Miniature Aircraft

Main Shaft Bearing 10 x 26 x 8 (Pack of 1)

Main Shaft Bearing 15 x 24 x 4 (Pack of 1)

Middle Main Shaft Bearing Block w/Bearing V2 (Pack of 1)

Miniature aircraft 90 Degree Fuel Fitting Set, SET OF 1 full 90 degrees fitting

Miniature Aircraft Flybarless (FBL) Whiplash Main Shaft V2 - Pack of 1

1 x 131-408

Fits Whiplash Version 2, Nitro, Electric, Gasser Models, 10mm

Miniature aircraft Furion 6 FBL - Kit version Aluminum Boom Clamps Motor Shaft Lower Bearing Support Optional Pinion Gear Available Removable Battery Tray Flybarless Rotor Head: Full Ball Bearings/Thrust Bearings Heavy Duty Hiller Rods 8mm Head Axle CNC Machined Aluminum Swashplate Hex/Hardened Control Balls CNC Aluminum Head Button CNC Aluminum Blade Grips High Quality Swashplate Heim Ball/Ball Bearing Simple SleekDesign Tail Rotor: Full Ball Bearings Graphite Painted Tail Fin Secure CNC Aluminum Tail Rotor Clamps 22mm Lightweight Aluminum Tail Boom Positive Control System 2mm Control Rod Hardened Tail Rotor Output Shaft Carbon/Aluminum Boom Supports Canopy High Visibility Painted Epoxy-Glass Canopy by Canomod Additional Furion 6 Specifications: 6S Battery Setup Recommended Motor KV Range: 850-900 Gear Ratio: 8.38:1 (12t pinion gear/103t main gear) Battery Size: 6S 5000mah Main Rotor RPM: 2100-2300 Motor Shaft Size: 6mm x 30/32mm 10S Battery Setup Recommended Motor KV Range: 540-560 Gear Ratio: 9.08:1 (11t pinion gear/103t main gear) Battery Size: 2 x 5S 4000-5000mah Main Rotor RPM: 2200-2600 Motor Shaft Size: 6mm x 30/32mm

4000-10 GAS Muffler for ZG 20 - 29 RC / PUH Engines

1 x 4000-10, 2 x 0085-7, 1 x 4000-11

Zimmermann gas muffler for Zenoah, TRM, BH Hanson gas engines. Fits RC and PUH engines from ZG 20 to 300 engines.

Made from stainless steel. Fits Whiplash gasser, Spectra-G, 1005 gasser.

• NEW aggressively-styled, stiffer frames with side-by-side battery mounting for better GC control
• Increased cyclic and tail rate capabilities for more locked-in, slop free controls, and easier battery change-outs.
• 20° helical drivetrain with hardened steel pinion gear and CNC machined main gear.
• Improved gear ratios of 9:1 and 9.75:1 to match today’s motor Kv market.
• Adjustable motor mount for fine tuning gear mesh.
• Steel-sleeved main gear hub eliminates middle bearing block wear.
• True 6061-T6 CNC machined aluminum components
• CNC machined aluminum triple main shaft bearing blocks
• Narrowed tuff strut landing gear
• Ball bearing supported pinion gear
• Improved electronics placement and wiring options

Rotor Head:

Direct controlled 120 (degree) CCPM

Heavy duty linkages

9mm head axle

CNC machined aluminum swashplate

CNC machined main rotor grips

CNC machined main rotor head

High quality swashplate heim ball/ball bearing

Tail Rotor:

Full ball/thrust bearings

Graphite tail fin

CNC aluminum “open” gearbox

Carbon 22mm tail boom

Hardened tail rotor output shaft

Carbon/Aluminum boom supports and CNC machined aluminum boom clamps

Model Specifications:

Length: 52.5" (1333mm)

Height: Flybar - 6.5” (419mm)

Rotor Span: 1561-1601mm - 690-730mm blades

Tail Rotor Span: 286mm with 105mm T/R blades

Avg. Ready-to-Fly Weight: 11.5-12.5lbs - 5.22-5.67kg (w/batteries)

Main Rotor Blades: 690-730mm

Power: 12S, 490-560KV

• NEW aggressively-styled, stiffer frames with side-by-side battery mounting for better GC control
• Increased cyclic and tail rate capabilities for more locked-in, slop free controls, and easier battery change-outs.
• 20° helical drivetrain with hardened steel pinion gear and CNC machined main gear.
• Improved gear ratios of 9:1 and 9.75:1 to match today’s motor Kv market.
• Adjustable motor mount for fine tuning gear mesh.
• Steel-sleeved main gear hub eliminates middle bearing block wear.
• True 6061-T6 CNC machined aluminum components
• CNC machined aluminum triple main shaft bearing blocks
• Narrowed tuff strut landing gear
• Ball bearing supported pinion gear
• Improved electronics placement and wiring options

