eRCmarket

Electric retracts remove all the hassle normally associated with air retract plumbing or getting a mechanical linkage to fit exactly. The retract set includes two retract units that are designed to accept 10mm wire legs and is suitable for models with a maximum weight of 20kg.

These retracts can be used in both electric and engine powered models. They are designed to primarily use the power supplied through the receiver. This can come from the battery in the case of engine models, or a BEC system in electric models. If you use heavier wheels/legs or have lots of drag on the leg doors, then current consumption is increased. If you have any doubt of the power available then you can use a separate battery supply for the retracts using one of the special 'Y' leads.

Each unit has built-in over-current protection. If the leg is stopped in any way during movement, or the load is too high to protect the retract from damaging or drawing too much current.

Specifications:

• Leg Wire: 10mm
• Max Weight: 20Kg
• MountPlate: 43 x 51
• Stall Current: 2.1 to 3A
• Weight: 186g
• Voltage: 4.8 - 7.4v
• Dimensions: 92 x51 x 31
• Gear Type: Metal
• Torque: 15.50 kg/cm-4.8v
• Torque: 20.60 kg/cm-7.4v
• Speed: 6.00 secs-4.8v
• Speed: 4.00 secs-7.4v
• Type: Digital

This electric retract range is designed to keep retract installations simple and reliable with great value for money. The electric retracts remove all the hassle normally associated with air retract plumbing or getting a mechanical linkage to fit exactly. The retract set includes two retract units that have pre-installed 5mm diameter studs for use with oleo legs and is suitable for models with a maximum weight of 10kg.

These retracts can be used in both electric and engine powered models. They are designed to primarily use the power supplied through the receiver. This can come from the battery in the case of engine models, or a BEC system in electric models. If you use heavier wheels/legs or have lots of drag on the leg doors, then current consumption is increased. If you have any doubt of the power available then you can use a separate battery supply for the retracts using one of the special 'Y' leads.

Each unit has built-in over-current protection. If the leg is stopped in any way during movement, or the load is too high to protect the retract from damaging or drawing too much current.

Specifications:

Leg Wire: 5mm
Max Weight: 10Kg
MountPlate: 44 x 51
Stall Current: 2.1 to 3A
Weight: 92g
Voltage: 4.8 - 7.4v
Dimensions: 92 x51 x 31
Gear Type: metal
Torque: 15.50 kg/cm-4.8v
Torque: 20.60 kg/cm-7.4v
Speed: 6.00 secs-4.8v
Speed: 4.00 secs-7.0v
Type: digital

This electric retract range is designed to keep retract installations simple and reliable with great value for money. The electric retracts remove all the hassle normally associated with air retract plumbing or getting a mechanical linkage to fit exactly.

These retracts can be used in both electric and engine powered models. They are designed to primarily use the power supplied through the receiver. This can come from the battery in the case of engine models, or a BEC system in electric models. If you use heavier wheels/legs or have lots of drag on the leg doors, then current consumption is increased. If you have any doubt of the power available then you can use a separate battery supply for the retracts using one of the special 'Y' leads.

Each unit has built-in over-current protection. If the leg is stopped in any way during movement, or the load is too high to protect the retract from damaging or drawing too much current.

Specifications:

Leg Wire: 5mm
Max Weight of model 6kg
Mount Plate: 74x44x28 mm
Stall Current: 2.1 to 3A
Weight: 69g each side
Voltage: 5-6v
Gear Type: metal

This electric retract range is designed to keep retract installations simple and reliable with great value for money. The electric retracts remove all the hassle normally associated with air retract plumbing or getting a mechanical linkage to fit exactly.

Each unit has built-in over-current protection. If the leg is stopped in any way during movement, or the load is too high to protect the retract from damaging or drawing too much current.

New electronic scales, wider selection of capacities & resolutions, have been included in a low-profile rugged housing . Those scales are Small size, and great for Hobby purposes.

Specifications
Counting Mode: 2000 gr
Precision: 0.1gr

EMax BLHeli Series 12A ESC for Multicopters (ONESHOT Available) .Based on BLHeli firmware, further optimized to the perfect drive performance. Low-voltage protection, over-heat protection and throttle signal loss protection. Separate power supply for MCU and BEC, enhancing the ESC’s ability of eliminating magnetic interference.

