Flybarless controllers

replaced by new item- click here to go to the replacing item  BX76404

Required to connect the brushless RPM sensor to use the speed controller function* in MICROBEAST PLUS and MICROBEAST PLUS HD

Suitable for brushless RPM sensor, universal ( BXA76013 )

Included:

1 x adapter cable

* Microbeast Plus HD not included!

* A paid firmware update is required for operation.

BEASTX Receiver Adapter Cable 8cm-BX76002

Set of long receiver wiring leads for the MICROBEAST flybarless system.

Length of 15cm and intended to be used to connect the MICROBEAST to your receiver.

Package includes:

• 3 multi conductor receiver leads, each 15cm in length.

This is a Do-it-yourself sensor kit to replace any needed Magnetic sensor.
the kit comes with clear instruction how to solder the wires, and place it best way, you may also print your 3D mount if needed, or use any PCB isolating material to make it yourself.

Kit including wire connector 30cm, sensor and heatshrink set.

MICROBEAST Special adhesive foam tape, 4 pcs in pack

MICROBEAST Tail Gyro Adapter Cable

Mikado Current/Voltage/Capacitysensor for VBar Control

Hardware Features of the Current/Voltage/Capacity Sensor for flight packs:

• Individually precision calibrated
• Optocoupler
• Reverse battery protection
• No influence from motor or current carrying wires

Software Features:

• Direct displaying from voltage and capacity
• Max. current and min. voltage storage
• Logfile data from the flight
• Battery Logbook with names
• Adjustable capacity, residual capacity and voltage for each battery
• Residual capacity is shown as bar in the radio display
• Overdischarge Warning
• Warning at use of not fully charged batteries
• Loud speaker announcement for reducing battery capacity

Notes:
Requires a VBar with Spektrum Satellite connectors (telemetry bus for VBar Control)
Not suitable for measuring receiver packs only (e.g. on a nitro heli)
extracted capacities are not added up, measurement only on a per-flight basis

Specifications:

• Current Consumption     2.5 mA
• Working Temperature Range     -5 to 50 °C, 23 to 122 °F
• Dimensions     approx. 20 x 20 x 10 mm
• Power Rating     120 A continuous, 330 A peak
• Effective Range (current)     0.1 A to 300 A
• Effective Range (voltage)     5 V to 100 V (2s to 16s LiPo)
• Resolution     0.01 A / 0.01 V

Contents:
Device   Voltage/Current Sensor with connecting wires to battery and ESC
Connecting Wire     Sensor wire 500 mm

Accessories:

• Connecting Wire 250 mm     04898
• Connecting Wire 500 mm     04899
• Battery ID Reader     04907
• Battery ID Tags (10 pc.) 04908
• Miscellaneous

Mikado Protection Case for NEO Aluminum case, black color #05270

For devices of the 2nd Generation (V2) only.

Mikado Protection Case for NEO Aluminum case, gold color

For devices of the 2nd Generation (V2) only.

Mikado Protection Case for NEO Aluminum case, Silver color #05549

For devices of the 2nd Generation (V2) only.

Case for VBar NEO  For the 2nd hardware generation
04945/46 VBar NEO 6.1 Express (with antenna connectors on the main board)
04949/50 VBar NEO 6.1 Express NEO VLink (with antenna wires plugged in directly to the single pc board)
05054 VBar NEO VBasic

This is a replacement antenna for Mikado Vbar Antenna for VBar NEO, 180mm #05063

SPARTAN Gyro Metal plate
Gyros are sensitive to high frequency vibrations. The metal plate helps isolate these vibrations and not allow these vibrations to be transmitted to the Gyro. If your gyro was working fine and then suddenly started to drift try to find the source of this possible vibration.

We recommend to use the metal plate between the gyro pads.

1 metal plate in a set

SPARTAN Vortex VX1 Wire Set

This pack includes a complete set of wires for connecting the Vortex to a standard receiver.
The heavy gauge male-male wire can also be used for PPM or SBUS connections.
This is the same set of wires supplied with the Vortex VX1 flybarless system.
Servo-Servo wire length 90mm.
Servo-Sat wire length 100mm.

Suitable for: Vortex VX1, Vortex VX1n

SPARTAN Vortex VX1n Wire Set

This pack includes a complete set of wires for connecting the Vortex to a standard receiver.
The heavy gauge male-male wire can also be used for PPM or SBUS connections.
This is the same set of wires supplied with the Vortex VX1n flybarless system.
Servo-Servo wire length 145mm.
Servo-Sat wire length 210mm.

Suitable for: Vortex VX1, Vortex VX1n