AVIZAR

1 Pair of 16X5 Carbon Fiber Propellers CW/CCW for multicopter

Specifications:

  Material:Japan made carbon fiber
  Epoxy resin cover
  Size:16X5 cw, 16X5ccw
  High gloss 3K finish
  Very strong and light weight

Included : Pair: 1 CW, 1 CCW

Multicopter led Light 50mm, available in yellow
, size is 50mm long, 12m wide.
This light has 4 strong SMD led chips, gives you perfect visibility in day time, or during the race. Operating voltage- 5V DC

Produced in Europe, this Retractable landing gear will allow you full turn of 3 axis Gimbal without seen your Landing legs in Flight.

Exceptional design with Ball  bearings mechanism, with only one servo operation, Full carbon fiber, make this gear set weight less than 330 Grams!: Means it wil not overload your current Drone!

Operated by 2 X Savox Servos (Not included), with Locking mechanism when in Landing position makes it the most desired part.

Tested with the weight of 40KG load.

Completely Flat (when in flight)

Specification:

Weight: 350 gr

• Base plate wideness: 30cm
• Height : 45 cm (allows large gimbals, can be cut down)

Slim size esc for small multicopters: 12mm ONLY, with oneshot and damped lightenabled!

Use new process ultra-low resistance MOSFETs with consideration of size,All flashed N-MOS with high withstanding current;
Slim design, Mini 20A with high performance capacitor filter onboard, weight reduced to 2g

Specification:
Voltage: 6-16.8V(2-4S LiPo)
Output Current: 20A
BEC: Without
Output PWM frequency：18KHz
Firmware：BLHeli 13.2
Weight：2.0g(without wires)
Size：23*12*4.5mm

This is a multifunctional battery protection board designed for racing drones. It's designed to sit over your LiPo Battery to provide it with a protective shell. In addition, it has functions such as voltage monitoring, low voltage alarm, LED navigation lights, and an active out of control alarm.

Battery voltage monitor: Display the battery real-time total voltage through a digital display.

Low voltage alarm: The voltage alarm can be set so that when a cell reaches the preset alarm voltage (3.3-3.7V), the buzzer starts to alarm and the LED lights start to flash.

Multicolour LED navigation lights: The board incorporates LEDs on top and at the rear with seven different colour options to select from.

Active out of control alarm function: When the battery board is powered on, it starts counting and the buzzer will start to beep in 6 minutes - a useful feature to help you find your quad if you lose it in long grass.

Features:

Plug and Play - Powered by a 4S or 3S LiPo Battery Balance Plug
Multicolour LED Lights
Battery Voltage Monitor
Low Voltage Alarm
6 Minute Buzzer
Please Note: The device is powered by a 4S or 3S LiPo battery's balance plug. Default factory setting is for a 4S LiPo battery. If a 3S LiPo battery is used, the positive wire should be soldered to the pad marked as “3S+” on PCB.

Multi rotor ( QUAD) Wood 15x5.5 Propeller Set  1 x CW and 1 x CCW

Multicopter prop from Avizar produces some of the finest props for Multirotor use, and the new Wood Series props offers a wide selection a sizes that are specifically for use in hovering flight applications. All of the various size wood Multirotor props included are in both normal and reverse rotation. The blades on these props feature an elliptic blade shape that produces a more uniform thrust distribution across the entire blade surface for maximum lift and thrust efficiency.

The 15x5.5 props have a 8mm diameter center hole, and including an adapter to fit 6mm shaft .
Wood props are the most lightweight props and best used for best response on drones.

Included:

  Set of 2 props: 1 x CW and 1 x CCW
  2 bushings 6/8mm

Multi rotor ( QUAD) Wood 16x4.5  Propeller Set  1 x CW and 1 x CCW

Multicopter prop from Avizar produces some of the finest props for Multirotor use, and the new Wood Series props offers a wide selection a sizes that are specifically for use in hovering flight applications. All of the various size wood Multirotor props included are in both normal and reverse rotation. The blades on these props feature an elliptic blade shape that produces a more uniform thrust distribution across the entire blade surface for maximum lift and thrust efficiency.