Parameters of the ESC can be set via program card or transmitter.
Throttle range can be set to be compatible with different receivers.
Equipped with built-in linear BEC or switch BEC.
Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.

Emax 12a ESC SimonK Series Speed Controller Perfect for the 250 and 300 Size Fpv Racers. Superb esc that provides lightning fast throttle response which is ideally suited to the FPV Racing Quadcopters. The perfect ESC for your 250 quad race project.

 

Set of screws , all you need to have for repairing an Eolo/ Spirit heli. Purchase this set and you save more then 50% of cost. Included in the package

QTY
S0030 M3x8 caphead x10
S4354 M2.5x6 caphead x10
S0079 M3x5 caphead x10
S0041 M3x3 grubscrew x 20
S3370 M2.5x8 caphead x10
S0116 M2.5x10 caphead x10
S0029 M2x8 caphead x10
S0114 M2x12 caphead x 10
S0039 M3x10 caphead x 10
S0100 M2.5x4 caphead x10
S0117 M2x5 caphead x10
S0080 M2x10 caphead x10
S4141 M3x6 caphead x10
S0074 M2x14 caphead x10
S4300 M2x6 caphead x10

eRCMarket High Quality Polo T-Shirt.

Available sizes: M, L and XL

Color: Black

eRCMarket High Quality Sweater with no Zipper, those sweaters made in UK and offer excellent textile quality for years.

Available sizes: M / L

Color: Black

The advantage of this sleeve is the high protection for electronics, silicone wires, etc. This product has excellent resistance to temperature , oils, carbon and sharp corners of frames, which can defect the wires and cause real trouble to the model.

Always use this as an extra insurance in your model. 80 % of crashes caused by electronic issues caused by cables shortcut or exposed. this is the right material to save your heli, to be more precise- to prevent those issues.
Many pilots using spiral wrap= this is Not good, it cuts the wires. this sleeve will protect them.

Don't compromise. Proven to save many cases of Model crash/Loss , Good chemical resistance Superior strength and abrasion resistance

to be used on Servo wires, Battery cables, fuel lines, and just every thing you want to protect.

Maximum continuous operating temperature from -80°C - 200°C (melting 250C)

Available Sizes guide:

-  For 1 Servo wire ,Choose the "2-7"mm (Blue or Black)

-  For 2-4 Servo wires, or silicone cables 1.5-6mm, Choose the "3-9"mm (Black)

-  For 3-6 servo wires, or Multiple Silicone cables 2-6 mm, or fuel line, Choose the 8-13mm (Black)

Available in Black or Blue color( depends on size) .

Pack of 1m

Extension Wire twisted /flat 18AWG, 1.2mm², used for SBUS extensions, or servo HD, or Quad's ESC & motor.

RC Extension Wire (Futaba/JR/Hitec) Servo Cable /Lead Switch Harness PVC Wire Silicone Wire
Connect two servos to a single servo port.

Specifications:

1. Conductor Wire: 30X0.20mm
2. Color: Black Red white
3. Compatible JR or Futaba

Package of 1m long

Want to make your Robbe heli extreme 3D?This kit will make your head extremely responsive,

Futtaba 10c(FF10) , 7C (FF7) Transmitter SWITCH NUTS green color

Full set including 8 pcs and Removal/installation tool. Fits Futaba 10c(FF10) , 7C (FF7)

You'll notice that the upper rim of the nut is smooth. Some Transmitters have the slots cut in the nuts had sharp corners. If you using to put the fingers between the switches, this got to be very irritating. Those nuts have smooth rim.

Fiala 3-Blades 20x10 Electro E3 woodpropeller - nature

Specification:

• Manufacturer:     Fiala
• Folding propeller
• Sheet:     3
• Color:     natur
• Prop material:     Holz
• max. Numbers of revolutions [rpm:     9936
• Slope [inch]:     10
• Diameter [inch]:     20
• Type:     Elektro E3
• Pusher Props
• Weight [g]:     0.000
• Drilling:     10
• Height [mm]:     0
• Width [mm]:     0
• Length [mm]:     0

Fiala 3-Blades 20x10 Electro E3 woodpropeller - nature/pusher (left turning)

Specification:

