combination with our new A-Series motor line debut, we are also please to announce our new "PLUG-N-POWER" combo kits! This pairs our high power and high efficiency A-series motors with one of our suitably sized, pre-programmed, and pre soldered Tribunus ESCs! Providing you with a tested, proven, and convenient power system combo which is sure to provide you immense power, at the best efficiency!

With 3D flight, low end torque and acceleration are crucial. Many companies opted to go with a “large diameter / thin height / high pole count motors" to try and get increased torque / acceleration. However doing this has the side effect of very large physical size and Lower Peak Efficiency. We at Scorpion have opted to stay with our proven 12N14P stator design. We have fine-tuned the magnets in the rotor to have amazing Peak Efficiency, and amazing Top End Power. Then, when used in combination with our Tribunus ESC, which has our proprietary drive algorithm which has unique switching pattern, along with features such as dynamic timing and dynamic frequency, we are still able to attain amazing low-end torque and acceleration. With the combination of the 2, we get “the best of both worlds” in the sense we have amazing peak Efficiency and Power with our stator design, and amazing low-end torque from the ESC side. Additionally, physically speaking our motors are similar length, with a much smaller outer diameter then other designs, which can be easier to fit inside cowls or fuselages of your airplane or UAV.

This specific A-3017 PNP Combo (6s), is designed for 6s powered 48" Acrobatic Airplanes, and UAV's requiring up to 962w of power with 3.5kg+ of thrust. It comes with our A-3017-600kv motor, pre programmed and pre-soldered Tribunus 06-80A ESC and a custom Scorpion Gold Metallic painted 13x6 propeller. This PNP combo is sure to give you the power you need, with the efficiency you want, all while making your airplane standout from the crowd

Acrobatic Weight Range (600kv) - : 1.3kg - 2.18kg (46oz - 77oz)

Sport / UAV (single engine) Weight Range (600kv) - : 2.3kg - 5.03kg (81.1oz - 177.6oz)

Recommended Battery Size - : 6s (22.2v) 1400-2000mah Lipo

Specifications

MOTOR :

Motor Kv 600 RPM / Volt

Weight (including mount + accessories) 154g (5.43 oz)

Motor Body Dimensions 36.60 mm x 36.5mm (1.44" x 1.44")

External Shaft Diameter 5.98mm

Continuous Current 25A

Continuous Power 555 Watts

Peak Current 43A

Peak Power 962 Watts

Max Rated Lipo Cell** 6s

No. of Stator Arms 12

Magnet Poles 14

ESC :

Max Continuous Current 80 Amps

Peak Current 100Amps

Operating Voltage Range 11-26.1 Volts

BEC Output voltage: 5.1V to 7.1V adjustable.

Max Continuous BEC Output 8 Amps @ 7.1 V

Max BEC Output 12A pules

Size 47.1 x 31 x 20 mm (1.85 x 1.22 x 0.79 in)

Weight (Without Connectors) 56g (1.98 oz)

Drive frequency 8kHz - 32kHz

Included in the Box

1 x Scorpion A-3017-600kv

1 x Tribunus 06-80A ESC SBEC (pre soldered w/ XT60)

1 x Scorpion 13x6 Metallic Gold Painted Prop

1 x Scorpion M Lock Strap

3 x Scorpion Stickers

16 x 3x10x1mm thrust spacing washers

4 x M3x10 moutning screws

4 x M3x16 mounting screws

In combination with our new A-Series motor line debut, we are also please to announce our new "PLUG-N-POWER" combo kits! We wanted to take the guess work out of Electric Power Systems, and provide our customers with a simple, convenient and reliable power system for their 90E /20cc-25cc sized airplanes. The A-4225 PNP Combo is the solution. This pairs our high power and high efficiency A-series motors with one of our suitably sized, pre-programmed, Tribunus ESCs! Providing you with a tested, proven, and convenient power system combo, which is sure to provide you immense power, at the best efficiency! This PNP combo is ready to easily bolt on, and give you the power you need, with the efficiency you want.

