eRCmarket

Multicopter 4 Propeller set 11x4.7 ( Pusher and Tractor) , Set of 2L+2R.
These are very nice multicopter propellers that are quite stiff in comparison to similar props of ABS plastic construction. There is definite resilience to breakage combined with solid flying performance from these propellers

COMMENTS: For Electric flight only. Do not modify or attempt to use with Glow engines.
 

Multicopter 4 Propeller set 8x4.3 ( Pusher and Tractor) , Set of 2L+2R.
These are very nice multicopter propellers that are quite stiff in comparison to similar props of ABS plastic construction. There is definite resilience to breakage combined with solid flying performance from these propellers

COMMENTS: For Electric flight only. Do not modify or attempt to use with Glow engines.

1 Pair 8X4.5 Carbon Fiber Propellers CW/CCW for multicopter

Specifications:

•   Material:Japan made carbon fiber
•   Epoxy resin cover
•   Size:8x4.5
•   High gloss 3K finish
•   Very strong and light weight

Included 1 CW, 1 CCW

5V-12V Adjustable Voltage BEC Output ESC Distribution Connection Board

This board is designed with dual channel BEC output distribution, with turmeric processing in surface, can support max. 100A current. The high effeciency dual channel BEC circuit structure can support 6S Lipo battery input. One channel is 12V output, while another channel is adjustable, support 3-12V. Each BEC supports 2A stable output (can also reach 3A stable output with another heat sink)!

What are you waiting for? 12V BEC + 5V BEC + ESC distribution board, wherein the 12V BEC can directly offer power to brushless gimbal, 5.8G graphic transmission or FPV cameras and 5V BEC can offer power to open source brushless controller and Gopro, etc.

*Note: Before use the BEC output, please measure the real output voltage to make sure it meets your requirment. The default BEC output is 5V.

Max current:up to 100A
Standard 50mm * 50mm board size
Weight : 9gr

40 AMPS esc , specially fit Multicopters, best to be loaded with SimonK soft

Extremely low internal resistance
Super smooth and accurate throttle linearity
Safety thermal over-load protection
Auto throttle shut down in signal loss situation
Supports high RPM motors
Power arming protection (prevents the motor from accidentally running when switched on)
New advanced programming software

• Output: Continuous 40A, Burst 60A up to 10 Secs.
• Input Voltage: 2-6 cells lithium
• BEC: 4A/5.5V
• Dimension (mm) W*L*H: 23 x 52x 7
• Weight: 32g

NAV Module x 1

UART 4Pin cable (to GPS) 200mm x1

I2C 4Pin cable (to FC) 100mm x1

Features:

All GPS data available via the I2C bus to connect to 328P Multiwii FC

A LED on board show GPS 3D Fix status

ATMega 328P Microcontroller

2 Molex 1.25mm 4Pin socket for GPS receiver and FC

2 port for ISP and FTDI

Specification:

Dimension: 20mmX30mm

Height: 5mm

Weight:2.4g/5g(include cable)

Hole diameter: 3mm

Prop Guard for the Nano Flip Quadcopter

The Acro Naze32 is one of the best flight controllers available for Multi-rotors.this board is Acro version and not including the Magnetometer and barometer

This FC features an STM32 32-bit processor and comes in an acro version and and full version. The Naze 32 can be used in many different configurations (up to an octocopter).  It also does FrSky Telemetry, Multiwii serial protocol, and can control a camera gimbal control.

MCU:ST Microelectronics STM32F103 72-MHz ARM Cortex-M3
Motion/Position Sensor:Invensense MPU6050 6-DOF MEMS Sensor (3-axis Gyro + 3-axis Accelerometer)
Compass:none
Altitude Sensor:none
Dimensions:36mm x 36mm
Hole Spacing:30.5mm x 30.5mm
Weight (bare):6 grams
Weight (with pin headers):8 grams

Note that returns on these are not accepted after soldering. Please plug the board into your computer BEFORE you solder it to check it works. 

Set of needle levers for ALL engines such as OS engines .With those levers it will be easier to adjust the engines by remembering visual position

Set comes with 2 levers and screws supplied.

