Receivers

Jeti Central Box 400 with magnetic key

The Central Box 400 is a switchboard designed for the complete management of servos in large to giant models with an emphasis on safety. The Central Box 400 has a unique design that provides overload protection at each servo output. An independent, very powerful BEC (battery eliminator circuit) for each battery input makes the Central Box an optimal solution to connect up to 24 servos. The Central Box 400 can manage the batteries and fully supports the JETI EX telemetry system. Up to two receivers with serial (PPM, EX Bus, UDI) output can be connected to the Central Box 400. With a JETI DC/DS transmitter, the full potential of the Central Box can be used, such as easy configuration of the Central Box, EX telemetry, and very fast servo response.

Central Box 400 supports up to 24 protected servo outputs, two battery inputs with voltage regulators and incorporates  possibility to connect an RC or magnetic switch.

Attributes:

• Two independent high-powered BEC´s for voltage stabilization of servos
• Overload protection on each channel
• Overload protection on Rx, Ext, and Switch outputs
• Possibility to connect up to 2 receivers with serial interface (PPM, EX Bus, UDI)
• Built-in Expander function for up to 4 sensors
• Input for magnetic switch or RC switch
• MPX battery input connectors: 2x
• Stabilized voltage output via a pair of MPX connectors
• 100Hz mode of servo outputs (10ms period)
• Supports EX telemetry (voltage, current, capacity, and temperature measurement, overload indication, ...)
• Easy settings changes via DC/DS transmitter
• Internal memory for storage of telemetry data
• USB connectivity for connection to PC
• Easy settings changes via DC/DS transmitter
• Firmware updatable
• Suitable for use with high voltage (HV) servos
• Robust metal construction with mounting holes
• LED status indication
• Each output is individually configurable (channel assignment, trim, reverse, ATV)

Specication:

• Weight [g]     270
• Dimensions [mm]     131 x 88 x 19
• Sustained current [A]     30
• Number of channels     32
• Telemetry     Yes
• Operational temperature [°C]     -20 ... 75
• Compatible protocols     EX Bus, PPM
• Supply Voltage [V]     6 ... 17
• Satellite receiver support     Yes
• Batteries NiXX     6 ... 12
• Batteries LiXX     2 ... 4
• Voltage BEC [V]     5 ... 8
• Idle current [µA]     60
• Number of battery inputs     2
• Voltage stabilization     Yes
• Peak current (2s) [A]     230

Jeti Central Box 400 with two satellite receivers Rsat 2 and with RC Switch

The Central Box 400 is a switchboard designed for the complete management of servos in large to giant models with an emphasis on safety. The Central Box 400 has a unique design that provides overload protection at each servo output. An independent, very powerful BEC (battery eliminator circuit) for each battery input makes the Central Box an optimal solution to connect up to 24 servos. The Central Box 400 can manage the batteries and fully supports the JETI EX telemetry system. Up to two receivers with serial (PPM, EX Bus, UDI) output can be connected to the Central Box 400. With a JETI DC/DS transmitter, the full potential of the Central Box can be used, such as easy configuration of the Central Box, EX telemetry, and very fast servo response.

Central Box 400 supports up to 24 protected servo outputs, two battery inputs with voltage regulators and incorporates  possibility to connect an RC or magnetic switch.

Attributes:

• Two independent high-powered BEC´s for voltage stabilization of servos
• Overload protection on each channel
• Overload protection on Rx, Ext, and Switch outputs
• Possibility to connect up to 2 receivers with serial interface (PPM, EX Bus, UDI)
• Built-in Expander function for up to 4 sensors
• Input for magnetic switch or RC switch
• MPX battery input connectors: 2x
• Stabilized voltage output via a pair of MPX connectors
• 100Hz mode of servo outputs (10ms period)
• Supports EX telemetry (voltage, current, capacity, and temperature measurement, overload indication, ...)
• Easy settings changes via DC/DS transmitter
• Internal memory for storage of telemetry data
• USB connectivity for connection to PC
• Easy settings changes via DC/DS transmitter
• Firmware updatable
• Suitable for use with high voltage (HV) servos
• Robust metal construction with mounting holes
• LED status indication
• Each output is individually configurable (channel assignment, trim, reverse, ATV)

Specication:

• Weight [g]     270
• Dimensions [mm]     131 x 88 x 19
• Sustained current [A]     30
• Number of channels     32
• Telemetry     Yes
• Operational temperature [°C]     -20 ... 75
• Compatible protocols     EX Bus, PPM
• Supply Voltage [V]     6 ... 17
• Satellite receiver support     Yes
• Batteries NiXX     6 ... 12
• Batteries LiXX     2 ... 4
• Voltage BEC [V]     5 ... 8
• Idle current [µA]     60
• Number of battery inputs     2
• Voltage stabilization     Yes
• Peak current (2s) [A]     230

Jeti DSM10 Dual switch Mixer

DSM 10 is an electronic switch for switching of two receiver batteries which are connected to one receiver.
The product also includes a receiver current supply switch.
Batteries that are connected to the inputs of the DSM 10 are permanently measured and connected with the aid of a hysteresis comparator either both to the output, or one of both batteries with the higher voltage only.
The DSM 10 exit consists of a MPX connector which can be used for direct connection of the exit to the receiver.
The MPX connector is a fixed part of Duplex receivers with the label EPC (External Power Connector), receivers R14 and R18.

