AVIZAR

Motor Shaft for Avizar motors

This is a set of Multicopter Motors, perfect for 250 size model FPV racers. Set including CW and CCW self locking adaptor motors.

• The magnet  is 40 uh.
• Long life Japanese NMB bearings
• 0.20mm laminations, maximum efficiency and minimum losses.
• Ultra-flexible motor leads with high-temp 220 °silicone rubber.
• 2mm Bullet connectors.
  
• With rotor dynamic balance process.
• The prop adapters in CW/CCW rotation

Specifications:

• KV: 2000
• Configuration: 12N14P
• Stator Diameter: 22mm
• Stator Length: 6mm
• Shaft Diameter: 3.0mm, OD:2.0mm
• Motor Dimensions(Dia.*Len): 28×18mm
• Weight (g): 30g
• No.of Cells(Lipo): 2-3S
• Max Continuous current(A): 14.7A
• Max Continuous Power(W): 163.2W
• Internal resistance: 0.098Ω

Package includes:

1x 2206-2000KV CW motor
1x 2206-2000KV CCW motor
Set of connectors (not soldered)

Muffler Pressure Nipple - M3 - 2 pcs, for DIY

Muffler Pressure Nipple - M4 - 2 pcs, for DIY

Multi Function Motor Grip Plier  For RC Models

Designed to grip the can of your electric motor without Scratching it.
Silicon inserts help prevent scratching and allow you to get a better grip of your prop nut/spinner making removal of your propeller far easier.
Can be used on any round object that needs gripping such as print heads on 3D printers, carbon fiber or aluminium tubes or even hold the handle of a driver to get more leverage.

Multi harness cable 15cm for receiver and flybarless system or multicopters Flight controllers

Package includes:

• 1 multi harness cable lead 15cm.

Working with big 6S packs? Cut the clutter and get the one board that's designed specifically for your application.

Designed from the ground-up with one purpose, this board is as straightforward as we could make it, with EC5 and 6S JST-XH connectors for up to four packs in parallel. With fuse protection on both the main and balance connections, you can rest easy knowing that all your gear is protected from any short circuits. 40A blade fuses on the main circuits are easily replaceable if needed, while the balance circuits have self-resetting poly-fuses built into the board.

With both main and balance cables included to connect to whatever charger you're using, this is a true plug-and-play solution.

 MC3510 size motor especially developed for the Multi-rotors platforms. Fits props with 6mm hole and Flat props

• Motor diameter: 42.5mm
• Configuration : 12N14P
  
• Length: 31.5mm
• Stator Diameter:35mm
• Shaft : m5
• Weight: 97 Grm
• Input voltage: 3-6S, 11-22V
  
• No load current: 0.7A
• Max load current: 25A
  
• Internal resistance: 0.062 Ohm
• Top mounting holes: 12/17mm, M3
  
• Bottom mounting: 25/25, M3
• Recommended esc: 30Amp

Wire length : 50cm

Delivered with prop adaptor 6mm and Flat prop adaptor

MC3536-380kv , made for 6S setups, and is a high torque motor especially developed for the Multi-rotors platforms .

This motor has been custom designed and tested during 2 years, and found to be the most efficient for most multi-copters from 500cm and up, due its features.

So what is so special in this motor:

1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

2- Heat, 25% lower heat generation thanks to ceramic bearings.

3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.

4- 60cm cables, will allow direct connection to most size frames, up to 1.2 meters.

5- Special size of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.

Specifications:

•     No-load speed: 380kv
•     Load current: 19Amp
•     Burst Amps : 30 Amps
•     Power: 430 W
•     Short shaft
•     Propeller mount diameter: 6mm
•     Long cables (60cm)
•     3 x Ceramic Hybrid bearings
•     Weight: 104gr
•     Size : 35 x 36 mm
•     Poles: 14
•     Recommended Battery: 6S, 22.2V
•     Resistance 44 mOhm
•     Idle current @ 10v :0.7 Amps
•     Propellers to use: from 12" to 14"

    Included:

    MC3536-380KV motor
    Propeller mount with screws, Nut and Cup provided for choice.