Color: Silver-Blue

The neXt level of heli simming. We gave our rc Helicopter Flight Simulator the name neXt because it heralds the next evolution in the model flight simulator industry.

THIS IS a download product, and you will receive a license details once payment completed.

the simulator delivered always as  Latest version. No return possible on such product.

The neXt level

of radio control flight simulation. We gave our RC Flight Simulator the name neXt because it heralds the next evolution in the model flight simulator industry.

Videos

To demonstrate the quality of the physics simulation we have published a few videos here.

Thanks to the highly effective programming beneath the hood of the graphics engine, you'll get the highest quality not only on the latest hardware, but also smooth performance on older computer systems.

System

Windows
Apple Mac OSX
Ubuntu Linux

All input devices that output a joystick signal will be accepted: compatibility list.

Content

The simulator contains 26 flight sceneries, 98 helicopters, 15 multicopters and 25 fixed-wing models. More scenes, models and functions will be added in updates. All 2.x updates are free of charge.

Beginner

The hover flight trainer progressively enables more and more control functions in order to help beginners learn hovering from the four predefined angles. An inverted-flight trainer completes this training program. The switchable autopilot simulates the flight behavior of real helicopters with rescue systems (e.g. BEASTX Microbeast Pro-Edition).

Night Fly

with fire and a spot light. Inspired by Camp Hardcore and Tony Whiteside. The only place in USA to allow spot light flying.

Racetracks

for multicopters and fpv camera including a top 30 highscore list (offline and online).

Advanced

The Simulator is of course fully 3D. If necessary, the neXt shows the stick movements with four available control assignments. Now you can train blade scratching. Practice autorotations and learn the required pitch inputs to perform the manoeuvre in reality with confidence. The more the energy builds up in the main rotor blades, the more the flight data display (below heli) turns yellow.

Training videos

for learning Roll, Turn, Funnel, TicTocs, Piro Flip, Piro Looping, Piro Circle, Piro TicToc, a.s.o. Press the key 'v' to open the flight recorder. Click on 'Menu' and load the desired training video.

VR

First flight sim with support for Oculus Rift, HTC Vive and Windows Mixed Reality Headsets (Open VR / Virtual Reality).

Fun

Try to land your helicopter at a box. A optional marker shows the position of the helicopter on the ground. The real time flight data display (below model) shows the selected flight data. Meet your friends online in flight meetings. A maximum of up to 16 pilots can attend a room. Record your best flights and save them to disk.

Professional film production

Practice camera flights in co-operation between the pilot and the cameraman with the DJI S1000 - including 3axis control and GPS stabilization. The camera can be controlled by a second transmitter or Joypad (Society of Aerial Cinematography / SOAC).

This Package is all you need to fly. neXt - CGM rc Heli Simulator set with RX2SIM and Sky hero AT9 tx

Simulator is Always Latest version, since the download is from the main server, and always updated version

PACKAGE including the following:

• Next simulator download (no dvd)
  
• Simulator Dongle with Cables ( Fits different radios including AT9)
• AT9 Arctic White
• No return of product possible!

The neXt level

of radio control flight simulation. We gave our RC Flight Simulator the name neXt because it heralds the next evolution in the model flight simulator industry.

Videos

To demonstrate the quality of the physics simulation we have published a few videos here.

Thanks to the highly effective programming beneath the hood of the graphics engine, you'll get the highest quality not only on the latest hardware, but also smooth performance on older computer systems.

System

Windows
Apple Mac OSX
Ubuntu Linux

All input devices that output a joystick signal will be accepted: compatibility list.

Content

The simulator contains 26 flight sceneries, 98 helicopters, 15 multicopters and 25 fixed-wing models. More scenes, models and functions will be added in updates. All 2.x updates are free of charge

Beginner

The hover flight trainer progressively enables more and more control functions in order to help beginners learn hovering from the four predefined angles. An inverted-flight trainer completes this training program. The switchable autopilot simulates the flight behavior of real helicopters with rescue systems (e.g. BEASTX Microbeast Pro-Edition).

Night Fly

with fire and a spot light. Inspired by Camp Hardcore and Tony Whiteside. The only place in USA to allow spot light flying.