The DSM 10 is not equipped with a voltage stabilizing circuit for the connected batteries.
The voltage at the DSM 10 output will always be equal to the voltage of the connected battery with the higher voltage.
Make sure that receiver, servos and other equippment supplied by the DSM 10 are designed for the given voltage.
The DSM 10 is controlled by a magnetic switch which can be placed outside of the model airplane fuselage.
By touching with a special magnet, the system becomes switched on or off.
The electronic switch in switched on state is characterized by a minimum transitional resistance.

 

 

Jeti 6 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers. For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
The REX receivers are fully compatible with the previous generation of the Duplex equipment.

Specification:

• Weight [g] 11
• Dimensions [mm]    38 x 25 x 11
• Number of channels 6
• Telemetry Yes
• Operational temperature [°C]     -10 ... 85
• Compatible protocols     DUPLEX 2.4GHz EX, EX Bus
• Antenna Length [mm] 2 x 100
• Supply Voltage [V] 3,5 - 8,4
• Average Current [mA] 75
• Satellite receiver support Yes
• Output Power [dBm] 15
• Receiver Sensitivity [dBm] -106
   

 Jeti Duplex 2.4EX R18 receiver including RSat2 satellite receiver.

Power can be supplied via the built-in MPX connector, which is compatible with the Jeti Max BEC 2, or via JR/UNI connectors. The power supply voltage required is 3.2-8.4V, but please note that this voltage is not regulated, so please ensure the input voltage is regulated appropriately according to your servo specification.

The R18 includes a single RSAT2 satellite receiver with dual antennae, which should be operated in clone mode with the PPM output mode of the satellite set to 'DIRECT' and the PPM input mode of the R18 set to PPM Input on your chosen satellite channel.

As with all Jeti Duplex 2.4GHz receivers, an audible alert can be configured so that the Duplex transmitter module emits an alarm, should the receiver supply voltage drop below a preset level. This is configurable by connecting the Jeti Box to the Tx module and this particular feature requires no additional sensors.

Complete with bind-plug and MPX plug with two pieces of heatshrink.
For a stable and reliable power source, we recommend the Max BEC range of voltage regulators. Alternatively you may wish to use two A123 LiFePO4 batteries, depending on your power requirements.

Technical Details for Jeti Duplex 2.4EX R18 Receiver

• Dimensions (mm)    62x38x16
• Antennae Count    2
• Antennae Length    400.00mm (15.75")
• Channel Outputs    18
• Temperature Range min. (°C)    -10
• Jeti Box Compatible (JBC)    Yes
• Temperature Range max. (°C)    85
• Supply Voltage min.    3.2V
• Supply Voltage max.    8.4V
• Average Current (mA)    40
• Transmission of Telemetric Data    Yes
• Satellite receiver support    Yes
• Power output (dBm)    20
• Receiver Sensitivity (dBm)    -106
• Weight    34.0g (1.2oz.)

9 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors.

The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

Specification

• Weight [g]:  13
• Dimensions [mm]: 48 x 23 x 10
• Number of channels: 9
• Telemetry: Yes
• Operational temperature [°C]: -10 ... 85
• Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
• Antenna Length [mm]: 2 x 200
• Supply Voltage [V]: 3,2 - 8,4
• Average Current [mA]: 30
• Satellite receiver support: Yes
• Output Power [dBm]: 15
• Receiver Sensitivity [dBm]: -106

A completely new type of receiver from the REX SLIM series with 7 servo slots. The receivers are specially designed for models with very narrow fuselages (e.g. F3J, F5J, etc.).

The REX Slim receivers offer all the features of the well-known REX receiver series with a minimal cross-section.

- supported protocols: PPM, EX BUS, EX Telemetry, S.Bus

- freely programmable channel assignment of the slots

- compact dimensions

- full range

- wireless programmable via the device overview of the Duplex DC/DS transmitters

- programmable via the JETIBOX

Technical data

Dimensions: 15 x 12.5 x 60mm

Weight: 12 g

Supply voltage: 3.5 - 8.4V

Telemetry: Yes

Stabilization ASSIST: No

Servo slots: 9

Antenna length: 2x 200 mm

Scope of delivery

1 DUPLEX 2.4EX Receiver REX 9 Slim

Jeti Duplex 2.4EX R9 channel full-range receiver W/antenna 40cm

Programmable duplex 2.4EX 9 channel receiver 2.4GHz:

Bi-directional communication with the transmitter
Transfer of the telemetry data to the transmitter (read out via the JETIBOX)
Receiver supply voltage indication at the transmitter, and adjustable value for triggering an alarm
A plurality of receivers to a transmitter possible receivable up to a total of 16 channels
Adjustable Failsafe
Servo channels freely assignable
Servo lanes, center position and duration adjustable
free mixers allocation of channels
Expo the channels can be set
Activation within a quarter second after switching
Connection for sensors (8 channel expander bix to 8 sensors)
Programmable with the JETI Box directly or wireless via transmitter

DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and compatible, of course, full of the previous components .
The EX Series provides a significant extension of the possibilities for the transmission of telemetry data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor receive user-friendly design a better overview of the operational status of your model, facilitating the setting of the system components and the way an easier processing, imaging and analysis capability of the (recorded) flight data

Specifications:

• Dimensions 23x48x9,5mm
• Weight     13g
• Antenna length     2x 400mm
• Outputs 9
• Temperature range -10 to 85 ° C
• Input voltage     3.2 - 8.4V
• Average power consumption 40 mA
• Real-time telemetry transmission Yes
• Programming JETIBOX
• Satellite receiver Yes
• Transmission power 20 dBm
• Receiver Sensitivity -106 dBm

Alarm settings:
With the JETI Box alarm signals can be activated at (beeps by duplex RF module in the transmitter):
Alarm waste Receiver supply below a set voltage value

By connecting a current and voltage sensor to the receiver alarm can be triggered by:

• Exceed a current value
• Undershooting of a voltage value
• Exceed a capacitance value

JETI DUPLEX 2.4EX RC Switch

RCSW - RC Switch is a wireless switch designed especially for JETI model products (BEC stabilizers, Central Box and other accessories) that increase the comfort of model control. RC Switch can be easily controlled using DC/DS transmitters and it can be simply used as a replacement of the magnetic key.

Compatible devices: SBEC 40, DPS 40, SPS 20, DSM 10, Central Box 200, Central Box 400, Master Switch etc.

Switching is indicated by a green LED that is visible through the opening on the side of the RC Switch.

Setting the polarity of the switch is specific for each JETI model product, in the chart below there is a list of several supported devices and their RC Switch settings for DC and DS transmitters.

Duplex revolutionary, fully digital 2.4GHz, frequency hopping radio system is fully designed and manufactured by Jeti Model in the Czech Republic. We are excited to introduce two brand new lines of REX and REX Assist Jeti Duplex 2.4GHz Receivers with built-in revolutionary features: Internal Data Telemetry Logging (Black Box), Integrated Multi (3) Input/Output Telemetry & EX Bus Expander, and New 32 Bit Microprocessors (No limits for Future Firmware Upgrades). All Jeti receiver features wireless programmable fail-safe and integrated digital telemetry (Rx Voltage, Signal Quality).

The REX Assist receivers enhance the REX series of receivers and extend it with the intelligent flight stabilization feature, which is designed for airplane models and multi-copters. This stabilization works in all three axes of the model and facilitates flying in windy or otherwise challenging conditions. Aerobatic maneuvers will be more accurate and smoother. With the help of several flight modes, which are also suitable for beginner pilots, flying practice will be really easy.

Variometer is a system that measures atmospheric pressure and using the obtained data, it calculates the altitude above sea level, airspeed, and the rate of climb as well as the rate of descent. Changes in climb and descent rates are signaled as well. The sensor also alerts you if any alarm setting is exceeded.

Features:
- Up to 16 Stabilized Individual Channels
- Different Multicopter Types, from Tricopters to Octocopters
- Up to 3 Adjustable Flight Modes, Options for Stabilizing the Horizon and Altitude
- Optional Variometer Function (Requires Software Module Purchase)
- In-flight Gyro Gain Tuning Using Available Channels
- Latest 3-axis Gyroscope, 3-Axis Accelerometer and Barometric Altimeter
- Support for External Ultrasonic Altimeter
- Support for LED Light Strip, and External Camera Gimbal
- Intelligent Fail-safe, and Vibration Analysis
- Wireless Transmitter programming and PC Support
- Available Telemetry: Rx Voltage, Signal Quality/Strength, G-Force, Attitude Orientation

The REX A receivers enhance the REX series of receivers and extend it with the intelligent flight stabilization feature, which is designed for airplane models and multicopters. This stabilization works in all three axes of the model and facilitates flying in windy or otherwise challenging conditions. Aerobatic maneuvers will be more accurate and smoother. With the help of several flight modes, which are also suitable for beginner pilots, flying practice will be really easy.

The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.

An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

DUPLEX System EX is fully compatible with the previous version of the DUPLEX.

FEATURES

- Integrated telemetry: Rotation angle on 3-axis, G-Force, temperature
- Integrated ASSIST stabilization system 
- For model airplanes and multicopter
- Integrated to connect Expander up to 3 sensors
- Protocol support: PPM, EXBUS, EX,..
- Programmable output pins
- Supports commands
- Compact dimensions
- 32 bit processor
- Full range
- Programmed via  Duplex DC/DS transmitters or with Jeti Studio via PC
- Number of output channels: up to 12- Number of EXT inputs: up to 3
- Dimensions [mm]: 51x28x11
- Weight [g]: 24- EPC (MPX) power connector

6 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors or by the external MPX connector.

Antenna length: 40cm

The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

DUPLEX System EX is fully compatible with the previous version of the DUPLEX.