MOTOR SPECIFICATIONS :

Motor Kv 500 RPM / Volt

Weight (including cross mount + Prop mount accessories) 398g ( 14.04oz)

Motor Body Dimensions 50.7mm x 50.9mm (+12.0mm prop spacer) (1.99" x 2.00" (+ 0.47") )

External Shaft Diameter 8mm

Continuous Current 100A

Continuous Power 2220 Watts

Peak Current* 140A

Peak Power* 3108 Watts

Max Rated Lipo Cell 6s

Stator Arms 12

Magnet Poles 14

ESC SPECIFICATIONS :

Max Continuous Current 120 Amps

Peak Current 160Amps

Operating Voltage Range 11-26.1 Volts

BEC Output voltage***: OFF/5.1/6.1/7.1/8.1

Max Continuous BEC Output 10 Amps @ 8.1 V

Peak BEC Output 30 Amps/1s @ 8.1 V

Size 76.7 x 36.5 x 25.4 mm (3.02 x 1.44 x 1 in)

Weight (Without Connectors) 120g (4.23 oz)

Drive frequency 8kHz - 32kHz

Cable gauge 12 AWG

Included in the Box

1 x Scorpion A-4225 BLDC Motor

1 x A-42 Cross Mount (stock)

4 x M4 Cross Mount Mounting Bolts

12 x 4x16x1 Thrust Shims

1 x M8 Nut + prop washer

1 x Tribunus II 06-120A ESC SBEC

2 x BEC Cables

1 x Backup Guard II (power board)

1 x Scorpion Lock Strap (L)

3 x Scorpion Stickers

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

Specifications

Motor Kv 540 RPM / Volt

Weight (Motor only) 288g ( 10.16oz)

Weight (including mount + Prop mount accessories) 336g (11.85 oz)

Motor Body Dimensions 45.8mm x 50.7mm (+12.0mm prop spacer) (1.80" x 2.00" (+ 0.47") )

External Shaft Diameter 8mm

Continuous Current 90A

Continuous Power 2000 Watts

Peak Current* 115A

Peak Power* 2553 Watts

Max Rated Lipo Cell** 6s

Stator Diameter 42.0 mm (1.65in)

Stator Thickness 25 mm (0.98in)

No. of Stator Arms 12

Magnet Poles 14

Motor Wind 5T Delta

Motor Wire 23-Strand x 0.29mm

No-Load Current (IO/15V) 1.54 Amps

Motor Internal Resistance (phase-phase) 18.2 mΩ

Motor Inductance (phase-phase) @ 1khz 10µH

Product Name: Scorpion Anti-Slip Pit Mat

1. Protect your work surface

2. Keep the sharp tools secure in place

3. Eco-friendly PVC foam material

4. Waterproof

5. Great cushioning and support

6. Not only for RC, also suitable for household

7. All purpose

8. Size: L750mm × W820mm

9. Thickness: 2mm

Specifications

Eco-friendly PVC foam material

Size: L750mm × W820mm

Thickness: 2mm

Color: Black

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 250C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7430 was designed specifically for airplanes requiring a 70cc-85cc equivalent gas engine, or other airframes requiring up to 7500w of power.

Recommended Prop Selection :

For 12s - 28x12 C2E / 28x13 C2E // 100cc performance

For 14s - 25x12E / 26x12E // 85cc performance

Recommended ESC : Tribunus II+ 14-200A ESC SBEC

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 155 RPM / Volt
Weight (Motor only) 1271.0g (44.8 oz)
Weight (including prop mount accessories) 1367g (48.21 oz)
Motor Body Dimensions 86.80mm x 70.4mm (+20.0mm Prop Spacer) (3.42" x 2.77" (+0.79" prop spacer))
External Shaft Diameter 10mm
Continuous Current 110A
Continuous Power 5328 Watts
Peak Current* 150A
Peak Power* 7500 Watts
Max Rated Lipo Cell** 12s - 14s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 30 mm (1.18 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 7T 4Y
Motor Wire 1.12mm dia
No-Load Current (IO/20V) 2.54A

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 250C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7430 was designed specifically for airplanes requiring a 70cc-85cc equivalent gas engine, or other airframes requiring up to 7500w of power.