Racetracks

for multicopters and fpv camera including a top 30 highscore list (offline and online).

Advanced

The Simulator is of course fully 3D. If necessary, the neXt shows the stick movements with four available control assignments. Now you can train blade scratching. Practice autorotations and learn the required pitch inputs to perform the manoeuvre in reality with confidence. The more the energy builds up in the main rotor blades, the more the flight data display (below heli) turns yellow.

Training videos

for learning Roll, Turn, Funnel, TicTocs, Piro Flip, Piro Looping, Piro Circle, Piro TicToc, a.s.o. Press the key 'v' to open the flight recorder. Click on 'Menu' and load the desired training video.

VR

First flight sim with support for Oculus Rift, HTC Vive and Windows Mixed Reality Headsets (Open VR / Virtual Reality).

This Package is all you need to fly. you can use the AT9 later for all your models, just receiver needed (Optional)

PACKAGE including the following:

• Next simulator download keys.You always get the latest version! 
• Simulator Dongle with Cables ( Fits different radios including AT9)
• AT9 Arctic White
• ( no return possible on such product)
  

The neXt level

of radio control flight simulation. We gave our RC Flight Simulator the name neXt because it heralds the next evolution in the model flight simulator industry.

Videos

To demonstrate the quality of the physics simulation we have published a few videos here.

Content

The simulator contains 26 flight sceneries, 98 helicopters, 15 multicopters and 25 fixed-wing models. More scenes, models and functions will be added in updates. All 2.x updates are free of charge.

Copy protection

The online activation requires an internet connection. A person can activate neXt on up to two computers. However, the two installations can not be used simultaneously. It violates our software terms of use when two people share a license.

Beginner

The hover flight trainer progressively enables more and more control functions in order to help beginners learn hovering from the four predefined angles. An inverted-flight trainer completes this training program. The switchable autopilot simulates the flight behavior of real helicopters with rescue systems (e.g. BEASTX Microbeast Pro-Edition).

Night Fly

with fire and a spot light. Inspired by Camp Hardcore and Tony Whiteside. The only place in USA to allow spot light flying.

Racetracks

for multicopters and fpv camera including a top 30 highscore list (offline and online).

Advanced

The Simulator is of course fully 3D. If necessary, the neXt shows the stick movements with four available control assignments. Now you can train blade scratching. Practice autorotations and learn the required pitch inputs to perform the manoeuvre in reality with confidence. The more the energy builds up in the main rotor blades, the more the flight data display (below heli) turns yellow.

Training videos

for learning Roll, Turn, Funnel, TicTocs, Piro Flip, Piro Looping, Piro Circle, Piro TicToc, a.s.o. Press the key 'v' to open the flight recorder. Click on 'Menu' and load the desired training video.

VR

First flight sim with support for Oculus Rift, HTC Vive and Windows Mixed Reality Headsets (Open VR / Virtual Reality).

Fun

Try to land your helicopter at a box. A optional marker shows the position of the helicopter on the ground. The real time flight data display (below model) shows the selected flight data. Meet your friends online in flight meetings. A maximum of up to 16 pilots can attend a room. Record your best flights and save them to disk.

Professional film production

Practice camera flights in co-operation between the pilot and the cameraman with the DJI S1000 - including 3axis control and GPS stabilization. The camera can be controlled by a second transmitter or Joypad (Society of Aerial Cinematography / SOAC).

Great for making your own lighted signs. Sheet comes as Square of 10x10cm
Kit comes with 6-12 volt driver . Best is to connect  Small lipo of 2-3 cells, or attach to Balance port of larger lipo and use 2-3s from this source.
You can attach the sheet to a Drone, heli, or on the boom and fly in the dark.
Alternatively, Print your name, stick on the sheet and it will glow in the dark,  turn on and you have a beautiful lighted sign!

One driver can feed up to 3 sheets.
Set include 1 Glow sheet 10x10cm and one Driver

different colors available: Yellow, Red, White

Great for making your own lighted signs. Sheet comes in round shape of D8 cm
Kit comes with 6-12 volt driver . Best is to connect  Small lipo of 2-3 cells, or attach to Balance port of larger lipo and use 2-3s from this source.
You can attach the sheet to a Drone, heli, or on the boom and fly in the dark.
Alternatively, Print your name, stick on the sheet and it will glow in the dark,  turn on and you have a beautiful lighted sign!