See the movie showing Sky hero setting a speed record using the MC3536 motor

MC3536 is a high torque motor especially developed for the Multi-rotors platforms . made for 4-6S setups.

This motor has been custom designed and tested during 2 years, and found to be the most efficient for most multi-copters from 500cm and up, due its features.

So what is so special in this motor:

1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

2- Heat, 25% lower heat generation thanks to ceramic bearings.

3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.

4- 60cm cables, will allow direct connection to most size frames, up to 1.2 meters.

5- Special size of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.

Specifications:
 

•   No-load speed: 710kv
•   Load current: 23Amp
•   Burst Amps : 32 Amps
•   Power: 340 W
•   Short shaft
•   Propeller mount diameter: 6mm
•   Long cables (60cm)
•   3 x Ceramic Hybrid bearings
•   Weight: 104gr
•   Size : 35 x 36 mm
•   Poles: 14
•   Recommended Battery: 4S, 6S for Speedy machines!
•   Resistance 44 mOhm
•   Idle current @ 10v :1.7 Amps
•   Propellers to use: from 11" to 13"

  Included:

  MC3536-710KV motor
  Propeller mount with screws, Nut and Cup provided for choice.

Movie shows the Sky hero setting a record using this motor

Multicopter Power distribution Board PDB 100Amp

Allows connection up to 16 ESC or other peripherals to this Board

Slim size esc for small multicopters: 13mm ONLY, with oneshot and damped lightenabled!

Features

• Ultra-light and ultra-small ESC beyond imagination
• Powered by high performance EFM8BB21 MCU
• Flashed with the latest BLHeli_S program
• With the combination of dedicated drive chip
• Composed of 3 Oz gold plated PCB.

Specification

Item: 45A Brushless ESC
Power Cable: 18#,90mm
Signal Cable: 150mm
Voltage: 2-6S
Continuous Current: 45A
Peak Current: 55A (10S)
Support Protocols: ONESHOT125,DSHOT125/300/600
Size: 13*28.5mm

Multicopter Quadrotor 5010-14 360KV Brushless Motor

1.Machined aluminum front housing with four fan-style cooling holes that pump air through the motor while it runs.

2.Rear threaded mounting holes with both 16 mm and 19mm hole spacing fit a variety of applications.

3.Specially designed NdFeB magnets with high temperature rating for trouble-free operation.

4.High Temperature 140 C (356 F) rated wire is used for winding the motors to minimize the risk of burning up the motor.

5.High quality stator plates are epoxy coated on the inner surface to prevent winding shorts. 0.20mm stator plate id used .

6.High quality shielded and permanently lubricated ball bearings are used to support the motor shaft in all our motors.

7.High temperature adhesives are used to secure the stator windings and prevent them from shifting and getting pinched or shorting out .

• Model: D5010-14
• Motor size: 50*10mm
• Shaft size: 3.17mm
• Weight: 80g
• KV(rpm/v): 360
• Battery: 2-6Li-Po
• ESC: 10A
• Cable 40cm
• Best working with props of 14-16"

 85A Programmable Brushless Speed Controller ESC

Specifications

85A ESC
Output: Continuous 85A, Burst 100A up to 10 Secs.
Input Voltage: 2-6S Lipo
sBEC: 4A/5.5V

Dimensions W*L*H:33 x 60x 17(mm)
Weight: 60g

These are all new props on the market. They are built to a higher standard than the normal prop manufactures and will require little to no balancing.

Set of 4 props 9x4.5, 2cw+2ccw

2 sets of Adaptor Rings.