• This is a super combo, including the following components
  Whiplash 730E Kit
  Blades 710( Mah/Edge/Rotortech). as stock allows
  Tail blades 105mm- brand depends on stock
  Scorpion Motor HK4035-500 OR 560kv
  ESC Tribunus II 12-130A
  (3) Cyclic SERVO Savox TG(1257/8) or KST 725/BLS 905
  (1) Tail Servo BLS905/MS525 or Savox 1290mg

Whiplash Clutch Liner (Pack of 2)

Miniature Aircraft Whiplash Tail Boom (131-62) - Pack of 2

Miniature aircraft Whiplash-G II Gasser version combo

Including

• Miniature aircraft Whiplash-G II Gasser Kit  MA1033-3
• 4  servos : 3x Savox 1257/8+ 1 x 1290 tail or KST (stock pending)
• Zenoah Modified  Engine 240 (Balanced wheel , matched Piston, for reduced Vibrations). special made for Whiplash Gasser
  - Option 1 :Zenoah Modified Engine 270 (Balanced wheel , matched Piston, for reduced Vibrations) special made for Whiplash Gasser
  - Option 2 :Zenoah  Hanson 3D 290 modified special made for Whiplash Gasser
• Main Carbon 710 mm blades, and tail Carbon blades 105mm
• Original MA4000 Gasser Muffler

Miniature aircraft Whiplash-N II Nitro V2 - Kit version, no blades or electronics/motors included

Chassis:

•     Sturdy graphite main frame unit.
•     All C/F parts are made from 100% carbon.
•     CNC machined Delrin 117 tooth helical main gear
•     High quality one way bearing Made in Germany
•     High quality one way bearing hub, full ball bearings
•     Heavy duty, high quality front tail drive gears Made in Germany
•     High precise two-piece clutch bell with double ball bearing support
•     Optional gear ratios
•     True T6-6061 CNC machined aluminum components
•     CNC machined aluminum triple main shaft bearing blocks
•     Direct controlled 120 (degree) CCPM
•     CNC machined aluminum boom clamps
•     CNC machined aluminum engine mount
•     Full ball bearings throughout
•     High quality landing gear struts

Rotor Head:

•     Full ball bearings
•     Heavy duty linkages
•     9mm head axle made from special high quality steel
•     CNC machined aluminum swashplate
•     CNC machined main rotor grips
•     CNC machined main rotor head
•     High quality swashplate heim ball/ball bearing by original SKF
•     High precise swash plate follower arms with 4 ball bearings each

Tail Rotor:

•     Full ball/thrust bearings
•     Tail Rotor hub made from special high quality steel
•     Graphite tail fin
•     CNC aluminum “open” gearbox
•     CNC machined tail gears made from aluminum and POM
•     Aluminum 22mm tail boom
•     Positive control system
•     Hardened tail rotor output shaft
•     High precise tail slider
•     Carbon/Aluminum boom supports

Canopy:

•     High Visibility Painted Epoxy-Glass Canopy

Specifications

• Heli Length :    52.5" (1333mm)
• Heli Height :   17.5" (445mm), Flybarless - 17" (432mm)
• Rotor Span : 1561-1601mm - 690-710mm blades
• Tail Rotor Span: 286mm with 105mm T/R blades
• Avg. Ready-to-Fly Weight: 10-11lbs - 4.5-5kg (less fuel)
• Main Drive Ratio : 8.35 : 1 7.8 : 1 (optional) 7.3 : 1 (optional)
• Tail Drive Ratio : 4.66:1
• Main Rotor Blades : 690-710mm
• Recommended Power : .90 to 120 size glow

Whiplash Pitch/Ail Servo Rail (Pack of 1)

Plastic Ball Link - M2 x 21.2 for whiplash gasser - Pack of 10

0869 Plastic Washout Links for whiplash models - Pack of 2

Special Sprague Bearing for Whiplash repair work only- Made in Germany

Swashplate Follower Assembly

Tank Plate Mounting Studs (Pack of 2)

m2.6 x 86 Threaded Control Rod - Pack of 2

Thrust Bearing 9 x 17 (Pack of 1)