Recommended Prop Selection :

For 12s - 25x12E / 26x12E // 85cc peformance

Recommended ESC : Tribunus II+ 14-200A ESC SBEC

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 185 RPM / Volt
Weight (Motor only) 1255.0g ( 44.2 oz)
Weight (including prop mount accessories) 1351g (47.65 oz)
Motor Body Dimensions 86.80mm x 70.4mm (+20.0mm Prop Spacer) (3.42" x 2.77" (+0.79" prop spacer))
External Shaft Diameter 10mm
Continuous Current 120A
Continuous Power 5328 Watts
Peak Current* 169A
Peak Power* 7500 Watts
Max Rated Lipo Cell** 12s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 30 mm (1.18 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 6T 4Y
Motor Wire 1.2mm dia
No-Load Current (IO/20V) 2.54A

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7441 was designed specifically for airplanes requiring a 100cc - 126cc equivalent gas engine, or other airframes requiring up to 9,300w of power.

Recommended Prop Selection :

12s Lipo - 28x13E, 29x12E, 30x12E

14s Lipo - 27x12E, 28x10E

Recommended ESC : Tribunus II+ 14-200A ESC SBEC + Scorpion 40mm High Speed Cooling Fan V2

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 165 RPM / Volt
Weight (Motor only) 1605g (56.61 oz)
Weight (including prop mount accessories) 1717.0g (60.56 oz)
Motor Body Dimensions 86.80mm x 81.90mm (+20.0mm prop hub) (3.42" x 3.22" (+0.79 prop hub))
External Shaft Diameter 10mm
Continuous Current 120A
Continuous Power 6260 Watts
Peak Current* 178A
Peak Power* 9300 Watts
Max Rated Lipo Cell** 12s - 14s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 41.6 mm (1.64 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 5T 4Y
Motor Wire 1.35 mm
No-Load Current (IO/15V) 3.49 Amps

The Scorpion A - Series line of motors was designed to be the most optimal and premier choice of motor for your freestyle or UAV airplane. We have achieved incredible performance through incredible efficiency. By optimizing the magnets in the rotor, and using the best quality 0.2mm thickness silicon steel stator sheets, and single strand enamel coated copper wire windings rated above 200C+, the performance and efficiency results are unlike anything we have seen before! Combined with a robust design which has been tested extensively by our world class team pilots for longevity and reliability, we feel this motor checks and exceeds all measurable categories!

The A-7441 was designed specifically for airplanes requiring a 100cc - 126cc equivalent gas engine, or other airframes requiring up to 9,000w of power.

Recommended Prop Selection :

28x12 C2E = Optimal / 120cc performance

28x13 C2E = High Alt

Recommended ESC : Tribunus II+ 14-200A ESC SBEC + Scorpion 40mm High Speed Cooling Fan V2

NOTE: Due to the large size of airframes in this class, normally the battery wires must be extended. Running to long of battery cables WILL damage ESC and void your warranty. Precautions. If you model has long battery cables, precautions should be taken. We recommend the use of the Scorpion 1880uF Capacitor / PDB Board

Sport / UAV (single engine) Weight Range : - 16.14kg - 48.43kg (35.52lbs -106.56lbs)

Specifications

Motor Kv 180 RPM / Volt
Weight (Motor only) 1555g (54.85 oz)
Weight (including mount + Prop mount accessories) 1725g (60.84 oz)
Motor Body Dimensions 86.80mm x 81.90mm (3.42" x 3.22")
External Shaft Diameter 10mm
Continuous Current 141A
Continuous Power 6260 Watts
Peak Current* 202A
Peak Power* 9000 Watts
Max Rated Lipo Cell** 12s
Stator Diameter 74.0 mm (2.91 in)
Stator Thickness 45 mm (1.77 in)
No. of Stator Arms 24
Magnet Poles 28
Motor Wind 4T/5T Y
Motor Wire 1.35 mm
No-Load Current (IO/15V) 3.49 Amps

The HK5 Series lives up to and exceeds our standards of the most Powerful and Efficient motors, with market leading Torque per Amp capabilities. In addition, on the HK5 series we focused specifically on motor cooling and motor temperature. With an all new Internal Fan design, combined with our proven external centrifugal fan, we have nearly doubled the amount of airflow passing through the motor. The result is much improved cooling, and cooler operating temperatures.

