AVIZAR

RECEIVER Antenna 2.4ghz (2pcs) 210mm long for Futaba, Jr, Graupner

Length of 210mm for receivers FUTABA , jr, Graupner, and others using Ipex4 connector.
Also fits other brand receivers. Increasing reception.

Allows the receiver antenna to be deployed outside the fuselage in models with all-carbon canopies or fuselages
The Antenna can be replaced by any experienced user.

Set of 2 antennas

Alligator Remote glow adapter, easy connection to the glow plug. another choice of the Remote adapters

Glow plug connector , with Glow head clip at the end.

Replacement O-Ring FKM for MRCI collector 16x3.55mm, set of 2

Set of 2

Receiver Antenna 2.4Ghz 15 cm Ipex 1

Check your connector to insure its Ipex1 Type of connectors

Color can vary between Black and Gray

Receiver Antenna 2.4Ghz 15 cm Ipex 4

Check your connector to insure its Ipex4 Type of connectors

Color can vary between Black and Gray

Set of 1 antenna

• High Performance Copper Shielding sheet 
• 20x30cm
• >60db attenuation in 10MHz-3GHz
• Excellent Radiation protection
• EMF Wave Blocking (Best Value for Blocking Ability)

RGB LED Board  comes with three RGB LEDS. Seven colors are selectable by different combination of dip switches. This LED board gives an eye-catching effect to your multirotors or planes when illuminated.

Specifications:

• INPUT: 10~13V DC
• Size: 47x10mm
•      Weight: 2g
•      Packing:  LED BOARD 1pc, Double side sticker

Notes:

•     Easy to Solder
•     Be aware of the positive and negative poles, as well as the insulation;
•     Switch the related codes to ON, seven colors are selectable;
•     The input is in a range of 10~13V DC, can be powered by 3S Lipo or 12V BEC.

Selectable Colors:

    B ON =Blue, 0.35W, 0.03A
    R ON =Red, 0.35W, 0.03A
    G ON =Green, 0.35W, 0.03A
    B+R =Megenta, 0.70W, 0.06A
    B+G =Cyan, 0.70W, 0.06A
    R+G =Yellow, 0.70W, 0.06A
    B+R+G =White, 1.05W, 0.09A

RGB LED Board  comes with three RGB LEDS. Seven colors are selectable by different combination of dip switches. This LED board gives an eye-catching effect to your multirotors or planes when illuminated.

Specifications:

•      INPUT: 14~17V DC
•      Size: 47x10mm
•      Weight: 2g
•      Packing:  LED BOARD 1pc, Double side sticker

Notes:

•     Easy to Solder
•     Be aware of the positive and negative poles, as well as the insulation;
•     Switch the related codes to ON, seven colors are selectable;
•     The input is in a range of 10~13V DC, can be powered by 3S Lipo or 12V BEC.

Selectable Colors:

    B ON =Blue, 0.35W, 0.03A
    R ON =Red, 0.35W, 0.03A
    G ON =Green, 0.35W, 0.03A
    B+R =Megenta, 0.70W, 0.06A
    B+G =Cyan, 0.70W, 0.06A
    R+G =Yellow, 0.70W, 0.06A
    B+R+G =White, 1.05W, 0.09A

New! Robo-Copter Carbon Fiber Folding 750mm Version-2 FPV Quad-Copter Bind to fly set : Unfold, start and Fly
Robo-Copter 750 mm CF Folding Quad-Copter Air Frame, professionally installed, balanced, flight tested. 6s 5000 offers over 15 min of flying.

This New Air-Frame is perfect for FPV and Surveillance Work.
Strong light weight construction and unique folding design with Optional Dual axis GoPro type Brushless Gimbal.

Key Features

• Compact and modular design
• Stabilized Brushless GoPro camera gimbal 2 axis- optional
• Resistant carbon frame
• Unique folding design

Description

RoboCopter  is easy to use and fast to deploy unmanned aerial vehicle for basic aerial photography.
Using unique folding frame design with quick-release mechanism the transportation is done easy.
Custom on-board camera can be used.
Built in battery protection cage can save your battery against bad landings.

Specifications

• Operating temperature -20°C to +55°C   
• Humidity Max. 85%   
• Battery Type LiPo, 22.2 V  6s  5000- 6000mah (optional, not included by default)
• On-board camera gimbal 2 axis For GoPro 2/3/4 (optional, not included by default)   
• Flight time Up to 20 minutes   
• Max Ascent / Descent Speed 5m/s   
• Maximum payload 1.2 kg

Included: 

Professionally built and tested Quadcopter Robo frame.

