OXY 2,3,Tareq

OXY3 TE Ultra Swashplate Black Orange

OXY3 TE -  Ultra Tail Pitch Slider Black

Packing List:

• 1 x OXY3 - V1-V2 FBL Antirotation Arm, Service Bag

Description:

• Lynx offer a spare bag for Oxy3 Helicopter V1 and V2 Edition

 
Packing List:

• 1 x OXY3 - V1-V2 FBL Head System, Spare Bag

 

Description:

• Oxy Heli in cooperation with Lynx Heli Innovations introduce the new V2 Main Grip System for Oxy 3 heli.
• OXY 3 V2 Edition Main Grips was designed to replace the standard one,  giving in case of crash, a special “save main grip design”.
• Listen to request that after a crash. The DFC lock screw snapping off on the  Main Grip.  Lynx offer now a simple solution, that works perfectly!
• A special spacers sit between the DFC arm and the main grip pitch arm. So in case of a hard crash, the screw can bend or get broken, but still with removing the spacer, will be possible with simple pliers and some heat,  remove the damaged screw and easy reassembly the main grip without the risk to replace the full main grip..
• Low cost spare bag  in case of service need.
• This OXY 3 upgraded Main Grip keep the same performance and precision of the standard one, but helps in case of hard crash.

Features:

• Direct replacement for the standard OXY 3 two blade head parts (Sport, 255, 285 and TE).
• Special spacer design system that save the main grip in case of hard crash.
• Designed tested and approved with very hard head crash tests.
• Perfect upgrade for those who don’t want to worry about a crash!
• Reuse standard Oxy 3 Radial and Thrust Bearing for easy maintenance.
• Low cost spare bag help in case of service need.
• FEA (Final Elements Analysis) design assisted, achieve lightweight and maximum strength.

 

Packing List:

• 1 set Oxy 3 Pro Edition Main Grip Silver preassembly
   

OXY3 - Blade Holder

Content:

• 1 x Oxy3 - Blade Holder

OXY3 - Bottom plate, CF

Content:

• 1 x OXY3- Bottom plate, CF

OXY3-4 CNC Alu DFC Arm Set - Red

PACKING LIST:

• 1 Set x OXY3 - OXY4 CNC Aluminum DFC Arm, Set - RED Color

NOTE:

• Standard Part for OXY 3 Tareq Edtion and Upgrade for any OXY 3 and 4

2 Set x OXY3 - OXY4 DFC Arm Hardware

This spare is compatible for any OXY 3 - OXY 4 - OXY 4 Max

OXY3-4 DFC Arm Set

PACKING LIST:

• 1 Set x OXY3 - OXY4 DFC Arm, Set

NOTE:

• 2018 Edition, compatible with any OXY3 and OXY4

 

1 x OXY3 Anti Rotation Guide

NOTE: compatible with any OXY3

Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand temperatures of up to 200 degrees C (392 F).

All Scorpion HK Series 22mm motors come with 3.5mm male Bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller, heatshrink to cover the bullet connectors and mounting screws. Since the HK series motors are primarily designed for Helicopter and Ducted Fan use, they do not include a prop adapter. If you intend on running a prop on this motor, you will need to purchase a prop adapter for a 3.17mm shaft (1/8 inch).

Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

Specifications:

• Stator Diameter:  22.0 mm
• Stator Thickness:  8.0 mm
• No. of Stator Arms:  9
• Magnet Poles:  6
• Motor Wind:  24 Turn Delta
• Motor Wire:  8-Strand 0.19mm
• Motor Kv:  3590 RPM / Volt
• No-Load Current:  1.21 Amps @ 10 volts
• Motor Resistance: 0.061 Ohms
• Max Continuous Current:  21 Amps
• Max Continuous Power:  220 Watts
• Weight: 39 Grams
• Outside Diameter:  27.9 mm
• Shaft Diameter:  3.17 mm
• Body Length:  25.3 mm
• Overall Shaft Length:  45.7 mm
• Max Lipo Cell:  3s
• Motor Timing:  5deg
• Drive Frequency:  8kHz

Included in the Box:

• 1 x Scorpion HKII-2208-24 Motor
• 3 x Female Connectors
• 3 x Heat Shrink
• 4 x M3 Screws

Xnova "Lightning" 3220-950KV Brushless Motor, an updated powerhouse of a motor for your heli needs. Any helicopter asking for insane power swinging 380-420mm blades will be more than happy with this masterpiece.

Features:

• Improved higher efficiency with thinner stator lamination, designed with integrated cooling system resulting in lower temperature
• Increased power output by use of thicker hand wound YY single strand copper wires, heat resistant up to 250 degrees C
• New type of high-performance neodymium magnets, heat resistant up to 150 degrees C resulting in overall better performance
• 100% hand-wound

Specifications:

Slots & Poles: 12n10p
Winding T: YY
rpm/V: 945
Volt (V): 10 / 22.2
Io(A): 1.8 / 3.0
Rm (mohm): 18 / 18
Weight (without connector): 200g
Body Length (no shaft): 45mm
Diameter: 40.5mm
Shaft Length: 22mm
Shaft Dia.: 5mm
Mounting Holes CTC Distance: 25mm
Mounting Screw: M3x0.5
Max Eff. Curr.: 31.62 / 60.83
Max Eff.: 88.62 / 90.14
Kt (Nm/A): 0.0101
Km (Nm/sqrt(w)): 0.0749
Max Continuous Power(Watts): 1450
Peak Continuous Power(Watts) (2 sec): 1900
Max Continuous Current(Amps): 66

Xnova brushless high performance out runner motor designed for extreme hard 3D, running in 420-500mm blade size helicopter where highest power to weight ratio is important.At the same time this motor is also extreme efficient!

• Improved higher efficiency with thinner stator lamination, designed with integrated cooling system resulting in lower temperature
• Increased power output by use of thicker hand wound YY single strand copper wires, heat resistant up to 250 degrees C
• New type of high-performance neodymium magnets, heat resistant up to 150 degrees C resulting in overall better performance
• 100% hand-wound

Specifications:

Slots & Poles 12n10p
Winding T YY
rpm/V 1100
Volt (V) 10 / 22.2
Io(A) 3.1 / 5.1
Rm (mohm) 10 / 10
Weight (without connector) (g) 240
Body Length (no shaft) mm 50
Diameter (mm) 40.5
Shaft Length (mm) (Details pictures) A
Shaft Dia. (mm) 5
Mounting Holes CTC Distance (mm) 25
Mounting Screw M3x0.5
Max Eff. Curr. 55.68 / 106.40
Max Eff. 88.86 / 90.41
Kt (Nm/A) 0.0087
Km (Nm/sqrt(w)) 0.0868
Max Continuous Power(Watts) 1900
Peak Continuous Power(Watts) (2 sec) 2500
Max Continuous Current(Amps) 86