The 16X4.5 props have a 8mm diameter center hole, and including an adapter to fit 6mm shaft .
Wood props are the most lightweight props and best used for best response on drones.

Included:

  Set of 2 props: 1 x CW and 1 x CCW
  2 bushings 6/8mm

Multi rotor ( QUAD) Wood 18X5  Propeller Set  1 x CW and 1 x CCW

Multicopter prop from Avizar produces some of the finest props for Multirotor use, and the new Wood Series props offers a wide selection a sizes that are specifically for use in hovering flight applications. All of the various size wood Multirotor props included are in both normal and reverse rotation. The blades on these props feature an elliptic blade shape that produces a more uniform thrust distribution across the entire blade surface for maximum lift and thrust efficiency.

The 18X5 props have a 8mm diameter center hole, and including an adapter to fit 6mm shaft .
Wood props are the most lightweight props and best used for best response on drones.

Included:

  Set of 2 props: 1 x CW and 1 x CCW
  2 bushings 6/8mm

High-intensity light wire that glows strong at night. The driver ( a tiny black box ) can power up to three light wires each measuring at 1-2 meter long and can run for about 4 hours on a battery, recommended to use 2-3s Lithium.The Cool lights produces no heat and very flexible and bendable so you can wrap it over the Helicopters boom, canopy and other surfaces.Shake proof, impact proof and very versatile each install cold wire produces no electromagnetic wave so it will not interfere with the Helicopter’s receiver signals which is very important.Our Night Wires are especially produced for Military Night Flying, and used on many UAV's and other applications where most of reliability needed.

Those Wires are produced in Europe, and producing 25% more illumination compared to their competitors. And all this without extra consummation of power. very high efficiency.Avaliable in thicknesses of 1.3-3mm, flexible capabilities , and 1.5-2meters, Long enough to wrap the tail boom.You will need converter and Battery 7.4-12v to have the full Application.Note: Out converter can light up to 3 wires at the same time.

Designed and built upon the successful foundation laid by its predecessor, the NEW i4 is a charger featuring state of the art design and functionalities. It is designed to work immaculately with a large variety of rechargeable batteries, and is capable of charging 4 batteries simultaneously. With its accelerated charging rate up to 1.5A, fully charging large capacity batteries will no longer be a dreadful process. The ingenious Active Current Distribution (ACD) technology allows the NEW i4 to bring the entire charging process to an orderly manner depending on user preferences. The new technologies incorporated allows it to distinguish non-rechargeable batteries from rechargeable ones, and the NEW i4 adopts the appropriate charging mode for different battery types and capacities. Users may also configure its settings to suit their individual needs. Four independent indicators provide real time feedback on battery status.

Product Highlights:

• 4 Bay Charger
• Multiple charging speeds - .375A x 4, .5A x 2, .75A x 2, or 1.5A x 1
• LEDs show the charging status of each cell
• Automatically turns off when charging is complete
• Reverse polarity protection protects if cell is entered in the wrong way

Packaging Contents:

• Nitecore i4 Intellicharger
• Standard EU Power Cable
• User Manual

Additional Features:

• Active Current Distribution (ACD) Technology
• Compatible with 1.2V, 3.7V, 4.2V, 4.35V batteries
• Charging program optimized for IMR batteries
• Automatic current selection based on battery capacity
• Automatic detection of non-rechargeable Lithium batteries
• Terminating threshold for battery voltages and charging current can be set independently for each slot
• Capable of charging four batteries simultaneously
• Automatic adoption between three charging modes (CC, CV, and dV/dt)
• Automatically detects battery power status and displays charging progress
• Automatically stops charging upon charging completion
• Reverse polarity protection and short circuit prevention
• Over-discharged battery recovery
• Overtime charging protection
• Designed for optimal heat dissipation
• Made from fire resistant, flame retardant PC material
• Certified by RoHS, CE, FCC and CEC

Nitro Fuel Line Translucent Silicone tube 2.5x4.5mm, 1m long, made from Hi temp silicone

Especially for pressure and density applications, where no faults expected such as use in Helicopters, Airplanes, Cars .