The HK5-4030-1005kv is designed for lightweight 700 size helicopters on 6s -7s lipo, or other UAV application requiring up to 6900w of power

Specifications

Motor Kv 1005KV RPM/Volt
Weight 428.0 Grams ( 15.09oz)
Motor Body Dimensions 49.5mm x 62.0mm (1.95" x 2.44")
External Shaft Dimensions 5.98mm x 38mm (0.235" x 1.50")
Continuous Current 100 Amps
Continuous Power 3700 Watts
Peak Current 180A (2 seconds)
Peak Power 6900 Watts (2 seconds)
Max Lipo Cell* 6s-7s
Stator Diameter 40 mm (1.57 in)
Stator Thickness 30 mm (1.18 in)
No. of Stator Arms 12
No. of Stator Poles 10
Motor Wind 3T Delta
Motor Wire 1.6mm

*Higher Cell Count possible with appropriate gear ratio adjustment

Included

1 x HK5-4030 BLDC Motor
3 x Female 4mm Connectors
3 x Heat Shrink
1 x Hardware / Accessory Pack

The HK5 Series lives up to and exceeds our standards of the most Powerful and Efficient motors, with market leading Torque per Amp capabilities. In addition, on the HK5 series we focused specifically on motor cooling and motor temperature. With an all new Internal Fan design, combined with our proven external centrifugal fan, we have nearly doubled the amount of airflow passing through the motor. The result is much improved cooling, and cooler operating temperatures.

The HK5-4030-715kv is designed for 570-650mm size helicopters running on 8s-10s, lightweight 700 size helicopters on 8s, or other UAV application requiring up to 6900w of power.

Specifications

Motor Kv 715KV RPM/Volt
Weight 428.0 Grams ( 15.09oz)
Motor Body Dimensions 49.5mm x 62.0mm (1.95" x 2.44")
External Shaft Dimensions 5.98mm x 38mm (0.235" x 1.50")
Continuous Current 100 Amps
Continuous Power 3700 Watts
Peak Current 180A (2 seconds)
Peak Power 6900 Watts (2 seconds)
Max Lipo Cell* 10s
Stator Diameter 40 mm (1.57 in)
Stator Thickness 30 mm (1.18 in)
No. of Stator Arms 12
No. of Stator Poles 10
Motor Wind 4T Delta
Motor Wire 1.6mm

*Higher Cell Count possible with appropriate gear ratio adjustment

Included in the Box
1 x HK5-4030 BLDC Motor
3 x Female 4mm Connectors
3 x Heat Shrink
1 x Hardware / Accessory Pack

Scorpion special shaft for HK4025 motors, with extra Long extension, 31mm. Diameter of the shaft is 5mm

The Scorpion HK-4025, HKIII-4025 series motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4025, HKIII-4025 series Scorpion Helicopter Motors.

This shaft kit is for the HK-4025, HKIII-4025series motors that used in newer T-600 Heli. It measures 8mm in diameter, and is 84.9mm in length. The pinion end of this shaft is ground down to 5mm to allow the user to install 5mm pinion gears. The shaft kit will also fit other brushless motors that require a 5mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. The new SII series motors are an updated and improved version of the popular 30mm motors that have been so successful. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Plated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

All Scorpion SII-30mm motors come with Scorpion's new 2.5mm male Bullet style connectors already attached, and include a complete hardware package that contains the following: 3 matching female Bullet connectors for your speed controller, a cross style backplate mount with 4 screws, and a threaded shaft prop adapter.

Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. For the best overall combination of quality, performance, and value, give Scorpion Motors a try!

