eRCmarket

High quality and good looking CNC transmitter stand that should work with any radios that has a round handle with a diameter of 5mm and length of 85mm.

Avaliable in Light Blue color (Transmitter not included)
Please see Zoom images to see how Transmitter looks with the stand on it

3.5mm gold Connectors for connecting to your battery, speed control, charger, power meter or similar applications!!

These have low resistance, and gives the best electric flow.

• Diameter: 3.5mm
• Current: 80Amp Max
  
• Weight: 2.19gr/set

Included:

•  2 x Red Casing
  
•  2 x Male 3.5mm Gold Bullet
•  2 x Female 3.5mm Gold Bullet

Anodized fuel T-couplers. fit standard fuel line, Suatable for Nitro and Gasoline
Silver color, set of 2

Special Antenna Tubing, length of Approx 1m, to install antenna on your heli or Airplane/car

Receiver Wire, direct replacement for broken Rx aerial.length of 1meter, color - Black

Replacement spacer - cnc Metal

Against electro-static charge. A must for Helicopters
Surface-active product preventing accumulation of static electricity on various surfaces. Leaves ultra-thin invisable anti-static film.
ESD-protection.
Spray- 200 ml

ArduPilot APM 2.8 Mega External Compass APM Flight Controller Combo w/Ublox NEO-6H GPS for Multicopter

Package content:

• ArduPilot Mega 2.8 Fully Assembled with plastic case x 1
• UBLOX NEO-6M & MAG GPS module x 1
• Accessories (see picture)

Introduction:

This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the  uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.
The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

Features:

• Arduino Compatible
• Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
• Onboard 4 MegaByte Dataflash chip for automatic datalogging
• Optional off-board GPS, uBlox LEA-6H module with Compass.
• One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.
• Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties
• Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

GPS Features:

• Built-in compass GPS module
• Main chip: uBlox LEA-6H
• With Flash and temperature compensation
• With fast satellite searching speed and high precision
• Compatible with APM serial port and I2C port
• Includes round plastic shell and GPS support

Avatar 360 Airbrush Fiberglass Canopy (Red)

Avatar 360 Tail Boom arm CF

Avatar 360/450 Landing gear mount

Avatar 360/450 Motor Mount red

Avatar 360/450 outside-boom 16mm

Avatar 360/450 T holder 16-12

Avatar 450 Airbrush Fiberglass Canopy (Red)

Axle Set Hubsan

Blue or neon red colors, set of 10

This tiny tool is designed to help you screw push-rods into ball-links.

It can either be used in the chuck of an electric drill, in the telescopic handle, or in a 5.5 mm socket.

Ball-link driver for 4 mm telescopic handle.

This jack easily mounts and contains a solder point for connection. 4mm opening to accept banana plugs.
Set of 2 (Black and Red)

4mm Banana Jack (Gold plated) set, fits all Chargers..

Set of  Red & Black or Blue & Yellow

Excellent quality connectors, made in Germany

The cable made from Silicone 2 x0.50mm .Fits Futaba or Jr ( per choice) .

This cable is produced and tested with most modern procedures. Cables are tested individually at 48v test, Conduction test, Polarity and shortcut test, stability of the contacts.
Those cables provided with 3 years Guarantee.

Specially made for Robbe helicopters, This is set needed to replace all possible bearings.
Cost economic (50+% less then if purchased separately)

Included
S4035 (3x8x3) x 8
S4303 (5x13x4) x 2
S0211 (10x22x6) x 2
S0212 (8x16x5) x 2
S3367 (4X10X4) x 4
S1551( TRUST) X 2
S4287 (8X19) X 2
S3364( TRUST) X 2
S4299( 7X14) X 2

Aluminium bellcrank conversion set for all versions of the , Cuatro, Dyna-x,Futura and the Millennium, and gives your helicopter an improved appearance as well as a more direct swashplate linkage.
Contains- 4 alu bellcranks+ metal balls,

Ball bearings and washers can be reused from the plastic set.
Optional  8 bearings (3x8x3) + shims can be purchased

12.9 grace black high tensile steel as standard with a high tensile steel, they are a perfect addition for environments where corrosion won't be an issue.
High-quality threaded design, ensuring the screws turn effortlessly into the socket

Size M4x10, pack of 10

12.9 grace black high tensile steel as standard with a high tensile steel, they are a perfect addition for environments where corrosion won't be an issue.
High-quality threaded design, ensuring the screws turn effortlessly into the socket
Size M4x8, pack of 10

Blade 3x8x3.5 Thrust Bearing (2pcs)

• Beam angle: 180°
• Power consumption： 1W
• Voltage： DC12V
• Lumens: 70-80LM
• Size: 25 (dia) x 15 (H) x 15mm (total lenght)

• Aluminum cooler

• Beam angle: 80°
• Power consumption: 0.7W
• Voltage：DC 12V
• Lumens: 55-65LM
• Size: 25x11mm

• Aluminum cage
  

Brushless Motor Mount : Out-runner

This range of A2 Stainless Steel Button Head Socket Screws are manufactured to ISO 7380. They are sometimes also known as allen screws. Being made from A2 Stainless Steel means they are ideal for use in external or damp environments such as food factories, engineering, toolmaking, automotive, furniture production etc.

Button Head socket screws are easily tightened using a hexagon wrench key and have a neat dome headed appearance.
They are measured form under the head for the length and are not supplied with nuts as standard.

Size M4x8
pack of 10

Carbon Landing gear Hardware- Now its possible to have those parts as a separate set.
Set of 4 connectors with necessary hardware, Inox made, fit Landing gear Skids with diameter of 10mm.

Carbon fiber rod diameter 1.5 mm,80-90 cm long.

Carbon fiber rod diameter 1mm, 80-90 cm long.

Carbon fiber rod diameter 2mm x100cm long.