• Weight [g]: 11
• Dimensions [mm]: 45 x 24 x 12
• Number of channels:6
• Telemetry: Yes
• Operational temperature [°C]: -10 ... 85
• Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
• Antenna Length [mm]: 2 x 400
• Supply Voltage [V]: 3,2 - 8,4
• Average Current [mA]:40
• Satellite receiver support: No
• Output Power: 15 dBm
• Receiver Sensitivity: -106 dBm

JETI Duplex R7 Nano Receiver Weight [g] 1 (2) Dimensions [mm] 30 x 18 x 5 Number of channels 7 Telemetry Yes Operational temperature [°C] -10 ... 85 Compatible protocols DUPLEX 2.4GHz EX, EX Bus Antenna Length [mm] 1 x 32 Supply Voltage [V] 3,2 - 8,4 Average Current [mA] 30 Satellite receiver support No Output Power [dBm] 6 Receiver Sensitivity [dBm] -98

Jeti Duplex receiver 2.4EX R18 2.4GHz

18 channel full-range receiver compatible with Jeti EX & EX bus protocols. Support telemetry functions. Power supply is provided by MPX connector or standard JR connectors.

Additional features:
PPM input (Sat1)
PPM input or output (Sat2)
Jeti Duplex Rsat2 is included in the package

The DUPLEX EX line of receivers is Intended for surgery with DUPLEX Tx transmitter modules in the 2,4GHz band-and are fully compatible with the previous version of the DUPLEX.
Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely Call new aspects in the model remote control branch.
One of the most important advantages is the operational without crystal, more over the low susceptibility towards interference, the high range up to the limit of visibility and the Possibility to follow anytime the onboard state of the model and its functional parts.
This PPM signal is ford heron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment Which requires a PPM signal at the input.

DUPLEX EX system is fully compatible with the previous version of the DUPLEX.

Specification:

• Manufacturer: Jeti
• Quiescent current [mA]: 40
• Receive Sensitivity [dBm]: -106
• Antenna number: 2    2
• Antenna length [mm]: 400
• channels: 18
• Satellite receiver possible
• Real-time telemetry
• Transmission power [dBm]: 20
• Type:     duplex EX
• Rated voltage up to [V]: 8.4
• Rated voltage [V]: 3.2
• Weight [g]: 30
• Height [mm]: 16
• Width [mm]: 38
• Length [mm]: 62

Jeti Duplex receiver 2.4EX REX3 with 20cm antenna

DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and , of course, fully compatible with the existing components .
The EX Series provides a significant expansion of the possibilities of transmission of telemetric data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor software user-friendly way a better overview of the operational status of your model, a facilitated setting the system components and the way a facilitated processing, imaging and analysis possibility of (recorded) flight information.

Programmable Duplex 2.4EX REX3 receiver 2.4GHz:

• bi-directional communication with the transmitter
• Transfer of telemetry data to the transmitter
• Voltage indicator Receiver supply at the transmitter and adjustable value for triggering an alarm
• multiple recipients possible at a transmitter, be received up to 16 channels
• Adjustable Failsafe
• Servo channels freely assignable
• Servo travel center position and duration adjustable
• free mixer channels are assigned
• Expo of the channels can be set  
• internal memory for data logging and
• control signals
• integrated expander for up to 3 sensors
• Supported protocols: PPM
• , EXBUS, EX, ..
• programmable features of the slots
• support the direct entries
• compact dimensions
• 32 bit processor
• full coverage
• programmable via the JETIBOX and wirelessly
• via the duplex DC / DS transmitter

Specifications:

• Dimensions: 40x22x7mm
• Weight:  7.5g
• Antenna length: 2x 400mm
• Outputs: 3
• Temperature range: -10 To 85 ° C
• Input voltage: 3.2 - 8.4V
• Average current consumption:  mA
• Real-time telemetry: Yes
• Programming: JETIBOX
• Satellite receiver: Yes
• Transmission power: 15 dBm
• Receive Sensitivity: -106 dBm

Jeti Duplex receiver 2.4EX REX3 with 40cm antenna

DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and , of course, fully compatible with the existing components .
The EX Series provides a significant expansion of the possibilities of transmission of telemetric data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor software user-friendly way a better overview of the operational status of your model, a facilitated setting the system components and the way a facilitated processing, imaging and analysis possibility of (recorded) flight information.