One driver can feed up to 3 sheets.
Set include 1 Glow sheet 8CM round and one Driver

different colors available: Yellow, Red, White

Complete set includes two (2) Hi-Lum contrasting glow wires of 1 meter long, and Double glow wire Driver.
All connectors are pre installed , just add your small lipo 2s 300-1000mh

That all you need, and it's ready to fly.
The dual controllers increase brightness significantly.

High-intensity light wire that glows strong at night.

The driver ( a tiny black box ) can power up to three light wires each measuring at 1-2 meter long and can run for about 4 hours on a battery, recommended to use 2-3s Lithium.
The Cool lights produces no heat and very flexible and bendable so you can wrap it over the Helicopters boom, canopy and other surfaces.
Shake proof, impact proof and very versatile each install cold wire produces no electromagnetic wave so it will not interfere with the Helicopter’s receiver signals which is very important.

Our Night Wires are especially produced for Military Night Flying, and used on many UAV's and other applications where most of reliability needed.
Those Wires are produced in Europe, and producing 25% more illumination compared to their competitors. And all this without extra consumption of power. very high efficiency

Thicknesses of 2.5mm, flexible and 1 meters Long.

You will need converter(Driver) and Battery 7.4-12v.

Driver box from 7-12v . up to 3 Night Wires can be connected to this box, providing you with the best lumination for night flying.
This driver comes with 2 connectors for wires.
Small size 27 x 28 x 27 mm and lightweight - less then 10 grams make this driver a perfect solution for Night flying.

Connect 2- 3s lipo/Li-on, or 9V battery and you have Hours of continious night flying. 80ma consumtion only.

Use this handy convenient piston stopper to lock any glow engines piston in place for safe and easy flywheel or clutch removal.

Make your work go faster with simply remove the glow plug from the engine, screw the Piston Stopper in place, and your piston and crankshaft will be locked into position.

Made from high quality aluminum this piston stopper features a knurled grip for quick finger tightening.

Plastic cap will prevent Scratching the piston.

1 LOCKER=SET

Nylon insert lock nuts are hex nuts that have a captive nylon washer mounted in their top to create a prevailing torque type lock nut. The undersized washer forms a compression grip that binds on the threads of the mating fastener to resist loosening.

Nyloc Nut (Pack of 10) M3 Nylon Insert Lock Nuts A2 Stainless Steel

 

RCEXL on board glow system, can be controlled by hand Button or remote controller, new design with heat sink
perfect for Airplanes or Helicopters and other RC glow engines to insure perfect Idle, avoid Engine cuts

• Separate design, it can be taken off under remote control mode, to reduce weight
• Compatible with car engines, with spring lock structure inside, never loose
• With 3 LED indicators, to know the working state of the drive
• Manual switch with ring type LED light for decoration
• Small size, light weight
• Wide range of voltage, input 4.5V~12.6V

This on board glow system does not have low voltage protection; please pay attention to the battery power during using. (Recommend 2S liPo battery)

CC3D Hardware Features:

• Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
• 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
• Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
• Software support for Windows, Mac and Linux.
• Direct high speed USB support with no drivers required, a truly plug and play device.
• Futaba S-BUS hardware support.
• Innovative Flexi-port technology for superior port flexibility.
• 4Mbits on-board EEPROM for configuration storage.

Flexiport:

This flightcontroller also offers an innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.
 
Superior user experience:

OpenPilot tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.
 
OpenPilot software is designed to be used by everybody! All major operating systems are supported and extra packages are also available. The software is all Free software under the GPLv3 license.