• Material:Japan made carbon fiber
• Epoxy resin cover
• Size:12X4.5 cw, 12x4.5ccw
  
• High gloss 3K finish
• Very strong and light weight

1 Pair of 13x4 Carbon Fiber Propellers CW/CCW for multicopter

Specifications:

  Material:Japan made carbon fiber
  Epoxy resin cover
  Size:13x4 cw, 13x4ccw
  High gloss 3K finish
  Very strong and light weight

Included : Pair: 1 CW, 1 CCW

1 Pair of 14x4.7 Carbon Fiber Propellers CW/CCW for multicopter

Specifications:

  Material:Japan made carbon fiber
  Epoxy resin cover
  Size:14x4.7 cw, 14x4.7ccw
  Hole 6mm
  High gloss 3K finish
  Very strong and light weight

Included : Pair: 1 CW, 1 CCW

1 Pair of 15X4 Carbon Fiber Propellers CW/CCW for multicopter

Specifications:

  Material:Japan made carbon fiber
  Epoxy resin cover
  Size:15X4 cw, 15X4ccw
  High gloss 3K finish
  Very strong and light weight

Included : Pair: 1 CW, 1 CCW

1 Pair of 16X5 Carbon Fiber Propellers CW/CCW for multicopter

Specifications:

  Material:Japan made carbon fiber
  Epoxy resin cover
  Size:16X5 cw, 16X5ccw
  High gloss 3K finish
  Very strong and light weight

Included : Pair: 1 CW, 1 CCW

Multicopter led Light 50mm, available in yellow
, size is 50mm long, 12m wide.
This light has 4 strong SMD led chips, gives you perfect visibility in day time, or during the race. Operating voltage- 5V DC

Produced in Europe, this Retractable landing gear will allow you full turn of 3 axis Gimbal without seen your Landing legs in Flight.

Exceptional design with Ball  bearings mechanism, with only one servo operation, Full carbon fiber, make this gear set weight less than 330 Grams!: Means it wil not overload your current Drone!

Operated by 2 X Savox Servos (Not included), with Locking mechanism when in Landing position makes it the most desired part.

Tested with the weight of 40KG load.

Completely Flat (when in flight)

Specification:

Weight: 350 gr

• Base plate wideness: 30cm
• Height : 45 cm (allows large gimbals, can be cut down)

Slim size esc for small multicopters: 12mm ONLY, with oneshot and damped lightenabled!

Use new process ultra-low resistance MOSFETs with consideration of size,All flashed N-MOS with high withstanding current;
Slim design, Mini 20A with high performance capacitor filter onboard, weight reduced to 2g

Specification:
Voltage: 6-16.8V(2-4S LiPo)
Output Current: 20A
BEC: Without
Output PWM frequency：18KHz
Firmware：BLHeli 13.2
Weight：2.0g(without wires)
Size：23*12*4.5mm

This is a multifunctional battery protection board designed for racing drones. It's designed to sit over your LiPo Battery to provide it with a protective shell. In addition, it has functions such as voltage monitoring, low voltage alarm, LED navigation lights, and an active out of control alarm.

Battery voltage monitor: Display the battery real-time total voltage through a digital display.

Low voltage alarm: The voltage alarm can be set so that when a cell reaches the preset alarm voltage (3.3-3.7V), the buzzer starts to alarm and the LED lights start to flash.

Multicolour LED navigation lights: The board incorporates LEDs on top and at the rear with seven different colour options to select from.

Active out of control alarm function: When the battery board is powered on, it starts counting and the buzzer will start to beep in 6 minutes - a useful feature to help you find your quad if you lose it in long grass.

Features:

Plug and Play - Powered by a 4S or 3S LiPo Battery Balance Plug
Multicolour LED Lights
Battery Voltage Monitor
Low Voltage Alarm
6 Minute Buzzer
Please Note: The device is powered by a 4S or 3S LiPo battery's balance plug. Default factory setting is for a 4S LiPo battery. If a 3S LiPo battery is used, the positive wire should be soldered to the pad marked as “3S+” on PCB.