• Naza V2 controller with GPS
• 4 * 40 amp  Avizar Opto ESC's, SIMONK flashed
• Motors: 4 * AVIZAR X3 6s Balanced with props
• Props: 14x5 MAH carbon propellers *4

Radio, Battery equipment as in the picture not included.

RoboCat 270 Carbon Fiber Quadcopter Combo

Robocat 270 KIT Specifications:

• Wheelbase: 270mm
• Material: Carbon fiber
• Removable hood make from shock-absorbing PC materials
• Flying weight: 410~430 (Battery excluded)
• Model net weight: 170g
• Hood color: Orange
• 1.5mm thick fuselage & 3mm thick arms

Package Included:

• RoboCat 270 Carbon Fiber Quadcopter x 1 (Not assembled)
• ESC PDB Connection Board x 1
• 2204 2300kv Brushless Motor x 4 (cw 2PCS+ccw 2PCS)
• ESC x 4
• 5" Propeller x 4
• CC3D flight controller 1set
• Radiolink AT9 radio+ receiver R6D
• Camera
• VTX
  

RoboCat 270 Carbon Fiber Quadcopter Frame Kit:

Solid frame made from super tough 4K weave carbon fiber which is supported with aircraft grade anodized aluminum frame stacks which make this frame extremely rigid and strong. The arms of the quad are CNC cut from 3mm plate while the upper, lower and center decks are cut from 1.5mm plate.

The most stunning feature is the Lexan Body shell, supplied in several colors, yellow, orange, black, green, white and clear. The clear body shell is perfect for those who are creative and wishing to customize the quad with there own color scheme's and designs. The frame is made with a unique rotating design which opens and allows easy access to the electronics without disassembling the whole frame.

The frame provides mounting positions for all of the individual components of your install including a unique FPV, SMA vertical transmitter mount. The lower deck provides plenty of space for Naze / CC3D or an equivalent flight controller along with a distribution board or breakout cable set. The FPV camera mount is per-angled which results in an optimal view for racing purposes.

The center deck is designed to cover your LiPo battery. It can easily accommodate 3-4 cell packs up to 2200mAH. The RoboCat's frame also includes a unique XT60 bracket to be sure that battery cables are protected at all times. The motor mounts of the RoboCat have 16-19mm bolt hole spacing, meaning that both 18-22 size motors can be used for this machine.

Features:

• 270 size FPV racing quad frame
• Super tough and durable all 4k weave carbon fiber construction
• Eye catching Lexan body shell design available in several colors
• Unique rotating frame design allows easy access to electronics
• Plenty of space for electronics and FPV equipment
• Individual component mounting options for a neat and tidy install
• Pre-angled FPV camera mount for high speed flight
• Large battery compartment can accommodate batteries up to 2200mAH
• Built-in XT60 bracket protects battery cables from prop/crash damage
• 16 & 19mm motor mount bolt hole spacing

Specs:

• Frame Diameter: 270mm
• Material: Carbon fiber / aluminum
• Frame Weight: 190g
• Motor Mount Bolt Hole spacing: 16, 19mm

Required:

• 4 x Motors 1806~2208
• 1 x Battery 1300~2200mah 11.1 ~ 14.8v (3 or 4 cells LiPoly)
• 4 x Propellers up to 6in
• 4 x ESC’s 7~20A
• 1 x multi-rotor flight controller
• 4ch radio (6ch recommended for FPV and FC use)
• FPV gear (optional)

Applicable to be used with Arms of 30mm diameter carbon tube.

30mm Folding Arm Tube Joint for Multicopter is the new product designed for large multi-copter. The assembly is without complicated modification. Just cut the boom of fuselage and assemble the hinge, your multi-copter will be modified to a foldable one! Applicable to multi-copter with 30mm diameter booms. Designed by the newest concept, the product is with light weight and high strength. You don’t need any tool to fold or unfold the multi-copter. Easy and convenient to use!

Features:
1:Round screw locking structure, very convenient, very tight locking.
2:Arm can be folded back to the horizontal shape, save space . Folding angle is around 120-130 degrees.
3:Applicable to tubes of diameter 30mm carbon tube .
4: Material: 6061 Aluminum Alloy

Package included: 1pcs * Aluminum Folding Arm Tube Joint

Applicable to be used with Arms of 40mm diameter carbon tube.