Dimensions
Inner ID: 2.5mm
Outer ID: 4.5mm
Length: 1M
Temperature : -60C to 220C

Nitro Fuel Line Translucent Silicone tube 2.5x5.5mm, 1m long, made from Hi temp silicone

Especially for pressure and density applications, where no faults expected such as use in Helicopters, Airplanes, Cars .

Dimensions
Inner ID: 2.5mm
Outer ID: 5.5mm
Length: 1M
Temperature : -60C to 220C

Made from Aftermarket High Density material , fits All clutch systems in thickness of 1 or 1.5mm

4 pieces of 180x12mm (can be delivered or as 1 pcs 60 x 200mm +-) for easier personal adaptation

DO NOT USE a normal Epoxy, it will not work!!! Best glue to use JB WELD(click to see)

Why do i need aftermarket material?

The material used in today systems example Align, and others is very thin, around 0.8-1mm.

After seen a lot of clutches broken in the air, the solution is  aftermarket material.

The main reason for those breaking clutches is the distance between the clutch and the material.

Example, the diameter of clutch (metal ) is 53mm, and the liner installed is 54. 1mm is free space allow the clutch to expand.

Material which clutch made from is spring metal which expand with turning, but it is very limited, and can expand to 0.3-0.5mm ,if more space is there, the clutch might break.

So if you need to change the liner, use thicker material and do the following:

Measure the clutch and the clutch bell, lets assume the clutch is 53mm, and the bell is 56.

If you put 1mm, it will be 54mm, so 1mm too much space- risk to break.

If you use 1.5mm, its better, however the clutch will be tight to insert,

In this case prepare the liner, and put manually into the clutch bell, if the clutch doesn’t go inside, please take it out and with the help of sandpaper 80-120, sand little for all the length and do the fit again.

You need to come to the point when the clutch will enter with a little force, and will show like it turns not easy.. but still turns. At this stage, glue all and make the fit test, if needed, sand the material inside the bell .

The result- after you start the heli first time, the clutch will show difficulty to turn, but after 2-3 flight it will “find it way” and it will have perfect fit. And it will last for very long time.

Add a little style, Grip and protection to your TX switches ! These non-slip silicone covers are molded to fit the standard switch types used on a wide variety of RC transmitters. Great for your Jeti, Mikado, FrSky, FlySky, Futaba, JR and Others (TX switch must be Flat)

Set Includes

5x LONG switch Non-Slip Silicone Transmitter Switch Cover

5x SHORT switch Non-Slip Silicone Transmitter Switch Cover

Colors:

• Black
• Blue
• Red
• Yellow
• White
• GREEN
  
• Multicolor

Self locking nuts, M2.5 with plastic safe layer, vibration proof , Pack of 10

Self locking nuts, with plastic safe layer, vibration proof , Pack of 10

Self locking nuts M5, with plastic safe layer, vibration proof , Pack of 10

Self locking nuts, with plastic safe layer, vibration proof , Pack of 10

These Lock Nuts are quality 304 stainless steel which is high hardness and provides excellent rust resistance, making it long last use

With nylon insert collar that is non-corrosive, these hex nuts greatly reduce loosening under vibrations and torque, providing better security and firm hold and keep good performance even after multiples times of use

These nuts are great to have around for use in wet or/and vibration environments. They are strong, corrosion resistant and will support all of your projects.

Nylon & Plane pinned Hinges L20×W36mm

Set of 10pcs

Nylon Screws - Pan Head Phillips M4x45

Set of 10 Screws.

Nylon Servo Horn - Heavy Duty - Glassfibre Reinforced - Double 70mm - 25T Futaba

Set of 2 pcs

Nylon Servo Horn - Heavy Duty - Glassfibre Reinforced - Single 35mm - 25T Futaba - 2 pcs

Nylon thumb screws plastic screw bolt M4x30

Set of 10 Screws.

The parallel charge leads allow you to extend charge up to six battery packs simultaneously. Charging extension Cable for 5pcs walkera, Hubsan 1s Lipo
Constructed from the highest quality materials, they give you the best connection possible every time you charge your batteries.

This unique design serves as both a charging and balancing cable for up to 5 of your 1S battery packs. Connect to your batteries with the connectors, as used in the walkera, Hubsan  1s lipos.. extension of 30cm, with Walkera Female 1s connector at the end.