Specifications

• Stator Diameter 30.0 mm (1.18 in)
• Stator Thickness 14.0 mm (0.55 in)
• No. of Stator Arms 12
• Magnet Poles 14
• Motor Wind 16 Turn Delta
• Motor Wire 9-Strand 0.25mm
• Motor Kv 830 RPM / Volt
• No-Load Current (IO/10V) 1.06 Amps
• Motor Resistance (Rm) 0.042 Ohms
• Max Continuous Current 30 Amps
• Max Continuous Power 550 Watts
• Weight 129 Grams (4.55 oz)
• Outside Diameter 37.50 mm (1.47 in)
• Shaft Diameter 4.98 mm (0.196 in)
• Adapter Thread size M6*1.0
• Body Length 39.75 mm (1.56 in)
• Overall Shaft Length 68.5 mm (2.69 in)
• Max Lipo Cell 5s
• Motor Timing 5deg
• Drive Frequency 8kHz

Included in the Box

• 1 x Scorpion SII-3014-830KV Motor
• 1 x Scorpion 30mm Cross Mount
• 1 x Scorpion 5mm Threaded Prop Adapter
• 3 x Female Connectors
• 3 x Heat Shrink
• 4 x M3 Screws

Scorpion Competition HK-2221 replacement Shaft 3.17mm

The Scorpion HK-2221 motors are built with 4mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-22mm Scorpion Motors.

This shaft kit is for the HK-2221 series motors that used in newer T-450 Heli. The shaft measures 4mm in diameter, and is 58.7mm in long. The pinion end of this shaft is ground down to 3.17 mm. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing

Scorpion Competition HK-2221 replacement Shaft 3.5mm

The Scorpion HK-2221 motors are built with 4mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-22mm Scorpion Motors.

This shaft kit is for the HK-2221 series motors that used in newer T-450 Heli. The shaft measures 4mm in diameter, and is 58.7mm in long. The pinion end of this shaft is ground down to 3.5 mm. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing

With the trend of ultra light weight 700 size models running 6-8s batteries on the rise, the market called for a light weight, powerful, but not battery puffing motor. So Scorpion created the HKII-4225-810kv motor for a Limited Edition run! Sized directly between our proven HKIV-4025 and HKII-4525 motors in terms of weight and power, and LIGHTER yet MORE powerful then our competitors 4030 motors, this motor represents the most technologically advanced power source ever offered for an electric helicopter.

Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Plated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

Scorpion Motors are built to last, and are backed with a 1-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 1-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

• Stator Diameter:    42 mm (1.65 in)
• Stator Thickness:    25 mm (0.98 in)
• No. of Stator Arms:    12
• No. of Stator Poles:    10
• Motor Wire:    1-Strand 1.6 mm
• Motor Kv :   810KV RPM/Volt
• No-Load Current (Io/10V):    3.6 Amps
• Motor Resistance (RM):    0.009 Ohms
• Max Continuous Current:    115 Amps
• Max Continuous Power:    3404 Watts
• Weight :   393 Grams (13.77 oz)
• Outside Diameter:    52.3 mm (2.06 in)
• Shaft Diameter:    5.98 mm (0.24 in)
• Body Length:    51.50 mm (2.03 in)
• Overall Shaft Length:   85.5 mm
  
• Max Lipo Cell:   8s
• Max Peak Current:  170 Amps (5 seconds)
• Max Peak Power:    5032 Watts (5 seconds)
• Motor Timing:    5deg
• Drive Frequency:    8kHz

Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm lamination to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand temperatures of up to 200 degrees C (392 F).

All Scorpion HK Series 22mm motors come with 3.5mm male Bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller, heat-shrink to cover the bullet connectors and mounting screws. Since the HK series motors are primarily designed for Helicopter and Ducted Fan use, they do not include a prop adapter. If you intend on running a prop on this motor, you will need to purchase a prop adapter for a 3.17mm shaft (1/8 inch).

Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

Specifications:

• Stator Diameter:    22.0 mm (0.87 in)
• Stator Thickness:    21.0 mm (0.83 in)
• No. of Stator Arms:    9
• Magnet Poles:    6
• Motor Wind:    8 Turn Delta
• Motor Wire:    16-Strand 0.21mm
• Motor Kv :   3595 RPM / Volt
• No-Load Current (Io):    2.31 Amps @ 10 volts
• Motor Resistance (Rm):    0.024 Ohms
• Max Continuous Current :   45 Amps
• Max Continuous Power:    475 Watts
• Weight:    81 Grams (2.86 oz)
• Outside Diameter:    27.9 mm (1.098 in)
• Shaft Diameter:    3.17 mm (0.125 in)
• Body Length:    38.3 mm (1.508 in)
• Overall Shaft Length:    58.7 mm (2.311 in)
• Max Lipo Cell :   3s
• Motor Timing :   5deg
• Drive Frequency:    8kHz