30mm Folding Arm Tube Joint for Multicopter is the new product designed for large multi-copter. The assembly is without complicated modification. Just cut the boom of fuselage and assemble the hinge, your multi-copter will be modified to a foldable one! Applicable to multi-copter with 30mm diameter booms. Designed by the newest concept, the product is with light weight and high strength. You don’t need any tool to fold or unfold the multi-copter. Easy and convenient to use!

Features:
1:Round screw locking structure, very convenient, very tight locking.
2:Arm can be folded back to the horizontal shape, save space . Folding angle is around 120-130 degrees.
3:Applicable to tubes of diameter 30mm carbon tube .
4: Material: 6061 Aluminum Alloy

Package included: 1pcs * Aluminum Folding Arm Tube Joint

RP-SMA Plug to SMA Jack adaptor. basically its Hole to hole adaptor, so if you have Antenna and VTX with pins- this is the adaptor to use

Scope of delivery- 1 adaptor

Please see the DIAGRAM to understand your desired connection

RP-SMA Plug to SMA Jack adaptor.90 degrees version. basically its Hole to hole adaptor, so if you have Antenna and VTX with pins- this is the adaptor to use

Scope of delivery- 1 adaptor

Please see the DIAGRAM to understand your desired connection

MPA is a Multi-Port Safe Parallel Module for safely interconnecting up to 4 Lipos with same-cell-count batteries in parallel
 

• Balance Output Cable: 18AWG silicon cable
• Current: Support MAX. 35A charge current
• Support up to 4 packs 2S-8S balance charge.

Features:

• Supports up to four packs of the same type, same cells 2-8S battery pack.
• Balanced port output line with 18AWG multi-strand silicone line.
• Equipped with safety protection
• High-quality gold-plated connectors.
• Thicken PCB copper foil, allow security using 35A charging current
• Equipped with 40A fuse between any two groups of batteries, to prevent line burned due to the large battery pressure.

Package Included:
1x Parallel Charging Board

MPA is a Multi-Port Safe Parallel Module for safely interconnecting same-cell-count LiPo batteries in parallel; also supports RX/TX NiCds. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.
 
Spcifications:
support for safe parallel charging of up to 6 same-cell-count packs at one time (2s-8s);
supports 40A max charge/discharge rate;
every port reverse polarity fuse protection of main battery wires;
every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators;
supports non-balanced charge of up to two 1s LiPos used with "indoor models";
supports 1 RX and 1 TX NiCd/NiMH battery pack
Works with any Cellpro charger or battery workstation equipped with "XH MODE WIRING" option. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring.
 
Be sure to purchase the proper cable to plug the MPA into your Charger or Battery Workstation.

This super glossy Sam X220 quadcopter frame is made of coated 3K carbon with chamfered edges in high gloss design.

**Combo comes with:

• CC3D controller
• 4 x esc
• 4- Motors 2203/2206
• Props 5"
• Camera
• VTX
• Antenna mushroom
• Lipo 3s 1400-1550

**If you wish to modify or build up your combo with certain components- just contact us. WE promise to respond within Hour( in working hours)

Thanks to specific design the color is deeply inside carbon, and gives you stunning looking frame.

Colors availiable: (see options) and other images to understand the colors

• Transparent Carbon with Blue
• Transparent Carbon with Red
• Transparent Carbon with Green
• Lamborghini Green(not transparent)

Flexible operational
This process is mirrored after what is called a honeycomb, and is used in many strength applications like airplane wings for ultra-light weight and strength, other frames are made of some carbon fiber and a glue type filler which does not allow for vibration dampening or flex.

Features                                    

• Internal layer design,coating on surface like mirror,lighter weight,high strength                                    
• camera bolts to the side plate no gap                                    
• YFS screws,hardness is level 12.9 of Gold screw with screw gasket                                    
• Arbitrary Angle adjustment,Seamless docking,highly rotating tension,no loose, Translation: this baby will take a hit!                                    

This special process, frame performance will Absorb the propeller and motor vibrations.             

• Weight of Frame 64-66 Gr     
• Frame Size : 220mm
• Lower frame 4mm 3k carbon
• made for Props of 5"

This super glossy Sam X220 quadcopter frame is made of coated 3K carbon with chamfered edges in high gloss design, hand crafted.

Thanks to specific design the color is deeply inside carbon, and gives you stunning looking frame.

Colors availiable: (see options) and other images to understand the colors

• Transparent Carbon with Blue
• Transparent Carbon with Red
• Transparent Carbon with Green
• Lamborghini Green(not transparent)

Flexible operational
This process is mirrored after what is called a honeycomb, and is used in many strength applications like airplane wings for ultra-light weight and strength, other frames are made of some carbon fiber and a glue type filler which does not allow for vibration dampening or flex.