• Manufacturer:     Fiala
• Folding propeller
• Sheet:     3
• Color:     natur
• Prop material:     Holz
• max. Numbers of revolutions [rpm:     9936
• Slope [inch]:     10
• Diameter [inch]:     20
• Type:     Elektro E3
• Pusher Props
• Weight [g]:     0.000
• Drilling:     10
• Height [mm]:     0
• Width [mm]:     0
• Length [mm]:     0

Special with Mini pump( Primer)

The LiPo Safe sack/bag is a hi-tech bag made of space-age materials that has the ability to contain a lithium polymer battery fire or charging mishap. Place your lithium polymer battery inside the LiPo Safe and extend the charging wires through the top flap. Charge the lipo batteries when they’re in the LiPo Safe for peace of mind and greater safety. In the case of a lithium polymer battery charging mishap, the LiPo Safe’s fire-resistant material mitigates the ferocity of the LiPoly blaze inside and vents the smoke outside the LiPo Safe.

Size 23cm x 30cm - fits for 2 packs 6s 5000, however we recommend to use each pack with each bag.

The LiPo Safe is sealed with a thick, industrial strength, Velcro flap. The current LiPo Safe is designed to handle a lithium polymer battery mishap

Before using the LiPo Safe you must read and understand the LiPo Safe Safety Instructions. We assume absolutely no liability for any damages of any kind - even with proper use. When using the LiPo Safe, you must always remember to abide by safe lithium polymer battery charging and safety rules and never leave charging li-polymer batteries unattended. Never leave damaged lipos unattended. Always use the LiPo Safe on a non-flammable surface and in a ventilated area. Avoid damage to the LiPo Safe and not use the LiPo Safe if it is damaged.

Instructions to use:

Ensure that charger rate is properly set and polarity is correct

1. Attach charging leads to battery
2. Place battery in LiPo Safe towards the bottom
3. Place LiPo Safe on non-flammable surface
4. Route charge leads through vent at the top seam of the LiPo Safe
5. Close top flap of LiPo Safe and press hook and loop closure fully closed
6. Charge battery using proper charging practices
7. Always practice extreme caution when charging and never leave a charging battery unattended

Please check the Video showing the use of Lipo Safe

Flanged Bearing 2x6x3F

This is Flat futaba color pvc wire; extremely flexible high strand-count copper. This wire will stand up to repeated flexing and vibrations. We recommend this wire for most standard and medium/heavy duty applications.

Flat wire for your own extensions or prolong your servo wires.

• Size: 0.25mm/2 thickness
• Length of 1 meter
• Color: White, Red, Black
• Resistance: 19.0ohm/1000ft

Flat silicone Servo Wire JR & Futaba Red 3 x 0,25 mm² (1m)

Specifications:

• Corrosive Resistant A2 Grade Stainless Steel.
• Form A Thick Flat A2 Grade Stainless Steel Washers DIN125
• Dimensions (approx) - Inner 2.8mm, Outer 6.75mm, Thickness 0.5mm

 

Specifications:

• Corrosive Resistant A2 Grade Stainless Steel.
• Form A Thick Flat A2 Grade Stainless Steel Washers DIN125
• Dimensions (approx) - Inner 4.3mm, Outer 8.5mm, Thickness 0.8mm

 

Specifications:

• Corrosive Resistant A2 Grade Stainless Steel.
• Form A Thick Flat A2 Grade Stainless Steel Washers DIN125
• Dimensions (approx) - Inner 5.3mm, Outer 10mm, Thickness 1.0mm

 

Great for making your own Night flight lighted signs. Strip is 3x20cm in size.
Kit comes with 6-12 volt driver . Best is to connect with Small lipo 2-3 cells, or attach to Balance port of large lipo and use 2-3s from this source.
You can attach the sheet to  Drone, heli, or on the boom and fly in the dark.
Alternatively, Print your name, stick on the sheet and it will glow in the dark, turn on and you have a beautiful lighted sign!
 