Programmable Duplex 2.4EX REX3 receiver 2.4GHz:

• bi-directional communication with the transmitter
• Transfer of telemetry data to the transmitter
• Voltage indicator Receiver supply at the transmitter and adjustable value for triggering an alarm
• multiple recipients possible at a transmitter, be received up to 16 channels
• Adjustable Failsafe
• Servo channels freely assignable
• Servo travel center position and duration adjustable
• free mixer channels are assigned
• Expo of the channels can be set  
• internal memory for data logging and
• control signals
• integrated expander for up to 3 sensors
• Supported protocols: PPM
• , EXBUS, EX, ..
• programmable features of the slots
• support the direct entries
• compact dimensions
• 32 bit processor
• full coverage
• programmable via the JETIBOX and wirelessly
• via the duplex DC / DS transmitter

Specifications:

• Dimensions: 40x22x7mm
• Weight:  7.5g
• Antenna length: 2x 400mm
• Outputs: 3
• Temperature range: -10 To 85 ° C
• Input voltage: 3.2 - 8.4V
• Average current consumption:  mA
• Real-time telemetry: Yes
• Programming: JETIBOX
• Satellite receiver: Yes
• Transmission power: 15 dBm
• Receive Sensitivity: -106 dBm

Jeti Duplex Satellite for Type R.sub.sat 900

Only the DC 24 transmitter have a backup transmission system for the highest data transfer security and reliability.
It therefore represents the first dual-band radio system RC new generation.

Specification:

• Weight (g): 11
• Dimensions (mm): 0x22x7
• Temperature range (° C): -10 - 85
• Voltage range (V): 3.2 to 8.4
• Current consumption (mA): 30
• Frequency range (MHz):     863-870
• Logs:     EX-bus, PPM, UDI

Satellite receiver for Duplex R9, R10, R11EPC, R12EPC, R14 and Duplex R18 (connection by cable). PPM output is available on a single line.

The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks

to the fully digital and bidirectional communication between

transmitter and receiver there arise completely new aspects in the model

remote control branch. One of the most important advantages is the

operation without crystal, moreover the low susceptibility towards

interference, the high range up to the limit of visibility and the

possibility to follow anytime the onboard state of the model and its

functional parts.
An additional satellite receiver RSat2 complements

the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full

DUPLEX system receiver offering the complete functional spectrum of the

system. Instead of classical servo pulses the output of the RSat2

receiver offers a PPM signal only. This PPM signal is further on

processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible

RC equipment which requires a PPM signal at the input.

DUPLEX EX System is fully compatible with the previous version of the DUPLEX.

Weight [g] 6
Dimensions [mm] 38 x 20 x 7
Number of channels 16
Telemetry Yes
Operational temperature [°C] -10 ... 85
Compatible protocols DUPLEX 2.4GHz EX, EX Bus
Antenna Length [mm] 2 x 200
Supply Voltage [V] 3,2 - 8,4
Average Current [mA] 30
Satellite receiver support No
Output Power [dBm] 15
Receiver Sensitivity [dBm] -106

Jeti Enlink 2RS

EnLink 2RS is a device for increasing safety and reliability of radio controled models to the highest level. Parallel connection of systems that are detached maximally leads to the significant increase in reliability.
EnLink2RS is constructed especially for installing to systems with parallel sorting of two receivers in the model.

Jeti Receiver Duplex 2.4EX R11EPC 2,4GHz

11 channel full-range receiver compatible with JETI EX & EX Bus
protocols. Supports telemetry functions and contains a separate battery power connector.

Additional features:

• PPM
• input (Sat1)

The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM
signal only. This PPM
signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM
signal at the input.

DUPLEX System EX is fully compatible with the previous version of the DUPLEX.

Manuals - Duplex EX

• JETI Duplex EX Receiver Manual V3.22 [EN, DE] - English & German user manual for the receivers version 3.22 (6/2014)
• Declaration of Conformity CZ+EN - Standards compliance
• JETI Duplex EX Manual V3.0 EN+DE - English & German user manual for Tx modules and receivers (6/2011)Rx + RSat Jetibox Schema V3.0 CZ - Jetibox screen schemes of the receivers and satellites
• Rx + Rsat Jetibox Schema V3.0 EN+DE - Jetibox screen schemes of the receivers and satellites

Update - Receivers

• Duplex EX - Rx V3.22 - Rx Firmware Update (4/2014) - EX Bus
• , Log. inputs/outputs, UDI. RSAT2[3.21]: By default, PPM
• fail-safe is set to "Off". [3.22] Telemetry logical inputs improved.
• Duplex EX - Rx & Tx V3.04 - Rx & Tx Compatibility Firmware Update (3/2012)
• Duplex EX - Rx V3.11 - Rx Firmware Update (5/2013) - EX Bus
• JETI Duplex EX Manual V3.11 EN - English user manual for receivers (4/2013)

Jeti Receiver Duplex 2.4EX R5L 2,4GHz

5 channel full-range receiver compatible with JETI EX & EX Bus protocols. This receiver is designed for operation in small and medium models. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors.
The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is further on processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

DUPLEX  EX System is fully compatible with the previous version of the DUPLEX.

Specification: 

Quiescent current [mA]:    30

• Receive Sensitivity [dBm]:    -106
• Antenna number:    2
• Antenna length [mm]:    100
• Channels:    5
• Satellite receiver possible:    
• Real-time telemetry:    
• Transmission power [dBm]:    15    
• Type:    Duplex EX
• Rated voltage up to [V]:    8.4
• Rated voltage [V]:    3.2
• Weight [g]:    5.4
• Height [mm]:    7
• Width [mm]:    20
• Length [mm]:    47

JETI Receiver Duplex 2.4EX REX12

12 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers.
For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
The REX receivers are fully compatible with the previous generation of the Duplex equipment.