Features                                    

• Internal layer design,coating on surface like mirror,lighter weight,high strength                                    
• camera bolts to the side plate no gap                                    
• YFS screws,hardness is level 12.9 of Gold screw with screw gasket                                    
• Arbitrary Angle adjustment,Seamless docking,highly rotating tension,no loose, Translation: this baby will take a hit!                                    

This special process, frame performance will Absorb the propeller and motor vibrations.             

• Weight of Frame 64-66 Gr     
• Frame Size : 220mm
• Lower frame 4mm 3k carbon
• made for Props of 5"

Stainless Screw Self tapping 3x20mm, 10 pcs

Stainless Screw Self tapping 3x25mm, 10 pcs

Product: Screwdriver Holder

Color: Black

Materials: Metal

Rod diameter: 3.5 (mm)

Full length: 180 (mm)

Tool bar length: 100 (mm)

Blade size: 2mm

Weight: 150 (g)

Package:

1* Screwdriver Holder- tools not included

Soldering Station with digital display, 160-480 °C, with soldering irons and soldering and soldering iron holder and sponge

Cheap soldering station for hobby and workshop. The temperature can be continuously adjusted using the control dial of 160-480 ° C. Performance depending on the temperature to about 40 watts.
 

• On and off switch with light
• LCD display for temperature with blue back light
• Rotary controls for temperature
• Soldering iron with tip and 1m cable
• Solder Sponge for wiping the tip
• Drawer for Soldering
• soldering Iron Holder
• Specifications
• Operating voltage: 230V (220-240), 50 Hz
• Soldering iron power: about 48W
• Temperature range: 160-480 ° C
• Weight: about 630g
• Dimension (BxHxL): approx 98x70x155mm

Included:

• Soldering Station ZD-8906L with soldering iron tip
• English user manual

Don't have the battery slip out while flying out of the switch or just lock in the servo extensions securely
Clip for servo connector or extension lead joint, to prevent the connection breaking under outside force.

10pcs in set

colors:

• Blue
• Purple
• Yellow
• Green
• Black

• Lock Clips prevents Servo Extenstion Connections From disconnection in the air, best connector Insurance
• Loghtweight and stable will not impose any burden on your model
• Could Save Your model From A Costly Crash If A Servo Becomes Un-Plugged
• Easy to Install,Fit All Servo Extensions Including JR, Futaba, Hitec, Spektrum, Airtronics, etc.

Set of 10.

Choice of colors

Servo Lever Carbon fiber arm 38mm Type A for Futaba

Specifications:

• The high-quality carbon fiber plastic is optimally matched to this servo arm.
• With a weight of 2.4 g it is only half the weight of aluminum, with the same strength.
• The internal gear is manufactured with precision for displayed under "Versions" servo types.
• Due to the smaller mass, compared to aluminum and a plastic own damping the transmission of the servos work longer play.
• The bores of servo arms are 2.6 mm, it is readily possible to screw a screw M3.

Servo Lever Carbon fiber arm 38mm Type B for Futaba

Specifications:

• The high-quality carbon fiber plastic is optimally matched to this servo arm.
• With a weight of 2.4 g it is only half the weight of aluminum, with the same strength.
• The internal gear is manufactured with precision for displayed under "Versions" servo types.
• Due to the smaller mass, compared to aluminum and a plastic own damping the transmission of the servos work longer play.
• The bores of servo arms are 2.6 mm, it is readily possible to screw a screw M3.

There will be a time when you strip out a wire from your servo extension plug or you simply need to shorten a servo lead to make your model neater and keep your wires away from moving parts. There are 10 sets of Male and Female connectors provided which can be used to create/repair Servo leads and Extensions.

Great for servo replacements or for making your own servo extensions.

This a set of 10 Sets of Housings (plugs). Each set comes with 10 x Male (2 housings, and 10 x Female) and Comes complete with 30 gold Male and Female pins.

So you will get a total of 30 housings, and 60 Pins (30M+30F). You will need your own Crimp tool (can be purchased separately)

This product is Made in Germany

Shim Washer Din 988 10x16x0.1mm (10 pcs)

Shim Washer Din 988 10x16x0.2mm (10 pcs)

Shim Washer Din 988 10x16x0.5mm (10 pcs)

Shim Washer Din 988 10x16x1.0mm (10 pcs)

Shim Washer Din 988 8x14x0.5mm (10 pcs)

Shim Washer Din 988 8x14x1.0mm (10 pcs)