One driver can feed up to 3 sheets.
Set include 1 Glow sheet and 1 Driver/ inverter

Color- choose yours from Blue/White/Yellow/Red

 GPS features:

•   Built‐in 15X15X4mm ceramic patch antenna on the top of module Ultra‐HighSensitivity: ‐165dBm(w/o patch antenna), up to 45dB C/N of SVs in open sky reception.
•   High Update Rate: up to 10Hz
•   12 multi‐tone active interference canceller
•   High accuracy 1‐PPS timing support for Timing Applications (10ns jitter)
•   AGPS Support for Fast TTFF (EPO™ Enable 7 days/14 days/30 days )
•   EASY™: Self‐Generated Orbit Prediction for instant positioning fix
•   AlwaysLocate™ Intelligent Algorithm (Advance Power Periodic Mode) for power saving
•   Logger function Embedded
•   Gtop Firmware Customization Services
•   Consumption current(@3.3V):
•   Acquisition: 25mA Typical
•   Tracking: 20mA Typical

Board features:

•   Dimensions 26 mm x 40 mm
•   Power supply: 3.3V at 5v
•   3V coin cell CR1220 holder (Coin cell included)
•   115200 Baud & 10 Hz firmware uploaded

Flybar conus weight and stiffener.
Those conical  adapters must be fitted on any Helicopter to balance the flybar.
The conus creates good and equal Load Sharing on the Flybar Area and will prevent the flybar to weaken and break as a result of vibrations.This is a "Must" part for any Helicopter.
Fit 4mm flybars , made from  7075 Alu , set of 2 pieces.

Made from precision ground steel for excellent strength and corrosion resistance. Those flybars can help to improve hover stability for novice flyers and more 3D response for expert flyers.

Pack of 1 piece, 4mm diameter, 52cm long. Black color

Single piece Flybar weights. Fit all models with 3mm flybars.

Weight per pcs.: 7gr
Diameter inside: 3mm
This kit includes 2 pcs. inclouding set screws

Flybarless combo to convert/upgrade a 600 size helicopter to flybarless.

Combo contains :

•   Complete Agile 5.5 Flybarless Head 600 size, shaft 10mm
•   Micro beast-X Flybarless unit

We are happy to offer you Heli or Multirotor flying lessons with professional helicopter pilots.

The lesson can be done with your own helicopter or with Pilot machine.

Should I use my machine or the Pilot's?

If you use your own Helicopter / Drone, you get familiar with the feeling and sometimes it's easier and better.

But if you want to try flying before buy, its also good to take lessons with Pilots machine.

Flying lesson is done by appointment with the pilot.

The time is 1 hour and usually it will be started by Theory explanation And followed by Flying.

Please contact us for more details.

Screen: 2" TFT LCD display.
Resolution: 960*240
Brightness: 450 cd/m2
Contrast: 500:1
Antenna: included
Channel: single way 5.8G input, 4 frenquency ranges 32 channel optional.
Battery: 500mA lithium battery, charging time 90m usage time about 100m.
Power loss: 320 mA 3.7V (Max)
Working enviroment: -10~+65 C Degree
Antenna: Built-in 3dbi brass 5.8G antenna
Power button: boot or shutdown
CH button: Long Press to adjust frequency ABEF ; Short Press to adjust frequency 12345678
Battery: Built-in 500mA lithium battery
Charge indicator: red light when charging, red light off when the battery is fully charged
Channel indicator: indicates the current receiving frequency, such as: E1, corresponding to the red lights of E and 1 will on.
Charging port: micro USB + 5V (use only rechargeable)
Charging current: 500mA
Charging time about 90 minutes
Time about 100 minutes

Package included:
1 X Watch
1 X USB Cable

1 X User Manual

This is a 1/4 Inch CMOS 700 TVL color board camera, mini size, low power consumption.
Perfect for Any FPV and Video use.

Features:

• Sensor: 1/4 CMOS, 700TVL
• Lenses: 3.6mm
• Input :12V
• Output: Wire/BNC
• Mini size: 32X32 or 38X38 customised

• Sensor: 1/4 CMOS
• System: PAL
• Effective Resolution:(H)×576(V)
• Illumination :0.2 LUX / F1.2
• Resolution:700TVL
• Scanning Frequency:50Hz -60Hz
• Gama:0.45
• Electronic Shutter :1/50～1/100000s
• S/N >46dB
• Video Output  1.0V p-p
• Operation Temperature : -20 C to 50 C

Frames posts set R30-50

Transparent fuel filter, Perfect for all Nitro engines, easy to disassemble, clean and maintain. comes with fuel line holder, and Filter holder.

Easy to attach to any model

1 filter SET in pack

Fuel Stopper set