Specification.

• Weight [g] 24
• Dimensions [mm] 51 x 28 x 11
• Number of channels 12
• Telemetry Yes
• Operational temperature [°C]     -10 ... 85
• Compatible protocols DUPLEX 2.4GHz EX, EX Bus
• Antenna Length [mm] 2 x 400
• Supply Voltage [V] 3,5 - 8,4
• Average Current [mA] 75
• Satellite receiver support Yes
• Output Power [dBm] 15
• Receiver Sensitivity [dBm] -106

6 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

The REX A receivers enhance the REX series of receivers and extend it with the intelligent flight stabilization feature, which is designed for airplane models and multicopters. This stabilization works in all three axes of the model and facilitates flying in windy or otherwise challenging conditions. Aerobatic maneuvers will be more accurate and smoother. With the help of several flight modes, which are also suitable for beginner pilots, flying practice will be really easy.

Features:

• Up to 16 stabilized airplane channels.
• Support for different multicopter types – from tricopters to octocopters.
• Up to 3 adjustable flight modes, options for stabilizing the horizon and altitude.
• In-flight gain tuning using free channels.
• Using the latest 3-axis gyroscope, 3-axis accelerometer and barometric altimeter.
• Support for LED strip consisting of WS2812 chips.
• Support for external camera gimbal driven by servos.
• Intelligent fail-safe.
• Vibration analysis.
• Full set-up options with DC/DS transmitters or via PC.
• Available telemetry: Receiver voltage, signal quality, G-force, attitude orientation.
• Support of telemetry and up to 3 sensors connected directly.

Specifications:

• Weight [g]: 11
• Dimensions [mm]: 38 x 25 x 11
• Number of channels: 6
• Telemetry: Yes
• Operational temperature [°C]: -10 ... 85
• Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
• Antenna Length [mm]: 2 x 100
• Supply Voltage [V]: 3,5 - 8,4
• Average Current [mA]: 75
• Satellite receiver support: Yes
• Output Power [dBm]: 15
• Receiver Sensitivity [dBm]: -106
• Assist stabilization: Yes

7 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Antenna length 40cm.

Additional features:

PPM input
PPM output
Integrated expander for EX & EX Bus devices
UDI digital output
JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.

The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.

The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers. For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.

The REX receivers are fully compatible with the previous generation of the Duplex equipment.

• Weight [g]    13
• Dimensions [mm]    42 x 28 x 11
• Number of channels    7
• Telemetry    Yes
• Operational temperature [°C]    -10 ... 85
• Compatible protocols    DUPLEX 2.4GHz EX, EX Bus
• Antenna Length [mm]    2 x 400
• Supply Voltage [V]    3,5 - 8,4
• Average Current [mA]    75
• Satellite receiver support    Yes
• Output Power [dBm]    15
• Receiver Sensitivity [dBm]    -106
• Assist stabilization    No

Jeti 7 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

Additional features:

• PPM input
• PPM output
• Integrated expander for EX & EX Bus devices
• UDI digital output

JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers. For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
The REX receivers are fully compatible with the previous generation of the Duplex equipment.

Specification:

• Weight [g] 13
• Dimensions [mm]    42 x 28 x 11
• Number of channels 7
• Telemetry Yes
• Operational temperature [°C]     -10 ... 85
• Compatible protocols     DUPLEX 2.4GHz EX, EX Bus
• Antenna Length [mm] 2 x 100
• Supply Voltage [V] 3,5 - 8,4
• Average Current [mA] 75
• Satellite receiver support Yes
• Output Power [dBm] 15
• Receiver Sensitivity [dBm] -106

A completely new type of receiver from the REX SLIM series with 7 servo slots. The receivers are specially designed for models with very narrow fuselages (e.g. F3J, F5J, etc.).

• Supported protocols: PPM, EX BUS, EX Telemetry, S.Bus
• Freely programmable channel assignment of the slots
• Compact dimensions
• Full range
• Wireless programmable via the device overview of the Duplex DC/DS transmitters
• Programmable via the JETIBOX

• Integrated ASSIST stabilization system with damping, heading hold, trainer mode...
• Additional, integrated telemetry: rotation angle on 3 axes, G-Force, temperature
• For fixed-wing models and multi-copters
• Can output stabilized EX bus signal for e.g. Central Boxes
• Of course also suitable for delta and flying wing models

Specification:

Dimensions [mm] 60x16x13
Telemetry Yes
Operational temperature [°C] -10 to 85
Compatible protocols DUPLEX 2.4 GHz EX, EX Bus
Average Current [mA] 85
Satellite receiver support Yes
Output Power [dBm] 15
Receiver Sensitivity [dBm] -106
Assist stabilization Yes
Frequency 2400 - 2483 MHz
Weight [g] 13
Number of channels 7
Antenna Length [mm] 2x 200
Supply Voltage [V] 3.5 - 8.4

This type of receiver of the REX SLIM series with 7 servo outputs. The receivers are specially designed for planes with a very small fuselage. Their compact dimensions suit all pilots who are limited by space in the model (eg F3J, F5J, etc.).