The parallel charge leads allow you to charge up to six battery packs simultaneously.Charging Cable for 6pcs MCX,MSR,MSRX,NANO CPX 1s Lipo
Constructed from the highest quality materials, they give you the best connection possible every time you charge your batteries.

This unique design serves as both a charging and balancing cable for up to 6 of your 1S battery packs. Connect to your batteries with the connectors, as used in the Nano CPX, MCX and other 1s lipos.. Connect to the charger's main output with 4mm banana plugs, and to the balance port with a standard 2S JST-XH balance connector. 10cm of top-quality silicone wire gives you the flexibility you need to easily get everything connected.

The parallel charge leads allow you to charge up to six battery packs simultaneously.Charging Cable for 6pcs Walkera, Hubsan.. 1s Lipo
Constructed from the highest quality materials, they give you the best connection possible every time you charge your batteries.

This unique design serves as both a charging and balancing cable for up to 6 of your 1S battery packs. Connect to your batteries with the connectors, as used in the Walkera, Hubsan 1s lipos.. Connect to the charger's main output with 4mm banana plugs, and to the balance port with a standard 2S JST-XH balance connector. 10cm of top-quality silicone wire gives you the flexibility you need to easily get everything connected.

Built-In 5V and 12V regulators supply ample amount of clean, filtered power to the electronics.
ESC Signal pads allow clean and efficient builds with less wire.
Programmable RGB LEDs let user play with endless colours and features through the flight controller using Cleanflight-Configurator.
XT60 connector is directly mounted onto the PDB (further reducing weight by eliminating heavy wires as well as risk of cutting power leads).
Dedicated signal pads are aligned with the flight controller to allow clean connections.

The black Liquid Tape is a rubber coating that insulates and seals your cables, electrical circuits, servo motors, ESCs, etc. It is applied with a brush directly on the circuits to be protected, and remains very easy to remove once dry, thus leaving you access to the components.
Do-It-Yourself rubber coatings, Performix by Plasti Dip liquid electrical tape coatings allow you to rubberize, insulate, and seal all of your electrical connections. It is a dielectric coating which seals out moisture and other contaminates permanently. Liquid Tape is the most effective product on the market with a dielectric protection of 48,000 V/mm, it does not harden, puncture or become brittle, even in extreme weather conditions.
An applicator brush is included.

Features:

Flexible--won't crack, chip, or become brittle
Insulates from electrical shock, vibration, and heat
Grip provides safe, non-slip comfort and control
Durable--resists weather, chemicals, impact, and abrasion

Piston ring for WEBRA SPEED 61 / P5F Heli, 10ccm / 61 SILVERLINE 1030/4A

The piston ring is the ring that goes between the piston and the cylinder liner
(or sleeve) on a "ring" engine (not an ABC engine).

Piston ring for WEBRA SPEED 80 AERO #1038/4A

The piston ring is the ring that goes between the piston and the cylinder liner
(or sleeve) on a "ring" engine (not an ABC engine).

Differential pressure Sensor board 14g only

The MPXV7002 series piezoresistive transducer in the small sketch package (SOP) is a state-of-the-art monolithic silicon pressure sensor designed for a wide range of applications, especially those involving a microcontroller or microprocessor with ONE / D inputs. This patented, single element transducer combines advanced micromachining techniques, thin film metallization and bipolar processing to produce an accurate high analog output signal proportional to the applied pressure.

The MPXV7002 is designed to measure positive and negative pressures. In addition, with an offset specially at 2.5 V instead of the conventional 0 V, this new series can measure pressure up to 7kPa through each port for pressure sensing but also for vacuum sensing (see the transfer function in the data sheet for more detailed information). Features: -2 to 2 kPa (-0.3 to 0.3 psi). 0.5 to 4.5 V Output

Electronics not included

Plain Washers ISO 7089 A2 10x20x2.0mm (10 pcs)

Plain Washers ISO 7089 A2 10x24x2.5mm (10 pcs)

Plain Washers ISO 7089 A2 3x7x0.5mm (10 pcs)

Plain Washers ISO 7089 A2 4x8.5x1.0mm (10 pcs)

Plain Washers ISO 7089 A2 8x16x1.5mm (10 pcs)