Receivers

RadioMaster R81 2.4GHz 8CH FULL range SBUS Nano Receiver Compatible FrSky D8 RSSI for RC Drone

• Channels: 8
• Frequency range: 2400-2483.5Mhz
• Power input range: 4.5-6V
• Signal format: Frsky D8 Compatible
• Output format: SBUS
• RSSI: RSSI on Ch9 of Sbus Output
• Control distance: more than 1km
• Antenna length: Approximately 6cm
• Size: 17x11mm
• Weight: 2grams

This R86 PWM Receiver has 6 channels and is Frsky D8 compatible, offering a range suitable for both drone and RC modelers.

Specifications

• Signal format: Frsky D8 Compatible
• Frequency range: 2400-2483.5Mhz
• Channels: 6 channels (PWM)
• Power input range: 4.5-8.4V
• Range: more than 1km
• Antenna length: 15 cm
• Size: 28x16.5x11mm
• Output format: PWM
• Weight: 4.8 grams

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series receivers are built-in a TCXO (temperature-compensated crystal oscillator) now, which ensures reliable, stable, and accurate signal reception, allowing for superior performance in demanding environments and enhancing the flight experience.

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today's pilots have come to expect.

The RP1 and RP2 2.4GHz ELRS nano series receivers are open-source receivers based on ExpressLRS. The Nano receivers, first developed by Jye Smith from the ExpressLRS development team, feature ESP8285 MCU and SX1280 RF chip. The RP1 has a UFL antenna socket for full-range antenna use. The RP2 has a built-in ceramic antenna which is super light and small in size and ideal for racing.

The RP1 and RP2 feature WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone.

Due to the low-latency and high-refresh-rate RF module, the RP1 and RP2 are ideal for FPV races or Long Range. Suitable for many models due to the ultra-light and Nano size, these receivers can fit just about anywhere!

Features

• Optimized PCB design for better heat dissipation.
• LNA for better receiver range.
• PA for better telemetry range.
• Antenna Diversity for improved signal stability and range.
• Built-in a TCXO (temperature compensated crystal oscillator)
  
  Specification

Item: RP2 Nano ExpressLRS 2.4ghz Receiver

• Type: ISM
• MCU: EPS8285
• RF Chip: SEMTECH SX1281
• Telemetry RF power: 10mW
• Antenna: On Board SMT Antenna
• Antenna: 65mm 2.4ghz T Antenna
• Frequency Range: 2.404 - 2.479 Ghz
• Maximum receive refresh rate: 500Hz/F1000Hz
• Minimum receiver refresh rate: 25Hz
• Working voltage: 5v
• Weight: 0.55g (On Board antenna)
• Dimension: 13mm*11mm*7mm
• Firmware Version: ExpressLRS v2.4 pre-installed
• FW Target: RadioMaster RP1/2 2400 RX
• Bus interface: CRSF
  
  Package Includes
  
  • 1 * RP2 ExpressLRS 2.4ghz Nano Receiver
  • 1 * User Manual
  • 1 * CRSF wire
    

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series receivers are built-in a TCXO (temperature-compensated crystal oscillator) now, which ensures reliable, stable, and accurate signal reception, allowing for superior performance in demanding environments and enhancing the flight experience.

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today's pilots have come to expect.

Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built-in FW updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.

The RP3 receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mW of telemetry performance and antenna switching for antenna diversity.

Features

• Optimized PCB design for better heat dissipation.
• LNA for better receiver range.
• PA for better telemetry range.
• Antenna Diversity for improved signal stability and range.
• Built-in a TCXO (temperature compensated crystal oscillator)
  
  Specification

• Item: RP3 Diversity Receiver
• Type: ISM
• MCU: ESP8285
• RF Chip: SX1281
• Telemetry RF power: Max 100mw
• Antenna: 65mm 2.4ghz T Antenna x 2
• Frequency Range: 2.404 - 2.479 Ghz
• Maximum receive refresh rate: 500Hz / F1000Hz
• Minimum receiver refresh rate: 25Hz
• Working voltage: 5v
• Weight: 4.6g (Including two antenna)
• Dimension: 22mm*13mm*4mm
• Firmware Version: ExpressLRS v3.0 pre-installed
• FW Target: RadioMaster RP3 Diversity 2400 RX
• Bus interface: CRSF

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

Advanced 6-channel 2.4GHz telemetry receiver for ACCESS and ACCST D16 RC protocols, with 6 high-precision PWM channels and 16 or 24-channel S.BUS modes. Two detachable antennas with IPEX4 connector provide full signal strength throughout the range. It's especially ideal for gliders, but you can use it for various other models as well. Thanks to its size and low weight, it is also suitable for small models. With redundancy support, it can be connected as a primary receiver via S.BUS. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices.