The REX Slim receivers offer all the features of the well-known REX receiver series with a minimal cross-section

FEATURES

• Supported protocols: PPM, EX BUS, EX Telemetry, S.Bus
• Freely programmable channel assignment of the slots
• Compact dimensions
• Full range
• Wireless programmable via the device overview of the Duplex DC/DS transmitters
• Programmable via the JETIBOX

Technical data :

• Dimensions: 15 x 12.5 x 60mm
• Weight: 12 g
• Supply voltage: 3.5 - 8.4V
• Telemetry: Yes
• Stabilisation ASSIST: NO
• Servo slots: 7
• Antenna length: 2x 200 mm

Jeti Universal Switch 6A opto

The switch SP 06 opto has been specifically designed for switching purposes of auxiliary functions, such as on board glow plug heating systems and miscellaneous lighting systems etc. in model airplanes, model ships, and model cars. The switched loads can be of ohmic, inductive or capacitive character. The switching moment is signalled by  a LED.

Specification:
 

• Weight [g]: 9
• Dimensions [mm]: 27 x 15 x 5
• Sustained current [A]:   6
• Peak current (max 30s) [A]: 10
• Telemetry: No
• Operational temperature [°C]: -10 ... 70
• Recommended input voltage [V]: 3,5 ... 16
• Input voltage max. [V]:   16

Ultra-light and small 4-channel 2.4 GHz FASST receiver for indoor and Park Flyers.
Weight only 3,9 g, without housing only 3.3 g. No crystals, no frequency channel selection and the highest security against Immediately channel interference from 2.4 GHz FASST technology.
Best suppression of interference by fast frequency hopping. High intermediate frequency of 800 MHz, resistant to electromagnetic signals .
Simple connectivity through integrated EASY-link button. Suitable for all Futaba transmitters from 6-channels ,compatible to work in 7 channel - modulation

Tech specs
operating voltage : 4,8-7,4 Volt
Current: 40 mA
channels: 4
resolution :2048 KHz
Weight: 3,9 g (3.3 gr without case)
size: 35 x 20 x 7 mm

Small, lightweight 2.4 GHz FHSS four-channel receiver incorporating Frequency Hopping technology.

No crystals, no spot frequency selection, and maximum protection from same-channel interference thanks to high-speed 2.4 GHz FHSS technology. High-speed Frequency Hopping for effective suppression of interference signals.
Automatic switching between S-FHSS (High-Speed mode - only in conjunction with digital servos) and FHSS mode.

Frequency Hopping system with thirty channels at 1.5 MHz spacing in the 2404 - 2447.5 MHz range. Maximum 28 simultaneous users.
Not compatible with FASST transmitters. Only for FHSS systems such as T2PL, T3PL, T4YF, T4PL, T6JG)
Not recommended for large-scale model aircraft and jets.
Range: approx. 1000 m

Specification: Channel spacing: 4.00 Weight: 8 g Dimensions: 39 x 26 x 12.5 mm mm Voltage: 4.8-7.4V Volts

R6008-A 2.4GHz FASST compatible 6 channel receiver plastic case changeable double antenna

SPECIFICATIONS:

• 6ch
• Frequency 2.400GHz-2.483GHz
• Input voltage:  3.5-8.4v
• Antenna Length:  145mm(5.65in)
• Weight: 8.2g(0.28oz)
• Size: 35.5x23.3x12.7mm(1.38x0.9x0.5in)
• Signal period: 14ms (mode FS) / 7ms (mode HS)

FEATURES:

• Compatible with FASST 2.4G:Air Systems(7CH Mode/Multi Mode)
• Surface Systems(C1 Mode)
• Stable performance and high receiving sensitivity
• Two selectable failsafe setting options
• Improve capability of anti-interference
• Firmware upgradable

COMPATIBLE:
FASST 2.4G Air Systems(7CH Mode/Multi Mode):6EX,7C,TM-7,TM-8,T8FG,T10C,
TM-10,T10CG,14SG,T12Z,T12FG,TM-14,T14MZ,etc.
FASST 2.4G Surface Systems(C1 Mode):3PK,4PK,etc

R6008-A 2.4GHz FASST compatible 6 channel receiver plastic case changeable double antenna

SPECIFICATIONS:

• 8-13ch
• Frequency 2.400GHz-2.483GHz
• Input voltage:  3.5-8.4v
• Antenna Length:  145mm(5.65in)
• Weight:11.5gr
• Size: 48x15x25
• Signal period: 14ms (mode FS) / 7ms (mode HS)

FEATURES:

• Compatible with FASST 2.4G:Air Systems(7CH Mode/Multi Mode)
• Surface Systems(C1 Mode)
• Stable performance and high receiving sensitivity
• Two selectable failsafe setting options
• Improve capability of anti-interference
• Firmware upgradable

COMPATIBLE:
FASST 2.4G Air Systems(7CH Mode/Multi Mode):6EX,7C,TM-7,TM-8,T8FG,T10C,
TM-10,T10CG,14SG,T12Z,T12FG,TM-14,T14MZ,etc.
FASST 2.4G Surface Systems(C1 Mode):3PK,4PK,etc

Radiolink R9DS, 2.4G 10 channels receiver, DSSS and FHSS spread spectrum working synchronously, use for Radiolink transmitters AT9, AT9S and AT10.
SBUS and PWM signal possible working at the same time

Two signal working mode:

(1)PWM signal output working mode：red LED indicates PWM signal output, 9 channels Totally.
(2) SBUS signal output working mode: blue/purple LED indicates SBUS signal output, 10 channels totally. SBUS and PWM signal possible working at the same time with SBUS signal output working mode. CH9 output SBUS signal, the original CH1 to CH4 output CH7 to CH10 PWM signal at the same time.