Sensors and Components:

• 3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2,
• Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, and Futaba S.Bus receivers.
• Simultaneous support for multiple receivers.
• ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
• MainPort functions (configurable): serial telemetry (default), GPS, S.Bus.
• FlexiPort (configurable): serial telemetry, GPS, or I2C peripherals (under development)
• 10 PWM outputs to servos or ESC’s, or for camera stabilization
• Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
• Onboard USB connectivity for easy configuration.
• USB and serial telemetry and configuration
• Supported by powerful OpenPilot GCS
• 4 Mbit onboard memory
• 3C Quaternion based complementary filter running at 500Hz

Package Includes:

• 1 x CC3D
• 1 x 8pc wire set
• 1 x 4pc expansion path wire set
• 1 x Damping Board
• 1 x Antenna Base

 

Special Shape carbon paddels, for Microhelicopters.Those paddles come with locking mechanism to insude they will never move on your flybar.Set of 2 Pcs

Fusuno canopies are made with highest quality resin and fiberglass material to provide strong but flexible canopies. It helps prevent cracks that is normally seen in other canopies that are using lower quality material. All paints and clear coat are automobile grade provide great look, Great design at bargain price

PANASONIC  6LR61 EVOLTA 9V

Extended Pinion to fit Millenium Helis, This pinion will make ratio 1:8 for 90 size motors
The longer sleeve is especially for double Bearing block

Pinion gear for ALU Gear box 10/12/14/16T

POWERZIP strip, 16mm wide, 1meter long

Power tape, holding power is up to 50 kg!!, Double face transparent silicone tape ( red cover), excellent for installation of wires, wood, fiber, Gyro , Receiver and more..

Its suitable for internal & external use it offers high adhesion to a wide variety of surfaces. It has superior 'wetting out' properties which increase the bonded surface area increasing the strength of the bond. It has excellent ageing properties and is resistant to U.V. light, abrasion, corrosion & moisture.
Service temperature is -30°c - +80°c (continuous)/ +130°c (shorterm).

Pack of  1 Meter long 16mm wide

 

POWERZIP strip, 16mm wide, 1meter long

Power tape, holding power is up to 50 kg!!, Double face transparent silicone tape ( red cover), excellent for installation of wires, wood, fiber, Gyro , Receiver and more..

Its suitable for internal & external use it offers high adhesion to a wide variety of surfaces. It has superior 'wetting out' properties which increase the bonded surface area increasing the strength of the bond. It has excellent ageing properties and is resistant to U.V. light, abrasion, corrosion & moisture.
Service temperature is -30°c - +80°c (continuous)/ +130°c (shorterm).

Pack of  1 Meter long 25mm wide

 

Professional Aerial dedicated HDMI adapter cable

Full compliance with HDMI 1.4 specification design, and we are fully in accordance with the design of the differential signal lines, to achieve maximum signal isolation in the design sequence distribution lines, strong anti-interference, good color reproduction.

Specification:

• Aerial dedicated
• length 18cm
• weight 5 g
• support 1920x1080p
• specification compatible HDMI1.4a

Temperature controlled solder Station , ESD-safe, with digital display of target- and actual temperature, including soldering iron with tip, iron holder and sponge in drawer.
The soldering station  is ideal for hobby, school, workshop, service and lab. The adjustment of temperature is easy with the up-/down-button in 1° and 5°C-steps. The soldering iron will be connected with a 5 poles socket to the station.
 

•   With iron holder and sponge in a drawer.
•   Compact, stable and insulated housing.
•   Station and iron holder can be placed separately.
•   Fast and easy replacement of soldering tip
•   Large LC-display with target- and actual value of temperature.
•   Temperature control with electronic sensor
•   Short heating-up time thanks to a amply designed power supply.
•   Efficient soldering iron for a wide range of application
•   Temperature range from 150 to 450°C (300-850°F)
•   Optical and acoustic error indication in case of malfunction
•   ESD-safe

Technical Specifications
 

•   Input Power: 230V (220-240V), 50Hz
•   Soldering iron power: 48W
•   Fuse: T 1A/250V
•   Temperature range: 150°C-450°C (300-850°F), in 1°C or 5°C steps
•   Display accuracy: 5%
•   LC-Display with 3 1/2 digits
•   Max. Input Power: ca. 90VA
•   Dimension WxHxL: 185x100x150mm
•   Weight: ca. 2.0kg

Contains

•   Solder station  with iron holder and drawer with sponge
•   Solder iron with tip 1,6 mm
•   Color of station plastic can vary

 

 

RCD3015G IS A full remote shutter control. Utilizing the 3 positions Switch on a standard radio control transmitter, users can now choose to take a photo or video while in flight.