It features advanced anti-interference protection for reliable and stable signal transmission across the entire range. Smart-match system speeds up pairing. The black box function preserves basic flight data. LED indicates the receiver's operating status. A Smart matching function allows firmware updates wireless.

Features:

• Increased protection against RF interference and more stable RF transmission
• ACCESS and ACCST D16 RC protocols with smart pairing
• Basic black box function support
• 6 high-precision PWM channels
• S.BUS output port（with 16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• Full-range telemetry (S.Port or F.BUS)
• Wireless firmware updates (OTA)
• External battery/device voltage detection

Technical Specifications:

• Dimensions: 33×15×9.7 mm (L×W×H)
• Weight: 4.2 g
• Number of channels: 6 PWM channels + 16/24 channel mode via S.BUS
• Operating voltage range: 3.5–10 V
• Operating current: ＜65 mA at 5 V
• Operating range: ＞2 km (full range, may vary according to actual ambient conditions)
• External voltage measurement range via AIN2: 0-35 V (battery voltage divider ratio: 1:10)
• Antenna connector: IPEX4
• Compatibility: 2.4GHz ACCESS / ACCST D16 transmitters

Advanced 6-channel 2.4GHz telemetry receiver for ACCESS and ACCST D16 RC protocols, with 6 high-precision PWM channels and 16 or 24-channel S.BUS modes. Two detachable antennas with IPEX4 connector provide full signal strength throughout the range. It's especially ideal for gliders, but you can use it for various other models as well. Thanks to its size and low weight, it is also suitable for small models. With redundancy support, it can be connected as a primary receiver via S.BUS. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices.

It features advanced anti-interference protection for reliable and stable signal transmission across the entire range. Smart-match system speeds up pairing. The black box function preserves basic flight data. LED indicates the receiver's operating status. A Smart matching function allows firmware updates wireless.

It is equipped with a variometer that provides more accurate and faster measurement and transmission of altitude and vertical speed data. It also allows quick audio feedback from the variometer to the ACCESS transmitters.

Features:

• Increased protection against RF interference and more stable RF transmission
• ACCESS and ACCST D16 RC protocols with smart pairing
• Basic black box function support
• 6 high-precision PWM channels
• S.BUS output port（with 16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• Full-range telemetry (S.Port or F.BUS)
• Wireless firmware updates (OTA)
• External battery/device voltage detection

Technical Specifications:

• Dimensions: 33×15×9.7 mm (L×W×H)
• Weight: 4.2 g
• Number of channels: 6 PWM channels + 16/24 channel mode via S.BUS
• Operating voltage range: 3.5–10 V
• Operating current: ＜65 mA at 5 V
• Operating range: ＞2 km (full range, may vary according to actual ambient conditions)
• External voltage measurement range via AIN2: 0-35 V (battery voltage divider ratio: 1:10)
• Antenna connector: IPEX4
• Compatibility: 2.4GHz ACCESS / ACCST D16 transmitters

Advanced 8-channel 2.4GHz simultaneous dual-frequency Twin 2.4GHz telemetry receiver. It has 8 high-precision PWM channels and 16 or 24-channel modes via S.BUS. Two detachable antennas with IPEX4 connector provide full signal strength over a range of up to tens of kilometers. It is especially ideal for gliders, but you can also use it for other various models. With redundancy support, it can be connected as a primary receiver via S.BUS. With the Twin 2.4GHz protocol, both receivers work fully simultaneously in this setup. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices, providing bidirectional data transmission via a single cable.

It features advanced interference suppression for reliable, stable signal transmission across the entire range. Smart transmission system matching speeds up pairing. The black box function stores essential flight data. Receiver operating statuses are indicated by an LED indicator. Smart pairing allows firmware updates wireless.

Features:

• Increased protection against RF interference and more stable RF transmission
• Simultaneous Twin 2.4GHz dual frequency transmission system with smart pairing
• Black box function
• High maximum operating range
• Wireless firmware updates (OTA)
• 8 high-precision PWM channels
• S.BUS output port (16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• F.BUS / S.Port

Technical specifications:

• Frequency: simultaneous dual 2.4 GHz
• Dimensions: 54×20×10 mm (L*W*H)
• Weight: 9.8 g
• Operating voltage: 3.5–10 V (supply voltage min. 2.8 V).
• Operating current: 80 mA at 5 V
• External voltage measurement range via AIN2: 0–35 V
• Antenna connector: IPEX4
• Compatibility: 2.4 GHz dual-frequency simultaneous transmission system

Advanced 8-channel 2.4GHz simultaneous dual-frequency Twin 2.4GHz telemetry receiver. It has 8 high-precision PWM channels and 16 or 24-channel modes via S.BUS. Two detachable antennas with IPEX4 connector provide full signal strength over a range of up to tens of kilometers. It is especially ideal for gliders, but you can also use it for other various models. With redundancy support, it can be connected as a primary receiver via S.BUS. With the Twin 2.4GHz protocol, both receivers work fully simultaneously in this setup. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices, providing bidirectional data transmission via a single cable.