Included in the Box:

• 1 x Scorpion HKII-2221-8 Motor
• 3 x Female Connectors
• 3 x Heat Shrink
• 4 x M3 Screws

Scorpion HK-22 C-Clip Kit factory replacement C-Clip

The Scorpion HK-22 C-Clip Kit are the factory replacement C-Clip, washers & set screw for all HK-22 Series Helicopter Motors. (Except HK-2206)

Included in the Box:

• 4 x C-Clips
• 4 x Set Screws
• 4 x Washers

The Scorpion HK-30 series motors have been developed for the newer electric helicopter that are now coming onto the market. This HK-3014-900 KV motor designed to provide long flight time and power that you need to use for Goblin 380, while still maintaining excellent efficiency and cool running characteristics.

Scorpion HK-30 Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to with stand high temperatures, making a motor that is virtually impossible to burn up in normal use.

This motors come with 4.0mm male bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller with matching heat shrink tubing. For maximum strength, motors feature an 5 mm diameter at the output shaft to fit standard size pinion gears.

Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

Specifications
Stator Diameter    30.0 mm(1.181 in)
Stator Thickness    14.0 mm(0.551 in)
No.of stator Arms    12
No.of stator Poles    10
Motor Wind    11T Turn Delta
Motor Wire    7-Strand 0.25 mm
Motor Kv    900KV RPM/Volt
No-Load Current    (IO/10V) 1.09 Amps
Motor Resistance(RM)    0.065 Ohms
Max Continuous Current    28 Amps
Max Continuous Power    650Watts
Weight    119 Grams (4.19 oz)
Outside Diameter    37.5 mm (1.476 in)
Shaft Diameter    4.98 mm (0.196 in)
Body Length    34.5 mm (1.358 in)
Overall Shaft Length    57.0 mm (2.244 in)
Max. Peak Current    43 Amp (2 Seconds)
Max. Peak Power    1000 Watts (2 Seconds)
Max Lipo    6S
Included in the Box
1 x Scorpion HK-3014-900KV 5mm shaft motor
3 x Female Connectors
3 x Heat Shrink
4 x M3*0.5 Screws

The Scorpion HK-30 series motors have been developed for the newer electric helicopter that are now coming onto the market. This HK-3020-1000 KV motor designed to provide all the crazy power that you even can't imagine for Goblin 380, while still maintaining excellent efficiency and cool running characteristics.

Scorpion HK-30 Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to with stand high temperatures, making a motor that is virtually impossible to burn up in normal use.

This motors come with 4.0mm male bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller with matching heat shrink tubing. For maximum strength, motors feature an 5 mm diameter at the output shaft to fit standard size pinion gears.

Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

Specifications

• Stator Diameter    30.0 mm(1.181 in)
• Stator Thickness    20.0 mm(0.787 in)
• No. of stator Arms    12
• No. of stator Poles    10
• Motor Wind    6+7 Turn Delta
• Motor Wire    12-Strand 0.25 mm
• Motor Kv    1000KV RPM/Volt
• No-Load Current    (IO/10V) 1.75 Amps
• Motor Resistance(RM)    0.030 Ohms
• Max Continuous Current    45 Amps
• Max Continuous Power    1050 Watts
• Weight    153 Grams (5.39 oz)
• Outside Diameter    37.5 mm (1.476 in)
• Shaft Diameter    4.98 mm (0.196 in)
• Body Length    40.5 mm (1.594 in)
• Overall Shaft Length    63.0 mm (2.480 in)
• Max. Peak Current    70 Amp (2 Seconds)
• Max. Peak Power    1600Watts (2 Seconds)
• Max. Lipo    6S

Included in the Box

• 1 x Scorpion HK-3020-1000KV 5mm shaft motor
• 3 x Female Connectors
• 3 x Heat Shrink
• 4 x M3*0.5 Screws