SBUS and PWM signal change：

Short press the ID SET switch two times within 1 second, the signal is changed from normal PWM to SBUS. The red LED indicates the normal PWM and blue/purple LED indicates SBUS signal.

How to match code with transmitter:
1. Place the transmitter and the receiver close to each other within 1 meters.
2. Turn on the transmitter, then power on the R9DS.
3. Connect CH3 of R9DS to ESC.
4. There is a black button on the R9DS, use a thin stick press the button twice in two seconds and release, receiver light start blinking, after about 8 times blinking, match code success when receiver signal LED always on!

• Channels: 10 channels S-Bus, 9 channels PWM
• Compatibility: AT9,AT9S, AT10
• Channel output: S-Bus & PWM
• Working voltage: 4.8 - 10v
• Working current: 38 - 45mA @ 5v
• Precision: 4096 , 0.25us per section
• Telemetry: integrate telemetry sensor including signal strength and voltage
• External telemetry: supported by module PRM-01 and module PRM-02

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today pilots have come to expect.

Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built in FW updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.
Tiny in size yet big on features and range the RP series of receivers have you covered.

What’s new on the RP1

Improved PCB design is better for heat dissipation.
Rigid antenna with greater durability and performance.
Solder pads are improved and easier to solder to.
LED on top side of PCB.

Specifications:

• Item Name: RP1 Nano Receiver- LBT EU protocol
• Type: ISM
• ESP8285 MCU
• SX1280IMLTRT RF Module
• Antenna: 65mm 2.4ghz T Antenna
• Frequency Range: 2400 MHz to 2480 MHz
• Maximum receive refresh rate: 500Hz / F1000Hz
• Minimum receiver refresh rate: 25Hz
• Working voltage: 5v
• Weight: 0.53g (without antenna)
• Dimension: 13mm*11mm*3mm
• TCXO: Yes

Please consult Local Telecom regulations when using this item!

Features

• Based on the Revolutionary ExpressLRS System
• High performance, high reliability, flexible configuration, fast response speed and ultra-long range
• Support 8 PWM Channels
• Optimized ground up PCB design
• Automatically voltage telemetry of external battery voltage or built-in receiver voltage
• ER8GV receiver is built-in high-precision air pressure sensor (Vario)
• Supports Wi-Fi updates and WEBUI configuration
• Reserve 4pin CRSF input port
• High quality 2.54 mm connector
• Standard 15 cm High Sensitivity Antenna
• For fixed-wing aircraft and gliders

Specifications:

• Item: ER8G 2.4GHz ELRS PWM Receiver
• Power supply: DC 3.5 - 8.4V
• Antenna type: 15cm high sensitivity antenna
• Wireless protocol: ExpressLRS 3.3.0 pre-installed
• Output channel: 6CH PWM
• Telemetry power: maximum 50mw (LUA can be set)
• Battery voltage detection range: DC 3.0 - 26V
• Weight: 5.0 grams
• Dimensions:42x13x8mm
• Firmware: Device Category: Radiomaster 2.4Ghz / Device: Radiomaster ER8G

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

Please consult Local Telecom regulations when using this item!

Features

• Based on the Revolutionary ExpressLRS System
• High performance, high reliability, flexible configuration, fast response speed and ultra-long range
• Support 8 PWM Channels
• Optimized ground up PCB design
• Automatically voltage telemetry of external battery voltage or built-in receiver voltage
• ER8GV receiver is built-in high-precision air pressure sensor (Vario)
• Supports Wi-Fi updates and WEBUI configuration
• Reserve 4pin CRSF input port
• High quality 2.54 mm connector
• Standard 20 cm High Sensitivity Antenna
• For fixed-wing aircraft and gliders

Specifications:

• Item: ER8G 2.4GHz ELRS PWM Receiver
• Power supply: DC 3.5 - 8.4V
• Antenna type: 20cm high sensitivity antenna
• Wireless protocol: ExpressLRS 3.3.0 pre-installed
• Output channel: 8CH PWM
• Telemetry power: maximum 100mw (LUA can be set)
• Battery voltage detection range: DC 4.0 - 35V
• Weight: 12 grams
• Dimensions: 60*13.5*13mm
• Firmware: Device Category: Radiomaster 2.4Ghz / Device: Radiomaster ER8G

This receiver works with all 2.4GHz ExpressLRS transmitters on the market.