It features advanced interference suppression for reliable, stable signal transmission across the entire range. Smart transmission system matching speeds up pairing. The black box function stores essential flight data. Receiver operating statuses are indicated by an LED indicator. Smart pairing allows firmware updates wireless.

It is equipped with a variometer that provides more accurate and faster measurement and transmission of altitude and vertical speed data. It also allows quick audio feedback from the variometer to the Twin 2.4GHz transmitters.

Features:

• Increased protection against RF interference and more stable RF transmission
• Simultaneous Twin 2.4GHz dual frequency transmission system with smart pairing
• Black box function
• High maximum operating range
• Wireless firmware updates (OTA)
• 8 high-precision PWM channels
• S.BUS output port (16/24 channel mode)
• S.BUS input port (with support for redundant connection of 2 receivers)
• F.BUS / S.Port

Technical specifications:

• Frequency: simultaneous dual 2.4 GHz
• Dimensions: 54×20×10 mm (L*W*H)
• Weight: 9.8 g
• Operating voltage: 3.5–10 V (supply voltage min. 2.8 V).
• Operating current: 80 mA at 5 V
• Vario - vertical speed measurement range: ±10 m/s
• Vario - altimeter range and resolution: -700 m to 10,000 m, 0.1 m
• External voltage measurement range via AIN2: 0–35 V
• Antenna connector: IPEX4
• Compatibility: 2.4 GHz dual-frequency simultaneous transmission system

DSM2 Compatible Satellite Full Range Receiver with Sattelite

This DuaLink receiver simultaneously gathers information from two receivers that is processed by patent pending for Spektrum software that combines it to form the most vivid picture of an RF signal.
This dual path redundancy, plus the fact each of the two receivers is located in a slightly different location, exposes each to a different RF environment and creates a bulletproof RF link in all conditions.

Specifications:
Channels: 6 channels
Modulation: DSM2/DSM
Band: 2.4GHz
Voltage Range: 3.5-9.6V

This product is perfectly compatible with JR and Spektrum DSM-X and DSM2 remote controls, including: JR12X, 11X, X9503, X9303/Spektrum DX10t, DX8, DX7s, DX7se, DX6i.

Excellent signal reception: Receiver is equipped with a special antenna with 3dbi gain and an internal 15dB gain amplifier, with strong anti-interference capability and longer signal range.

6CH + PPM: 6 channels plus 1 extra PPM channel, for those who want to fly multiple axes, it is more convenient to get it done in one line.

DSM-X (Supports DSM2)
Input Voltage: 3.5-9.6V
Weight: 12g
Size: 47*24 *14mm

-With a special 3dbi gain antenna, with a built-in amplifier of 15dbi gain.
-Stronger anti-interference, longer distances (up to 2km)
-Supported PPM channel
-No need for additional satellite, more convenient.
-Supported JR Spektrum DSM-X and DSM2 protocols

Spektrum DSM2 DSMX Compatible Satellite Full Range Receiver. works with Spektrum and JR in DSM2/DSMX Modes.

Modulation: DSM2-DSMX Compatible
Band: 2.4 GHz
Dimension: 1.7(L) x 1.5(W) x 1(H) mm
Weight:3 gram
Voltage Range: 3.3V from Receiver

Compatible with multiple flight control NAZA32/CC3D/KK2/F3/Multiwii-APM/V-Bar-5.3

The TBS CROSSFIRE is a long range R/C link based on the newest RF technology, capable of self-healing two-way communications and range beyond comprehension. With a sensitivity of -130dB, full RF-side diversity, tiny receivers for FPV quads, the TBS CROSSFIRE contains the most modern technology to provide a superior long range control link

The Crossfire Micro TX borrows the core technology from its larger brother, but is a JR-module transmitter simplified to the most sought-after features, at a killer price! For people looking to do extreme long range flights beyond 15-20km, the Crossfire TX is still the way to go. For anyone looking to penetrate buildings, fly mini quads or just explore your surroundings a few kilometers away, the Micro TX is the perfect companion. It will still go out up to 40km, just like its bigger brother. But it costs less than half the price.