RCD3015G is an enhanced version of HDMI to AV interface. Remote controlling of the camera is now possible via the 3 position switch from the radio control transmitter.
e.g. on most Futaba or JR transmitters it is possible to assign the 3 position switch to channel 7 or some spare channel.

RCD3015G senses the position of this switch and either takes a photo or records a video.

With RCD3015G the model flyer has a full control of the camera's operations while in flight. Conserving valuable storage space and battery life.
RCD3015G offers full support for SONY NEX 5N,5R,5T,6R,7N,7R

RCD3015G has been fully optimized to fit the SONY NEX series making installation a breeze

Initial Settings:

•   Set the camera HDMI output to auto resolution mode.
•   Set the video mode to infrared remote control mode.
•   Connect RCD3015G HDMI converter with the camera, connect the servo cable of shutter controlling with the remote control receiver.
•   Initialize the Camera by pressing the shutter once to get the camera out of review mode.
•   Install the optical fiber on RCD3015G converter, stick the other end of the optical fiber over the window of infrared receiver on the camera.

Important Note:

You need to have a transmitter with a 3 position switch. Map this 3 position switch to a spare channel and connect the servo cable from the RCD3015G to this channel. If there is no connection, RCD3015G works only as a HDMI to AV converter.

The control of 3-pos switch:

•   1. Up: Takes a photo (Shutter is pressed)
•   2. Middle:Shutter is off / Recording is off
•   3. Down: Video recording is on.

It is very important that the 3-position switch is set in the middle (neutral) position before you power up your RCD3015G converter. ( Note : RCD3015G powers up when you turn on the camera or power supply of reciever) When the shutter control 3-pos switch is in the middle(stop/neutral) position, the red LED is on constantly. If there is no signal from the receiver, the red LED flashes 4 times per second, it reminds customer to check if the receiver is powered and the transmitter is turned on.

Taking Photos：

Toggle the 3-POS switch from middle position to the up position, the camera will start taking photos until the 3-POS switch is toggled to the middle position. In this mode the red LED flashes 2 times per second.
Recording video:

Toggle the 3-POS switch from the middle position to down position, the camera starts recording a video till the 3-POS switch is toggled to the middle position. Video is saved in this position. In this mode, the RED LED blinks continuously.

Attention:

There must be a 5 second interval between each operation of the 3-POS switch. e.g. Switching from neutral to recording position and then back to neutral (recording stop). Please wait for 5 seconds between each mode change. The 5 second interval is required by the camera firmware. It allows the camera to clear the buffer and safely write the video file to storage. Operating the the 3-POS switch without observing the 5 second gap will cause the camera to hang and can result in corrupt video files.

RCD3015G - Input voltage must not exceed 6 volts. Do not connect a high voltage receiver to RCD3015G. The receiver power supply should be between 4.8V-6V, Operation beyond 6 Volts will result in damage the unit and potentially the camera and voids all warranties.

Compatibility list:

Full support for both of SONY 50i and 60i series.
Fully tested to work with SONY NEX-5, 5N,5R,5T,5TL,6R,7N,7R. Nikon D90,D3X.

Packing List：

• 3015G converter module  1 piece
• Black red yellow AV cable  1 piece
• 60cm long, 0.75mm PMMA optical fiber cable 1 piece (Only 15cm  is required for normal operation)

Quick, easy and inexpensive propeller balancer.

Perfect for quick, accurate balancing at home or even at the field

Fingertip Propeller Balancer 1 pc.

PROPELLER adaptor, Union type (40mm, M8 )
Fits Shafts of 5mm

Propeller Adapter aluminium shaft 3,0mm & propeller shaft 5,0mm

Weight: 7.6g

Propeller Adapter aluminium shaft 3,175mm & propeller shaft 5.0mm

Weight: 7.6g

Propeller Adapter aluminium shaft 3,175mm & propeller shaft 6,35mm

Weight: 7.6g