Multi rotor ( QUAD) Wood 15x5.5 Propeller Set  1 x CW and 1 x CCW

Multicopter prop from Avizar produces some of the finest props for Multirotor use, and the new Wood Series props offers a wide selection a sizes that are specifically for use in hovering flight applications. All of the various size wood Multirotor props included are in both normal and reverse rotation. The blades on these props feature an elliptic blade shape that produces a more uniform thrust distribution across the entire blade surface for maximum lift and thrust efficiency.

The 15x5.5 props have a 8mm diameter center hole, and including an adapter to fit 6mm shaft .
Wood props are the most lightweight props and best used for best response on drones.

Included:

  Set of 2 props: 1 x CW and 1 x CCW
  2 bushings 6/8mm

Multi rotor ( QUAD) Wood 16x4.5  Propeller Set  1 x CW and 1 x CCW

Multicopter prop from Avizar produces some of the finest props for Multirotor use, and the new Wood Series props offers a wide selection a sizes that are specifically for use in hovering flight applications. All of the various size wood Multirotor props included are in both normal and reverse rotation. The blades on these props feature an elliptic blade shape that produces a more uniform thrust distribution across the entire blade surface for maximum lift and thrust efficiency.

The 16X4.5 props have a 8mm diameter center hole, and including an adapter to fit 6mm shaft .
Wood props are the most lightweight props and best used for best response on drones.

Included:

  Set of 2 props: 1 x CW and 1 x CCW
  2 bushings 6/8mm

Multi rotor ( QUAD) Wood 18X5  Propeller Set  1 x CW and 1 x CCW

Multicopter prop from Avizar produces some of the finest props for Multirotor use, and the new Wood Series props offers a wide selection a sizes that are specifically for use in hovering flight applications. All of the various size wood Multirotor props included are in both normal and reverse rotation. The blades on these props feature an elliptic blade shape that produces a more uniform thrust distribution across the entire blade surface for maximum lift and thrust efficiency.

The 18X5 props have a 8mm diameter center hole, and including an adapter to fit 6mm shaft .
Wood props are the most lightweight props and best used for best response on drones.

Included:

  Set of 2 props: 1 x CW and 1 x CCW
  2 bushings 6/8mm

High-intensity light wire that glows strong at night. The driver ( a tiny black box ) can power up to three light wires each measuring at 1-2 meter long and can run for about 4 hours on a battery, recommended to use 2-3s Lithium.The Cool lights produces no heat and very flexible and bendable so you can wrap it over the Helicopters boom, canopy and other surfaces.Shake proof, impact proof and very versatile each install cold wire produces no electromagnetic wave so it will not interfere with the Helicopter’s receiver signals which is very important.Our Night Wires are especially produced for Military Night Flying, and used on many UAV's and other applications where most of reliability needed.

Those Wires are produced in Europe, and producing 25% more illumination compared to their competitors. And all this without extra consummation of power. very high efficiency.Avaliable in thicknesses of 1.3-3mm, flexible capabilities , and 1.5-2meters, Long enough to wrap the tail boom.You will need converter and Battery 7.4-12v to have the full Application.Note: Out converter can light up to 3 wires at the same time.

Designed and built upon the successful foundation laid by its predecessor, the NEW i4 is a charger featuring state of the art design and functionalities. It is designed to work immaculately with a large variety of rechargeable batteries, and is capable of charging 4 batteries simultaneously. With its accelerated charging rate up to 1.5A, fully charging large capacity batteries will no longer be a dreadful process. The ingenious Active Current Distribution (ACD) technology allows the NEW i4 to bring the entire charging process to an orderly manner depending on user preferences. The new technologies incorporated allows it to distinguish non-rechargeable batteries from rechargeable ones, and the NEW i4 adopts the appropriate charging mode for different battery types and capacities. Users may also configure its settings to suit their individual needs. Four independent indicators provide real time feedback on battery status.

