Robbe

Carbon Shroud Holder 2pcs, fits Robbe helicopters, Millenium, Nova, Cuatro

Robbe CLUTCH CAP #S4831

Robbe Clutch O-RING set (2pcs) #S0500

COLD METAL STICK (STEEL OR ALU). Two-pack epoxy putty for filling cracks, holes and leaks in fuel containers. Suitable for metal, wood, ceramics, concrete and glass. Can even be used on damp surfaces and under water. Full cure time three hours. Can be sanded and painted once hard.

Specifications:

• Working in tempratures of -30°C -- + 150°C. Curing time is 60min.
• Final resistance is + 50 kg/cm² (after 24 h.)
• Contents: 56 g

The Robbe FS 177 BB MG HV is a modern high-voltage surface-mounted servo in the 9 gram class with an 8mm slim housing. It is made of impact-resistant, tough plastic, which is extremely temperature stable. The motor and digital control electronics meet the highest quality standards.

The FS 177 BB MG HV is very well suited as a wing servo for ailerons and thanks to its robustness due to high-quality ball bearings also for flaps in thin wing profiles, e.g. on DLG (F3K), pylon models (F5D), but also in electric gliders of the class F5J.
The servo comes with extremely robust plastic servo arms.

The Robbe FS Servos are high-quality and precisely manufactured steering gears for the RC sector. Due to the high manufacturing standard and the resulting processing quality, you achieve maximum power, speed, reliability and positioning accuracy. The Robbe FS Servo series impresses with its exceptionally good price-performance ratio.

Specifications

• Working frequence: 1520μs / 330hz
• Operating Voltage:  DC6~7.4 V
• Operating Speed (6V): 0.09sec/60°
• Operating Speed (7.4V): 0.07sec/60°
• Stall Torque (6V): 2kg.cm
• Stall Torque (7.4V): 2.6kg.cm
• Dimensions: 23.5X8X24mm
• Weight:  9.4g  
• Connector Wire Length: JR/Futaba 150 mm
• Bearing: 2BB

ROBBE helicopters BEVEL GEAR 15Z M1 Milenium, Futura

Robbe helicopters NEEDLE ROLLER 2X9, Nova, Millenium 60 #S4269

ROBBE helicopters Starter extension with Hex shaft Round and flat end

This is a set of carbon pushrod for RC helicopters, thickness of carbon rod is 5mm.

set comes with CNC ends, ball links and 1m carbon tube, can be adapted to any needed size.

Special Bearing Oil

A must to use with Ball Bearings and any metal part in friction
Absolutely essential for model helicopters and cars, also for all other applications

Content: 8ml

ROBBE TEFLON GREASE 25G

All-purpose grease supplied in practical jet-applicator; ideal for the modeller. this product has same component as MICROLUBE GLXX

- friction and wear reduced five-fold
- extra safety margin
- suitable for plastic and metal
- useful life of parts extended up to 200%
- resistant to fuel and ageing
- temperature range -15°C to + 250°C

Applications:
- Plastic and metal differentials
- gears
- transmissions
- chains
- wheel bearings
- needle roller bearings

RO-Power Torque Brushless motors are lightweight, powerful external rotor motors with high torque and efficiency. They do not require a gearbox and are suitable for a wide range of applications. All components are manufactured on modern CNC machines from high-quality materials. Precise ball bearings increase the service life and minimize vibrations. We recommend the operation of RO-Power Torque motors with ROBBE Ro-Control speed controllers.

Technical data

Housing-Ø (mm): 22,8
Housing length (mm): 18
LiPo (S): 2-3
Shaft-Ø (mm): 5
Propeller: 3S/ 6x3, 5,5x4, 2S/ 7x4, 7x4
Weight (g): 20
Examples of use: F5K
RPM/V: 2250
Engine-type: External rotor
Weight category (g): 0 to 5

RO-Power Torque Brushless motors are lightweight, powerful external rotor motors with high torque and efficiency. They do not require a gearbox and are suitable for a wide range of applications. All components are manufactured on modern CNC machines from high-quality materials. Precise ball bearings increase the service life and minimize vibrations. We recommend the operation of RO-Power Torque motors with ROBBE Ro-Control speed controllers.

Technical data

Housing-Ø (mm): 22,8
Housing length (mm): 18
LiPo (S): 2
Shaft-Ø (mm): 5
Propeller: 2S/ 6x3, 6x4
Weight (g): 20.8
Examples of use: F5K
RPM/V: 2750
Engine-type: External rotor

Handy anemometer for mobile use.