 Features:

•     Long range, adaptive and robust remote control system for your aircraft
•     Immune to on-board noise
•     Two-way communication link with real-time link vitals and telemetry
•     Self-healing & frequency hopping (DSSS, FHSS)
•     Adaptive bandwidth control and range optimization
•     RX beacon mode to recover your downed aircraft
•     Super easy binding and configuration via built-in display of your R/C
•     Low latency, 150Hz update rate (3x faster than typical RC links) control for perfect immersive feeling
•     Two receiver models: 8 port Diversity Rx, 4 port Mini-receiver (4g weight!)
•     8 or 12ch output via SBUS/PPM/CRSF on both receivers
•     Ability to fly with multiple friends at the same time (10 or more)
•     Selectable RF power from 25mW to 250mW (local restrictions apply)
•     Transmitter LED shows link health
•     Micro-receiver for smaller drones. Smaller than you think!
•     Software updates via RF Link

 
Technical specifications:

•     Frequency Band: 868MHz- EU
•     Input Voltage: 6.0 - 13V
•     Connector : USB-C
  
•     Power consumption: 1.1W (@10mW) - 2W (@100mW)
•     Dimensions: 65 x 48 x 22 mm (JR module size)
•     Weight: 48g

Package includes

• 1 x TBS Crossfire Micro TX V2
• 3 x TBS Crossfire Nano RX
• 3 x TBS Crossfire Micro Receiver Antenna
• 3 x TBS Crossfire Immortal T V2 Antenna
• 1 x Taranis QX7 Mod
• 3 x Cables and Shrink Tubes set

TBS Crossfire nano RX for people who want to save space and solder. Full range, designed specifically for mini- and micro-quads! The Special Edition (SE) includes the TBS Immortal-T V2 Antenna!

TBS is stepping up the Long Range / UHF game, with no competition in sight! With the TBS Crossfire Nano RX we condense 2 years of engineering experience, listening to our customer requirements, and pushing ourselves to the maximum (or in this case, the minimum!). The end result is a full range receiver, at the smallest size of any receiver in the industry (yes, it’s smaller than the XM+).

SPECIFICATIONS

• Weight: 0.5g (receiver only)
• Size: 11mm x 18mm
• Requires: Firmware V2.25
• Input power : 3.3-8.4V
  

INCLUDES

• 1x TBS Crossfire Nano Receiver
• 1x TBS Crossfire Immortal T V2 Antenna
• 1x Spare shrink tube
• 6x 30awg silicon connection wires (2 black, 2 red, 1 white, 1 yellow)
• 1 x pin header 1×4

What could be better than the best Crossfire receiver and an improved Unify Pro32 video transmitter making sweet love? Exactly! Nothing, nothing at all.

Introducing the TBS Crossfire Sixty9, a VTx and RC receiver AIO board sporting a race-friendly, long-range capable video transmitter combined with the same on the TBS Crossfire side. Mounting holes are 20x20, but we do incldue adapters for your 30x30 stacks, and a plastic case for mounting the unit to your frame, without any stacking necessity.

Outputs 2x CRSF + 2x PWM (or 6x PWM) directly to your FC. The main JST-SH connector connects to your flight controller and video camera (or also FC for those that like the FC-OSD).

FEATURES:

• Integrated video transmitter control with long range and (team-)race functions
• Dedicated low-noise power supply for receiver and video transmitter
• Sleek 20x20 mounting form factor
• Plug&play connection and solder pads connectivity
• 3 different mounting flavors, RF tin shields, and other accessories included
• High power analog adjustable video transmitter (up to 1W with perfect cooling)
• 5V regulator bulti-in, takes up to 6S

SPECIFICATIONS

CRSF  :V3 ready
Weight 4.1g (board only)
Antenna ports : 1x video transmitter, 1x R/C receiver
Size : 24mm x 24mm
Input voltage : 6V - 25V (2-6S)
Requires Firmware V4.62 and above
VTX Table for Betaflight

INCLUDES

1x TBS Crossfire Sixty9
1x TBS Crossfire Immortal-T antenna
1x u.FL to SMA mount (for VTx)
1x 30x30 heatsink / case
1x 20x20 heatsink / case
1x optional tin-shield (for added low-noise tolerance)
1x JST-SH x 9 connector

A super-tiny, super-lightweight UHF long range receiver. Perfect match for your mini- or micro-quads as well as 4ch aircraft. It now comes with a servo-adapter board for high-current servos and 4ch PWM connectivity (requires software update to your Crossfire TX!)

Weight: 3.32g(V2)

SIze:4x1.4x0.95(cm)

Includes

    1x TBS Crossfire Micro Receiver
    1x TBS Crossfire Micro RX Adapter
    1x TBS Crossfire Micro RX Adapter Cable
    1x Spare antenna
    1x Spare shrink tube
    1x TBS Vendetta(BST) cable
    1x TBS Powercube cable
    1x Standard RC cable