Product Highlights:

• 4 Bay Charger
• Multiple charging speeds - .375A x 4, .5A x 2, .75A x 2, or 1.5A x 1
• LEDs show the charging status of each cell
• Automatically turns off when charging is complete
• Reverse polarity protection protects if cell is entered in the wrong way

Packaging Contents:

• Nitecore i4 Intellicharger
• Standard EU Power Cable
• User Manual

Additional Features:

• Active Current Distribution (ACD) Technology
• Compatible with 1.2V, 3.7V, 4.2V, 4.35V batteries
• Charging program optimized for IMR batteries
• Automatic current selection based on battery capacity
• Automatic detection of non-rechargeable Lithium batteries
• Terminating threshold for battery voltages and charging current can be set independently for each slot
• Capable of charging four batteries simultaneously
• Automatic adoption between three charging modes (CC, CV, and dV/dt)
• Automatically detects battery power status and displays charging progress
• Automatically stops charging upon charging completion
• Reverse polarity protection and short circuit prevention
• Over-discharged battery recovery
• Overtime charging protection
• Designed for optimal heat dissipation
• Made from fire resistant, flame retardant PC material
• Certified by RoHS, CE, FCC and CEC

Nitro Fuel Line Translucent Silicone tube 2.5x4.5mm, 1m long, made from Hi temp silicone

Especially for pressure and density applications, where no faults expected such as use in Helicopters, Airplanes, Cars .

Dimensions
Inner ID: 2.5mm
Outer ID: 4.5mm
Length: 1M
Temperature : -60C to 220C

Nitro Fuel Line Translucent Silicone tube 2.5x5.5mm, 1m long, made from Hi temp silicone

Especially for pressure and density applications, where no faults expected such as use in Helicopters, Airplanes, Cars .

Dimensions
Inner ID: 2.5mm
Outer ID: 5.5mm
Length: 1M
Temperature : -60C to 220C

Made from Aftermarket High Density material , fits All clutch systems in thickness of 1 or 1.5mm

4 pieces of 180x12mm (can be delivered or as 1 pcs 60 x 200mm +-) for easier personal adaptation

DO NOT USE a normal Epoxy, it will not work!!! Best glue to use JB WELD(click to see)

Why do i need aftermarket material?

The material used in today systems example Align, and others is very thin, around 0.8-1mm.

After seen a lot of clutches broken in the air, the solution is  aftermarket material.

The main reason for those breaking clutches is the distance between the clutch and the material.

Example, the diameter of clutch (metal ) is 53mm, and the liner installed is 54. 1mm is free space allow the clutch to expand.

Material which clutch made from is spring metal which expand with turning, but it is very limited, and can expand to 0.3-0.5mm ,if more space is there, the clutch might break.

So if you need to change the liner, use thicker material and do the following:

Measure the clutch and the clutch bell, lets assume the clutch is 53mm, and the bell is 56.

If you put 1mm, it will be 54mm, so 1mm too much space- risk to break.

If you use 1.5mm, its better, however the clutch will be tight to insert,

In this case prepare the liner, and put manually into the clutch bell, if the clutch doesn’t go inside, please take it out and with the help of sandpaper 80-120, sand little for all the length and do the fit again.

You need to come to the point when the clutch will enter with a little force, and will show like it turns not easy.. but still turns. At this stage, glue all and make the fit test, if needed, sand the material inside the bell .

The result- after you start the heli first time, the clutch will show difficulty to turn, but after 2-3 flight it will “find it way” and it will have perfect fit. And it will last for very long time.

Add a little style, Grip and protection to your TX switches ! These non-slip silicone covers are molded to fit the standard switch types used on a wide variety of RC transmitters. Great for your Jeti, Mikado, FrSky, FlySky, Futaba, JR and Others (TX switch must be Flat)

Set Includes

5x LONG switch Non-Slip Silicone Transmitter Switch Cover

5x SHORT switch Non-Slip Silicone Transmitter Switch Cover

Colors:

• Black
• Blue
• Red
• Yellow
• White
• GREEN
  
• Multicolor

Self locking nuts, M2.5 with plastic safe layer, vibration proof , Pack of 10

Self locking nuts, with plastic safe layer, vibration proof , Pack of 10

Self locking nuts M5, with plastic safe layer, vibration proof , Pack of 10