Product features:
simple and efficient anemometer
removable rubber cover
Illuminated LCD display
integrated thermometer (measuring range -10 ° / + 45 ° C)
for button cell CR3032

Display area air speed:
m / s = 0..30
Ft / min = 0..5850
Node = 0..55
Km / hr = 0..90
Mph = ​​0..65

Technical specifications:
Dimensions = approx. 40 x 18 x 108mm
Weight = approx 52g
Power consumption = approx. 3mA

Wingo 2 for the joy of model flying Wingo is one of the best entry-level model aircraft, which came on the market in 1998 and has been sold successfully worldwide for many years. The model is now technically modified and available again. The Wingo 2 is made of lightweight EPO foam and is therefore even more stable and durable. All previous wooden parts have been replaced by injection-moulded plastic parts, which simplifies the assembly and reduces it to a few hours. The wing is screwed to the fuselage dome with a 5 mm plastic screw. The wing struts can be attached without tools and give the Wingo 2 additional stability. The brushless motor supplied is specially tuned to the Wingo 2 and gives the model good controllability even at low airspeed thanks to its pressure drive. Both the motor and the speed controller are already wired and equipped with reverse polarity protection. Plug connections soldered ready for installation. Motor and controller have power reserves to be able to use the Wingo 2 optionally also for the water start with float. Therefore 2 propellers of different sizes are already included with the model. The small 5 x 4" propeller is ideal for beginners as the Wingo 2 climbs away flat and does not have a large load change from idle to full throttle. This makes model flying easy to learn. If you have practice and enough flying experience, the enclosed larger 6.7 x 3.5" propeller can be mounted. With this propeller the drive power increases by approx. 15%. The climb behaviour is thus increased and the propulsion power is strong enough to start the Wingo 2 with float (optionally available) on the water. The power supply is a 3s 1100 mAh Lipo battery, which is also equipped with a reverse polarity protected plug connection and is available separately. The new self-adhesive decor has been designed so that the top and bottom sides are very different. This means that the pilot can easily see the flight attitude of the model. The detailed, illustrated construction stage description guarantees easy and safe Final assembly. =Specifications

• Wing-span  1100 mm
• Weight : +-530g
• Rec. engine :   RO-POWER 2822-23
• Manufacturer : ROBBE
• Fuselage EPO
• Wings : EPO
• Version : KIT
• Rec. Battery : 3S/1100mAh LiXX
• Antriebsart:  Elektro
• Flight Skill :    Beginners
• Building Skill :    Beginners

Contents

• largely finished model made of high-quality EPO moulded foam
• Aluminium tail unit carrier pluggable for better transport of the finished model
• high-quality decal sheet
• Plastic parts set for quick assembly
• Brushless controller Ro-Control 25A BEC ready wired
• Brushless motor Ro-Power 2822-23 ready wired
• Airscrew 5x4"
• Propeller 6,5x3,5"
• 2pcs. S0009 Rovor Servos
• Seat shell
• EPS transport device
• Small parts
• extensive, illustrated assembly instructions in German/English/French

ROD M2x138

Rotor Clip fixed Pin, Solo Pro /328

ROTOR SHAFT PIVOT BRACKET D28X45 M

ROTORHEAD HUB (for 10mm shaft)

RUBBER GROMMET, 2.8/7OX5/3.8X1

THRUST BEARING, Set of 1 bearing (8x19x7mm)

GUIDE 2PCS

HUB-lead to extend and distribute S-BUS-Servo connections. Extends the connection from 1 to 3 Servos.
Length 30 cm

C.SUNK AL.HE.SCR.M3X6 4PCS

SOCKET SCREW M2,5X8 2PCS

SEESAW

Self Healing Cutting Mat A1 600x900mm (Gray), DOUBLE SIDED 3mm with 5-lay construction
Perfect working underlay for cutting of foils, balsa, decal sheets and so on. Imprinted Length-,Wide- and Angle Screen.

Whether you are making models, crafting, drawing or for professional applications: our cutting mats offer you an excellent cutting surface that will make every project a success.
Thanks to the robust, self-healing surface and a material thickness of approx. 3mm, the mats remain almost intact even after many uses and ensure clean cuts without unsightly grooves. The non-slip properties guarantee stability, so that you can achieve an exact line with every movement - ideal for anyone who has the highest demands on precision and durability.

SELF HEALING - All Artway cutting mats are self-healing, helping prevent inaccurate cuts due to the grooves created by knives during previous cuts.

Centimeter and Inch Grid Markings - The A2 cutting mat comes in a neutral grey, with well-defined white grid markings and numbered measurements on both sides, one side in centimeters and the other in inches. Angular lines at angles of 45 and 60 degrees are also displayed on both sides.

The non-slip surface of the base holds the paper firmly and prevents the blade from running and cutting. Using a cutting mat extends the life of the blades and promotes accurate cutting.

Size A1 600x900mm  3mm thick

SELF-TAPE-SCREW 3X25 6PCS

SENSOR FINGER MILLENNIUM

Servo Accessory Bag Servo 4,3 Gr

SHIM WASHER 3X6X0,5 2PCS

SHIM WASHER 8X14X0,2 2PCS

SKID CONNECTOR for landing gear Robbe,SE, Millenium

4PCS in set

SKID JOINER

SLEEVE 2PCS

SLEEVE MOUNT