Robbe-Schluter

Left and right engine mounts

One piece of CNC Servo rocker.

Tail Boom Spacer , 1 piece

1 piece of metal skid brace

Flat Frame Spacer , SET OF 1

Central engine mount

Lower U-Shaped Engine mount

Front Bell Crank Spacer

M3 Threaded Round Spacer (1)

Unthreaded Round Spacer ( 1)

Half collective pitch arm

double ended closed loop collective pitch arm.

Collective pitch control shaft

Ground Plate

Set of 1 frame, or complete set including the ground plate DYX0021

Two Long canopy alloy mounting

DYX-0037 Aluminum Round Spacer 3mm ID, 5mm OD set of 4pcs

Color can be Aluminum clear or Black

Set of 4 pcs.

Collective pitch Push/pull rods . SET OF 2

This is the Set including: Mount plate and Pinion needed to use when converting Millennium / Dyna-X to Electric.

Motor Plate- Made from 7075 Aluminum, Anodized for Full oxide protection ( No real need, but we like our parts prefect ).
If you use Dyna-X, we will supply Spacers to fit the frames.

Pinion of choice Diameter 5 / 6 or 8mm / Module 1, Hardened Pinion, made from Stainless steel with special surface coating for perfect and quiet transmittion.

Included in Set ( Product Options)

• Motor Mount, made for 25mm screw distance motors
• Hardware (Screws/Shims)
• Spacers x 4( to fit Dyna-X) frames
• Pinion of Choice (M1)

This is the Set including: Mount plate, Pinion, and third bearing support,especially for very long shafts (48mm and longer). This is  all needed to use when converting Millennium/Dyna-X to Electric.

Motor Plate- Made from 7075 Aluminum, Anodized for Full oxide protection
If you use Dyna-X, we will supply Spacers to fit the frames.

Pinion of choice Diameter 5 or 8mm, Hardened Pinion, made from Stainless steel with special surface coating for perfect and quiet transmitting.

Included in Set (Product Options)

• Motor Mount- made for 25mm screw distance motors
• 3RD BEARING (S4605) for 5 MM shaft
• Hardware: 4 x HEX M3x8mm / 2 x HEX M3x50mm / 2 x M3 Locknut
• Spacers x 4 (to fit Dyna-X) frames
• Pinion of Choice

ELEVATOR ARM SET

ENGINE MOUNT SHIMS , 2pcs

A must for turbine smooth high speed running and accurate cyclic response. Crafted from solid in a single fully automated machining operation this headblock is supremely accurate, very strong and light.

This component has been designed to prevent movement of the tail drive pinion gear. Often the threads in the original plastic unit are overtightened and damaged resulting in the gear lifting out of correct mesh. Our alloy unit provides secure threads that can be fully tightened time after time. Supplied complete with shorter M2.5 socket screws for minimal weight, new bearings are pre-installed. The completed assembly is no heavier than the stock plastic part.

Want to make your Robbe heli extreme 3D?This kit will make your head extremely responsive,

FEATHERKEY 5X3X10

Flybar conus weight and stiffener.
Those conical  adapters must be fitted on any Helicopter to balance the flybar.
The conus creates good and equal Load Sharing on the Flybar Area and will prevent the flybar to weaken and break as a result of vibrations.This is a "Must" part for any Helicopter.
Fit 4mm flybars , made from  7075 Alu , set of 2 pieces.

Made from precision ground steel for excellent strength and corrosion resistance. Those flybars can help to improve hover stability for novice flyers and more 3D response for expert flyers.

Pack of 1 piece, 4mm diameter, 52cm long. Black color

FREE-WHEEL COVER

S4607 - FREE-WHEEL HUB MOUNTED

FREE-WHEEL- Special Sprague Bearing

FRONT CLUTCH, MOUNTED AL

FRONT STRUCTURE EXTENSION

Fuel Tank for Dyna-X, cover to be used originally from Robbe

HEXAGON SPACER